Dimplex CDFI-TMHEAT Bedienungsanleitung
Owner’s Manual
Model
CDFI-TMHEAT
6910040159
To view the full line of Dimplex products, please visit
www.dimplex.com
7215510100R00
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this heater. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
2 www.dimplex.com
Table of Contents
Always use a quali ed technician
or service agency to repair
this heater.
!NOTE: Procedures and
techniques that are considered
important enough to emphasize.
CAUTION: Procedures and
techniques which, if not carefully
followed, will result in damage to
the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations . . . . . . . . . . . . . . . . . .3
IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . . .4
Heater Installation . . . . . . . . . . . . . . . . . . . . . . . . .6
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase a Dimplex
electric heater.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label of your heater.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and
product serial number ready. (See above)
S E R IAL No.
MODE L
MOD.
4 www.dimplex.com
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
①Read all instructions before
using the heater.
②The heater is hot when in
use. To avoid burns, do not let
bare skin touch hot surfaces.
The surface around the heater
outlet becomes hot during heater
operation.
DANGER: High temperatures
may be generated under certain
abnormal conditions. Do not
partially or fully cover or obstruct
the front of this heater.
③Extreme caution is necessary
when any heater is used by or
near children or invalids and
whenever the unit is left operating
and unattended.
④Always disconnect the heater
when not in use.
⑤Do not operate any heater
after it malfunctions. Disconnect
power at the service panel and
have the heater inspected by
a reputable electrician before
reusing.
IMPORTANT INSTRUCTIONS
⑥ Do not operate any unit with a
damaged cord or if the heater has
malfunctioned, or if the heater
has been dropped or damaged
in any manner, contact
Technical Service at
1-888-346-7539.
⑦Do not use outdoors.
⑧Never locate heater over a
bathtub or other water container.
⑨To disconnect the unit, turn
the controls OFF, disconnect
power at the service panel.
⑩Do not insert or allow foreign
objects to enter any ventilation
or exhaust opening as this may
cause an electric shock or fire, or
damage to the heater.
⑪To prevent a possible fire, do
not block air intake or exhaust in
any manner.
⑫All electrical heaters have
hot and arcing or sparking parts
inside. Do not use in areas where
gasoline, paint, or flammable
liquids are used or stored.
⑬Do not modify the heater.
Use it only as described in
this manual. Any other use
5
SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
not recommended by the
manufacturer may cause fire,
electric shock or injury to persons.
⑭Always use a certified
electrician should new circuits or
outlets be required.
⑮Always use properly
grounded, fused and polarized
outlets.
⑯Disconnect all power supply
before performing any cleaning,
maintenance or relocation of the
unit.
⑰ When transporting or storing
the unit, keep in a dry place, free
from excessive vibration and
store so as to avoid damage.
!NOTE: Changes or
modications not expressly
approved by the party responsible
for compliance could void
user's authority to operate the
equipment.
For Bathroom Use
If this unit is installed in a
bathroom it must be protected
by a GFI receptacle or circuit.
If receptacle is used it must be
readily accessible.
To prevent electrical shock this
unit is an electrical appliance
that is not watertight and must
be installed as to prevent water
from entering unit. This must be
installed away from showers,
tubs, etc. Never locate heater
where it may fall into a bathtub or
other water container.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICABLE PARTS INSIDE
6 www.dimplex.com
Heater Installation
WARNING:
ANY
INSTALLATION AND
SERVICE WORK SHOULD BE
PERFORMED BY QUALIFIED
AND AUTHORIZED PERSONNEL.
ALL INSTALLATIONS MUST
COMPLY WITH ALL LOCAL
CODES AND BY-LAWS,
INSPECTED AND APPROVED
FOR OPERATION BY LOCAL
GOVERNIN
G AUTHORITY PRIOR
TO USE.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
!NOTE: A 15 Amp, 120 Volt
circuit is required. A dedicated
circuit is preferred but not
essential in all cases. A dedicated
circuit will be required if, after
installation, the circuit breaker
trips or fuse blows on a regular
basis when the heater is
operating. Additional appliances
on the same circuit may exceed
the current rating of the circuit
breaker.
Hardwire Installation
The heater is supplied in an
assembled state and is designed
to be permanently installed. The
unit comes ready for hardwire
installation.
WARNING: Do not attempt
to wire your own new outlets or
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
!NOTE: Please read all
instructions before installing.
1. For rough in framing, the
opening should follow the
recommended dimensions
located in Figure 2.
!NOTE: Dimensions provided
are minimum clearances and will
vary depending on type of support
framing and nishing options.
!NOTE: Framing should be
constructed to support 10 lbs
(4.5 kg).
WARNING: To reduce the
risk of re, do not store or use
gasoline or other ammable
vapors or liquids in the vicinity of
the heater.
7
Heater Installation
2. Allow at least 2 ft. (61 cm) of service cable for connecting
the power supply wire.
CAUTION: Keep min 6" clearance to the adjacent walls and min
18” clearance to the oor.
!NOTE: Use minimum 14 AWG supply cable with two insulated
copper conductors (white and black) and one bare ground wire.
!NOTE: The heater only exhausts from one direction. Note this
direction, see gure 7.
0.18"
(4.5mm)
7.6"
(192mm)
8"
(201mm)
5"
(128mm)
15"
(380mm)
Pilot light
0.4"
(10mm)
0.4"
(10mm)
1.3"
(34mm)
12.6"
(321mm)
3.4"
(86mm)
Figure 1
8 www.dimplex.com
326mm
12.83"
17mm
0.67"
17mm
0.67"
36mm
1.42"
128mm
5.04"
360mm
14.17"
ref
206mm
8.11" FINISHED CEILING
MOUNTING OPENING
FRAMING
FOR REF.
MOUNTING
HOLES
LOCATION
Heater Installation
Installation Options
The heater can be installed on its
own or with an Opti-myst cassette.
The unit needs to be installed so
that the heater outlet is horizontal
to the ground. The required
opening dimensions for the
heater are: 12.8" (326 mm) x 8.1"
(206 mm) x 3.5" (89 mm) deep.
!NOTE: The heater does not
require any additional venting.
!NOTE: Install the heater so
that the pilot light can be seen
5 ft (153 cm) from the oor and
10 ft (305 cm) from the unit.
(Figure 3)
Figure 2
Example:
Distance from
oor
Distance from
front wall
54" 6"
36" 2"
9
THERMAL
CUTOUT
120V~ 60HZ
1 23
L1
N
ON/OFF SWITCH
(PILOT LIGHT)
L
N
Relay Board
3001890100
M
HEATING ELEMENT
HEATING ELEMENT
MOTOR
G
Heater Installation
5.0 ft (153 cm)
10.0 ft (305 cm)
Figure 3
Wiring
Distance
from oor
Distance from
front wall
10 www.dimplex.com
Heater Installation
Plugs into Opti-myst cassette
CDFI1000-PRO or
CDFI500-PRO, refer to
the cassette user’s guide.
Heater control
wire. Used when
controlled by the
Opti-myst cassette
CDFI1000-PRO or
CDFI500-PRO.
Cable
Plate
Figure 4
CAUTION: Use two
conductor, non-metallic sheath
cable with ground wire (3 wires
total) for the incoming power
supply. Use appropriate wire to
meet local and national electrical
codes for rated power.
1. On the back of the unit, remove
the cable clamp by removing
the screw at the top (Figure 4).
2. Install a 3/8"(10 mm) or 1/2 in.
(13 mm) cable connector, not
included, suitable for mounting
in a 7/8"(22 mm) hole, to the
cable plate and feed the supply
cable through the connector
and secure.
3. Remove the 3 wires from within
the unit.
4. Connect the black wire (live)
from the unit to the black wire
from power supply.
Inhaltsverzeichnis
Sprachen:
Andere Dimplex Elektrische Heizung Handbücher
Dimplex
Dimplex BN Series Bedienungsanleitung
Dimplex
Dimplex XLE050 Bedienungsanleitung
Dimplex
Dimplex CUH05B31T Bedienungsanleitung
Dimplex
Dimplex PLX 500 Bedienungsanleitung
Dimplex
Dimplex BDG15-AU Bedienungsanleitung
Dimplex
Dimplex DLGM29 Bedienungsanleitung
Dimplex
Dimplex CUH05B31T Bedienungsanleitung
Dimplex
Dimplex VR15 Bedienungsanleitung
Dimplex
Dimplex XLS12N Bedienungsanleitung
Dimplex
Dimplex QSH-70 Bedienungsanleitung
Dimplex
Dimplex WW 101 E Bedienungsanleitung
Dimplex
Dimplex TRFW 201 Service-Handbuch
Dimplex
Dimplex LPC Series Bedienungsanleitung
Dimplex
Dimplex Alta Series Bedienungsanleitung
Dimplex
Dimplex CDFI500-PRO Bedienungsanleitung
Dimplex
Dimplex CUH05B31TG Bedienungsanleitung
Dimplex
Dimplex Cheriton Fire CHT20 Bedienungsanleitung
Dimplex
Dimplex RITZ Bedienungsanleitung
Dimplex
Dimplex Apollo APL100 Bedienungsanleitung
Dimplex
Dimplex DX 512E Bedienungsanleitung
