Dimplex BLF50 Bedienungsanleitung

Owner’s Manual

Model

BLF50

7210380100R03

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and tech-

niques that are considered impor-

tant enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ...................... 3

Important Instructions ........................... 4

Quick Reference Guide .......................... 7

Fireplace Installation ............................ 8

Site Selection ...................................... 8

Hardwire Installation ................................. 9

Wiring ............................................ 9

Surface Installation ................................. 12

In-wall Recessed Installation - 2x4 Framing .............. 14

Flush Mounted Installation - 2x8 Framing ............... 15

Front Glass Installation .............................. 17

Operation .................................... 18

Maintenance ................................. 21

Accessories .................................. 21

Warranty .................................... 22

Replacement Parts ............................ 24

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

Serial Number

Label Rating Label

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

using this electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces. The

surface around the heater outlet

becomes hot during heater opera-

tion.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not par-

tially or fully cover or obstruct the

front of this heater.

③Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended

for use by young children or

inrmed persons without supervi-

sion.

⑥Do no operate any heater

after it malfunctions. Disconnect

IMPORTANT INSTRUCTIONS

power at service panel and have

heater inspected by a reputable

electrician before reusing.

⑦ If the supply cord is dam-

aged, it must be replaced by the

manufacturer, or its service agent,

or a qualied person in order to

avoid a hazard. Contact Dimplex

Technical Service for obtaining a

replacement cord at

1-888-346-7539.

⑧ Do not use outdoors.

⑨Never locate replace where

it may fall into a bathtub or other

water container.

⑩ Do not locate the heater im-

mediately below a xed socket-

outlet.

⑪ To disconnect the replace,

turn the controls off, and turn off

power to heater circuit at main

disconnect panel.

⑫Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑬ To prevent a possible fire, do

not block air intakes or exhaust in

any manner.

⑭ A heater has hot and arcing or

sparking parts inside. Do not use

SAVE THESE INSTRUCTIONS

in areas where gasoline, paint,

or ammable liquids are used or

stored.

⑮ Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause fire,

electric shock or injury to persons.

⑯ To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will fit in a

polarized outlet only one way. If

the plug does not fit fully in the

outlet, reverse the plug. If it still

does not fit, contact a qualified

electrician to install the proper

outlet. Do not change the plug in

any way. Always plug heaters di-

rectly into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰Do not burn wood or other

materials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳Always use properly ground-

ed, fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒ When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

!NOTE: This equipment has been

tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

can radiate radio frequency energy

and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

· Increase the separation between

the equipment and the receiver.

· Connect the equipment into an

outlet on a circuit different from that

to which the receiver is connected.

· Consult the dealer or an

experienced radio/TV technician for

help.

Operation is subject to the following

two conditions: (1) this device may not

cause interference and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

IMPORTANT INSTRUCTIONS

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

Quick Reference Guide

Figure 1

① The electrical information

regarding your electric replace can

be found on the rating label located

on the front of the unit, behind the

glass.

Before installation, please record your

replace's serial number below for

future reference.

② If you have any technical

questions or concerns regarding the

operation of your electric replace,

or require service contact customer

service.

③ For dimensions of your replace,

refer to Figure 1.

3" (7.6 cm)

50 516" (128 cm)

19 12

(49.5 cm)

46" (116 cm)

48 12" (123 cm)

(17.8 cm)

3 1316"

(9.7 cm)

18"

(45.7 cm)

16"

(40.6 cm)

8 www.dimplex.com

Site Selection

Review and consider all of the fol-

lowing conditions for installation:

• Dimensions of the unit: 505/16"

(128cm) x 19½"(49.5cm)

• Unit requires a minimum of two

wall studs in order to ensure a

secure installation

Three possible installation meth-

ods:

• Surface mount (pg. 12); In-wall

Recessed (pg. 13); or Flush

mount (pg. 15)

• Hardwired or plug-in method

!NOTE:If the desired replace

location is on the interior of an

exterior wall the unit should only

be surface mounted. If a in-wall or

ush mount look is desired build

the interior wall out into the room.

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not essen-

tial in all cases. A dedicated circuit

will be required if, after installa-

tion, the circuit breaker trips or

fuse blows on a regular basis

when the heater is operating. Ad-

ditional appliances on the same

circuit may exceed the current

rating of the circuit breaker.

WARNING: Ensure the power

cord is not installed so that it is

Fireplace Installation

pinched or against a sharp edge

and ensure that the power cord

is stored or secured to avoid

tripping or snagging to reduce

the risk of re, electric shock or

injury to persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

1. Select a location that is not

susceptible to moisture and

is away from drapes, furniture

and high trafc.

2. For ease of electrical hook up

you may wish to locate the

replace near an existing outlet

(for plug-in convenience) (refer

to NOTE 1).

3. Remove replace, front glass

and hardware from box and

remove all packaging materials

before installation.

4. Store the replace in a safe,

dry and dust free location until

you are ready to install the

replace.

Fireplace Installation

Hardwire Installation

The replace is packaged with a

two prong plug installed for plug-

in convenience. Hard wiring the

replace is also an option for any

installation.

WARNING: Do not attempt to

wire your own new outlets or

circuits. To reduce the risk of

re, electric shock or injury to

persons, always use a licensed

electrician.

WARNING: Ensure that the

On/Off Switch is set to the Off

position (refer to Operation

section) and that the circuit

on which the replace is to be

installed has the power cut off at

the service panel until installa-

tion is complete.

1. Remove the partially reective

glass from the replace:

• Lay replace on its back.

Figure 2

Partially

Reective Glass

Glass Bracket

Bracket Screws

• Remove two Phillips screws

from each of the two glass

brackets (Figure 2).

• Remove glass brackets.

• With one hand keeping pres-

sure on the partially reective

glass, tilt the replace upright

and slightly forward to allow

the partially reective glass to

fall out of the inside framing.

Wiring

120V~

60Hz

RL3

RL2

RL1

LED LIGHTS

LED CONTROL

BOARD

10 www.dimplex.com

3. Remove one Phillips screw to

release the electrical box cov-

er in the bottom, right corner of

the replace (Figure 4).

4. Carefully remove the electrical

box cover from the replace

as wires are fed through the

strain reliefs on the cover and

are connected within.

CAUTION: Partially reective

glass is not tempered. Do not

bump or drop the partially reec-

tive glass to avoid breakage and

personal injury.

• Remove partially reective

glass from replace.

2. Remove six Phillips screws

that fasten the media tray and

two screws that fasten the

front panel tabs (Figure 3).

Carefully remove both compo-

nents.

Fireplace Installation

Figure 5 Wires to

controls

Wire connectors

Junction

Box screw

Figure 6

Junction Box screws (3)

Figure 4

Electrical box

Screw

Figure 3

Front Panel

Front Panel tabs (2)

Media Tray screws (2)

Andere Handbücher für BLF50

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex OS2527GB Bedienungsanleitung

Dimplex

Dimplex NARVIK NOVA Bedienungsanleitung

Dimplex

Dimplex Chadwick Suite CDW15WW Bedienungsanleitung

Dimplex

Dimplex SWM4220 Bedienungsanleitung

Dimplex

Dimplex SF3202 Bedienungsanleitung

Dimplex

Dimplex PF2325 Bedienungsanleitung

Dimplex

Dimplex OLF46-AM Bedienungsanleitung

Dimplex

Dimplex BF8000ST Bedienungsanleitung

Dimplex

Dimplex BEETHOVEN Bedienungsanleitung

Dimplex

Dimplex 5011139048455 Bedienungsanleitung

Dimplex

Dimplex COMPACT FIREPLACE Bedienungsanleitung

Dimplex

Dimplex Mini Mozart Bedienungsanleitung

Dimplex

Dimplex PRISM BLF3451-AU Bedienungsanleitung

Dimplex

Dimplex Pro Series Bedienungsanleitung

Dimplex

Dimplex EWMC-CC-SS Bedienungsanleitung

Dimplex

Dimplex CDFI1000P Bedienungsanleitung

Dimplex

Dimplex BLF34 Bedienungsanleitung

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Bedienungsanleitung

Dimplex

Dimplex BLF7451 Bedienungsanleitung

Dimplex

Dimplex CDN20-AU Bedienungsanleitung

Dimplex

Dimplex EF2870 Bedienungsanleitung

Dimplex

Dimplex EWF-SS Bedienungsanleitung

Dimplex

Dimplex Somerley SOM20 Bedienungsanleitung

Dimplex

Dimplex BLF5051-INT Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung