Dimplex XL12N Bedienungsanleitung
Installation Instructions
Dimplex Ultra-Slim Storage Heaters
Models XL12N, XL18N, XL24N
Twin Sensor Models XLS12N Automatic,
XLS18N Automatic, XLS24N Automatic
(96513 Iss. 12)
IMPORTANT
These instructions should be read carefully and retained for future reference.
Note also the information given on the appliance.
This heater is VERY HEAVY. In order to maintain
stability and to ensure its future safety in use, it is
essential that the heater is FIXED SOUNDLY TOAWALL
and that the feet are mounted on a FIRM, LEVEL
SURFACE. Care should be taken to avoid irregular
surfaces, such as may result from tiled surrounds
partially protruding under the heater. It is important
that the following instructions are strictly followed.
IT IS IMPORTANTTHAT THE FIXING DEVICE CHOSEN
ISAPPROPRIATETOTHEWALLMATERIALTOWHICH
THE HEATER IS BEING FIXED. SOME MODERN
INTERNALBUILDINGMATERIALSAREVERYLOW
DENSITY BLOCK AND REQUIRE SPECIALISED FIXING
DEVICES TO PROVIDEASAFE, SECURE
INSTALLATION.
The installation of this appliance should be carried out by
competentpersonnelandbeinaccordancewith the current
IEE wiring regulations. For the assembly of the heater tools
requiredareaNo.2pozidriver,anelectricalscrewdriverwitha
4mmwideblade anda 8mmAF openended or boxspanner.
Asmall mirror will aid insertion of the front panel retaining
screws.
OnlyHeatResistingCable(min.ratingT85)shouldbeused.
DONOTCOVEROROBSTRUCTthesurfacesofthe
appliance.
DONOTPOSITIONunderwindowswherecurtainsmay
contactthe heater. (Seeminimum clearances, stage6).
DONOTPLACE OBJECTSincontactwiththeheater.
If, during any reassembly of the heater, a part of the thermal
insulationshowsdamageordeteriorationwhichmayimpair
safety, it should be replaced with an identical part.
Connection to a 30 amp Ring Circuit
XLN/XLSN STORAGE HEATERS SHOULD NOT BE CONNECTED TO A 30 AMP RING CIRCUIT.
XL/XLS24N STORAGE HEATERS SHOULD NOT BE CONNECTED TO A FUSED SPUR.
Bricks are in packs of two.
The pack catalogue number is XT 8300
XL12/XLS12N - 12kWh
8 Bricks (4 Packs) XL18/XLS18N - 18kWh
12 Bricks (6 Packs) XL24/XLS24N - 24kWh
16 Bricks (8 Packs)
ThisappliancecomplieswiththeEuropeanStandardsEN60335-1,EN60335-2-61,EN61000-3-2,EN61000-3-3,EN55014andEN55104forSafety&ElectromagneticCompatibility.
ThesestandardscovertherequirementoftheEMCDirectives89/336&73/23
Assembly of heater
1. Invert the carton and carefully lift carton off heater. Do
not remove internal packaging pieces at this stage! 2. Remove the feet and accessories bag from corner
fittings (accessories bag is located within one of the feet).
3. Secure the feet to base of heater using the Taptite
screws provided (two for each foot). It is necessary on
XL12N/XLS12Nmodels, toremove basecorner packaging
pieces to locate feet in position.
4. Loosen hexagon head front panel securing screws, by 1
-2 turns using screwdriver through aperture ineach end
packingpiece.
7. Position heater against wall in intended final position,
taking note of the minimum fixing dimensions.
If fitted, the Dimplex storage heater shelf should be fixed
in accordance with the instructions enclosed with the
shelf.
8. If the floor is carpeted then the carpet should be slit and
underlay cut away to allow the feet to rest firmly on the
floor. Carpet gripper must be locally removed so that the
feet may rest in a level position. 9.Having prepared,where necessary,the floor, the
position of the wall bracket should be marked on the wall.
5. Stand heater on its feet and remove all packaging
pieces.
6. IMPORTANT XLS Models Only - Locating the
external sensor
The sensor is situated at the rear of the lower right corner
of the heater.
a) Remove sensor carefully from its retaining clips and
move to one side.
b) Slide down plastic sensor carrier as far as it will go so
that the two plastic fixings are above the retaining notches.
Replace sensor carefully in its retaining clips.
12.Solid Brick/High Density Block Walls. (See step 13 if
walls are low density block.) These must be drilled and
pluggedwith the Rawlplug No.10 size fibre inserts
provided. The correct size of drill (5.5mm) should be used
and the hole should be drilled to a depth of 6mm greater
that the length of the Rawlplug so that the fixing is made
belowthe plasterlayer.
13. Low Density Block Walls. Aspecialised fixing, such
as the Unifix LB70, should be employed following closely
themanufacturer’sinstructions.
Panelled Internal Walls. Here it is best to locate the
studding and use No. 10 size woodscrews. Where it is not
possible to locate the studding use type M5 Rawlplug
INTERSETSon securely fastenedplasterboard panelling.
Forother wall panel materials the wall panel manufacturer
should be consulted for details of suitable wall fixing
devices.
10. Remove wall fixing bracket from heater by removing
the screws at each end.
11. Mark wall bracket fixing positions and screw wall bracket
to wall following closely the guidelines in steps 12 and 13.
NOTE: It is essential that two of the fixing points are the
lower short fixing slots at each end of the wall bracket.
14. If left hand cable connection is required, the cable
support straps supplied in the fixing kit should be fitted to
the base of the rear of the heater, and the supply cable fed
through them. Ensure sufficient spare cable is fed through
the straps to make the mains connection.
15. Secure heaterto wallfixing bracket by replacing thetwo
screws removed in step 10 (do not fully tighten these screws
until the bricks are loaded into the heater as some settling of
theheatermayoccur).Thefeetandwallmountingarrangement
are designed to accommodate skirting board sizes up to
25mm(1”)thick.Toavoidobstructingtheairflowtothe rear
oftheheaterthe following must bestrictlyadheredto:
(a) For skirtings higher than 100mm (4”) it will be necessary to
positiontheheaterwith the screwsattachedthroughthe
alternative fixing slots to the front.
(b) For skirtings having a height in excess of 150mm (6”) it will
be necessary to reduce the height of the skirting to 150mm
(6”)overtheentire lengthofthe heater plus25mm(1”) ateither
end.
16.Remove bottom front panelsecuring screws. These
were loosened in step 4 and should be easily unscrewed
byhand. 17. Pull bottom of front panel forward to disengage it from
bottomof heater.
22. Remove one element to allow access for the back row
of bricks. On the XL/XLS24N remove the element to the
right of centre, on the XL/XLS18N remove the central
element and on the XL/XLS12N remove the left hand
element. Loosen the two screws securing the element tails
in the ceramic block, and lift the element up and out of the
heater.
18. Still holding the bottom of front panel forward, lift
upwards to disengage top edge of front panel from groove
on heater toppanel 1, and remove front panel from heater
2.
19.Remove the protective polystyrene packing from
the front inner skin panel and discard. Remove screws
retaining front inner skin.
20. Carefully lift the bottom of the front inner skin panel out
of the retaining flange at the base of the heater, taking
care not to damage the insulation attached to this panel. 21. Remove the internal packing by sliding it up and off the
elements, taking care not to damage the insulation.
24. Replace the element which had been removed by
carefully passing the ends through the base insulation
slots into the terminal blocks below. Position the insulator
on the element end in contact with the terminal block
ceramic as shown, and tighten the connection screws. At
this point check that all element connections are tight.
25. Fit the front bricks with the airways facing inwards.
26. Re-fit the inner front panel/insulation assembly,
ensuring the bottom edge of the panel is located behind the
base flange. Make sure all screws removed in Operation
19are replacedsecurely.
27. Check that the damper mechanism within the heater
functions freely, by rotating the left hand control knob.
Check also that the right hand (input) knob rotates freely.
23. Position the bottom rear layer of bricks with the recess
over the slots in the base insulation slab. Push the bricks
firmly to the back of the heater, then fit the top row of
bricks.
28. Introduce mains supply cable through the cable clamp
into the terminal area, and connect in accordance with the
terminalmarkings. HEAT RESISTING CABLE MUST BE
USED (min. T85). Ensure that the cable is clamped so
that there is no excess cable in the terminal area. ON
NOACCOUNT SHOULDANYSURPLUSCABLE BE
PUSHED INSIDE OR BEHIND THE HEATER. CHECK
ALLELECTRICAL CONNECTIONS FOR TIGHTNESS.
GlenDimplex UK Limited
MillbrookHouse,
GrangeDrive,HedgeEnd,
Southampton SO30 2DF
30. Push the bottom of the front panel towards the heater,
so that the bottom flange locates under the base.
31. Replace the two front panel securing screws removed
in operation 16. A small mirror on the floor under the
heater will help location of the threaded holes in the base.
These should be tightened using an 8mm AF socket or
openendedspanner.
Ensure all screws have been fully tightened.
32. Ensuring the electricity supply is disconnected,
connect the free end of the mains cable to a suitable
double-pole switch adjacent to the appliance -
reinstate the electricity supply.
NOTE: The double pole switch must have a contact
separation of at least 3mm in all poles.
29. Holding the bottom edge of the front panel towards
you, locate the top edge of the front panel in the groove at
the top of the heater.
CustomerHelpLine 0870 7270 101
ProductSales 0870 7270 103
HeadOffice 08700777 117
e-mail customer[email protected]
Andere Handbücher für XL12N
1
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Dimplex Heizung Handbücher
Dimplex
Dimplex CPTS Bedienungsanleitung
Dimplex
Dimplex DHCERA15M Bedienungsanleitung
Dimplex
Dimplex RAL15-AU Bedienungsanleitung
Dimplex
Dimplex CTHK 630 Bedienungsanleitung
Dimplex
Dimplex WMCS712N Bedienungsanleitung
Dimplex
Dimplex DTX Series Installationsanleitung
Dimplex
Dimplex BS 120 Bedienungsanleitung
Dimplex
Dimplex DXLWP400TS Bedienungsanleitung
Dimplex
Dimplex XT12 Bedienungsanleitung
Dimplex
Dimplex DIR Series Bedienungsanleitung
Dimplex
Dimplex CEL50 Bedienungsanleitung
Dimplex
Dimplex CDE2TI Cadiz Eco Bedienungsanleitung
Dimplex
Dimplex RUG3TS Bedienungsanleitung
Dimplex
Dimplex DHCB20 Bedienungsanleitung
Dimplex
Dimplex FutuRad FutM2TSTi Bedienungsanleitung
Dimplex
Dimplex MFP 051E Bedienungsanleitung
Dimplex
Dimplex EVORAD2E Bedienungsanleitung
Dimplex
Dimplex CXLSN Bedienungsanleitung
Dimplex
Dimplex VERDI Bedienungsanleitung
Dimplex
Dimplex BLF7451 Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung