Dimplex DCF44GS Bedienungsanleitung

Owner’s Manual

Model

DCF44GS

To view the full line of Dimplex products, please visit

www.dimplex.com

7210050100R01

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are

considered important

enough to emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result

in damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations . . . . . . . . . . . . . . . . . . . 3

IMPORTANT INSTRUCTIONS ..................4

Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . 6

Site Selection and Preparation . . . . . . . . . . . . . . . . . 7

Operation...................................8

Maintenance...............................14

Warranty .................................16

ReplacementParts..........................19

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace. Model Number

Serial Number

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the electric replace.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation. Keep

combustible materials, such

as furniture, pillows, bedding,

papers, clothes, and curtains at

least 3 feet (0.9 m) from the front

of the unit.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Always unplug the electric

replace when not in use.

⑤Do not operate any unit with

a damaged cord or plug, or if

the heater has malfunctioned,

or if the electric replace has

been dropped or damaged in

any manner. Return heater

to authorized service facility

IMPORTANT INSTRUCTIONS

for examination, electrical or

mechanical adjustment, or repair.

⑥Do not use outdoors.

⑦ The electric replace is not

intended for use in bathrooms,

laundry areas and similar indoor

locations. Never locate heater

where it may fall into a bathtub or

other water container.

⑧Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc

area and where it will not be

tripped over.

⑨To disconnect the unit, turn

the controls off, then remove the

plug from the outlet.

⑩Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑪ To prevent a possible re, do

not block air intake or exhaust

in any manner. Do not use on

soft surfaces, like a bed, where

openings may become blocked.

⑫All electrical heaters have

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored or

where the unit will be exposed to

ammable vapors.

⑬Do not modify the electric

replace. Use it only as described

in this manual. Any other use

not recommended by the

manufacturer may cause re,

electric shock or injury to persons.

⑭Avoid the use of an extension

cord or power bar. Extension

cords and power bars may

overheat and cause a risk of re.

If you must use an extension cord

or power bar, it must be No. 14

AWG minimum size and rated for

no less than 1875 Watts.

⑮ Do not burn wood or other

materials in the electric replace.

⑯ Do not strike the replace

glass.

⑰ Always use a certied

electrician should new circuits or

outlets be required.

⑱Always use properly

grounded, fused and polarized

outlets.

⑲Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑳When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains small batteries.

Keep away from children. If

swallowed, seek medical attention

immediately.

WARNING: Do not install

battery backwards, charge, put

in re or mix with used or other

battery types - may explode or

leak causing injury.

!NOTE: Changes or

modications not expressly

approved by the party responsible

for compliance could void

user's authority to operate the

equipment.

6 www.dimplex.com

Quick Reference Guide

①Prior to the rst use of the

replace verify the following:

• Are the circuit breakers for the

unit on?

• Are the light bulbs in your

replace loose? (to check, follow

the instructions for replacing the

light bulbs under the Maintenance

section of this manual)

②The heater on your replace

may emit a slight, harmless odor

when rst used. This odor is a

normal condition caused by the

initial heating of internal heater

parts and will not occur again.

③The information regarding the

model of your replace can be

found on the rating plate located

on the top of the unit.

!NOTE: This equipment has

been tested and found to

comply with the limits for Class

B digital device, pursuant to

part 15 of the FCC Rules.

These limits are designed

to provide reasonable

protection against harmful

interference in a residential

installation. This equipment

generates, uses and can

radiate radio frequency

energy and, if not installed

and used in accordance with

the instructions, may cause

harmful interference to radio

or television reception, which

can be determined by turning

the equipment off and on, the

user is encouraged to try to

correct the interference by

one or more of the following

measures:

· Reorient or relocate the

receiving antenna.

· Increase the separation

between the equipment and

the receiver.

· Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

· Consult the dealer or an

experienced radio/TV

technician for help.

Operation is subject to the

following two conditions: (1)

this device may not cause

interference and (2) this device

must accept any interference,

including interference that may

cause undesired operation of

the device

Site Selection and Preparation

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A

dedicated circuit will be

required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when

the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that it

is pinched or against a sharp

edge and ensure that the

power cord is stored or

secured to avoid tripping or

snagging to reduce the risk

of re, electric shock or injury

to persons.

Construction and electrical

outlet wiring must comply with

local building codes and other

applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

always use a licensed

electrician.

This section provides instructions

for selecting a location and

preparing the site to install the

replace into your Dimplex mantel

surround.

①Select a suitable location that

is not susceptible to moisture and

is away from drapes, furniture and

high trafc.

②For ease of electrical hook

up you may wish to locate the

replace near an existing outlet

(refer to NOTE 1).

③ Store the replace in a safe

dry and dust free location.

!NOTE: The dimensions of

the replace are 44 inches

(1118 mm) wide X 34 inches

(883 mm) high X 11 5/8 inches

(295 mm) deep. The replace

does not require any additional

venting.

8 www.dimplex.com

Operation

Electric Fireplace Manual

Control

The manual controls for the

replace are located in the upper

right hand corner (Figure 1).

A. Main On/Off Switch

Supplies power to the 3 position

manual control switch.

B. 3 Position Manual Control

Switch

Remote (right position): The

unit is operated with the remote

control.

Flame (center position): The

ame effect is turned ON.

Flame & Heat (left position):

The ame effect and heater are

turned ON simultaneously. When

Figure 1

ABC

the manual control is in the Flame

& Heat position the heater does

not run on the remote operated

thermostat.

!NOTE: When the manual

control switch is in the Flame

and Flame & Heat positions,

the replace unit will not

operate with the remote

control.

C. Initialization Button

Used to synchronize the remote

control.

Resetting The

Temperature Cutoff

Switch

Should the heater overheat, an

automatic switch will turn the

heater off and it will not come

back on without being reset.

The temperature cutoff switch

can be reset by unplugging the

unit, waiting ve (5) minutes and

plugging the unit back in.

CAUTION: If you need to

continuously reset the

heater, unplug the unit and call

Dimplex North America Limited

Operation

at 1-888-346-7539 and press

4 for technical support. Please

have your model and serial

number ready when calling.

Remote Control

The remote control has a range of

approximately 50 feet

(15.25 m), it does not have to

be pointed at the replace and

can pass through most obstacles

(including walls). It is supplied

with 243 independent frequencies

to prevent interference with other

units.

Battery Installation

①Depress tab on the battery

cover on the back of the remote

transmitter and remove battery

cover (Figure 2).

Figure 2

Batteries

Child Lock

②Install two (2) AAA batteries

into the remote control (included).

③Ensure child lock is in the

“unlocked” position.

④Replace the battery cover.

!NOTE: When the “BAT”

symbol is present on the

remote control it is

recommended to replace the

batteries promptly, to maintain

full functionality of the remote/

replace. The remote

transmitter has a battery

backup time of only several

hours.

Battery must be recycled

or disposed of properly.

Check with your Local

Authority or Retailer for recycling

advice in your area.

Initializing/Reprogramming

The Remote Control

①Plug cord into 120 Volt wall

outlet.

②Ensure the Main On/Off

switch located in the switch box

on the replace in the upper

right hand corner is in the

position.

10 www.dimplex.com

Operation

③Set the 3 position manual

control to the Remote position

(right position).

④Press and hold the

initialization button on the unit.

⑤While holding the initialization

button, press the Flame/Heat ON/

OFF button on the remote

control transmitter.

⑥Release the initialization

button on the unit.

⑦ Press the Flame/Heat On/Off

button to turn the Flame/Heat

function ON.

Frequency Interference

If the replace does not respond

properly to the remote control,

the remote operating frequency

may have to be reset. The

remote control can send another

frequency code to the circuit

board to eliminate interference.

①Simultaneously press the

“Temperature Down” button and

the “Flame Speed Down” button

on the remote control.

②“COD” will appear in place of

the sleep timer digits.

③Release the “Temperature

Down” button and the “Flame

Speed Down” button.

④Press the initialization button

on the unit.

⑤Press the button on the

remote.

Your remote will now have a

different frequency

communicating with the replace.

Andere Handbücher für DCF44GS

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex BF33ST Bedienungsanleitung

Dimplex

Dimplex EF3003 Bedienungsanleitung

Dimplex

Dimplex THWG XLF50 Bedienungsanleitung

Dimplex

Dimplex VIANA DELUXE VNA20RC Bedienungsanleitung

Dimplex

Dimplex DWOP20R Bedienungsanleitung

Dimplex

Dimplex DF2608-INT Bedienungsanleitung

Dimplex

Dimplex BLF50 Bedienungsanleitung

Dimplex

Dimplex NAVARRA NAV15P PEBBLE Betriebsanleitung

Dimplex

Dimplex PF2325 Bedienungsanleitung

Dimplex

Dimplex Opti-Myst Cassette 500 Bedienungsanleitung

Dimplex

Dimplex WBK20 Bedienungsanleitung

Dimplex

Dimplex DFR2551G Bedienungsanleitung

Dimplex

Dimplex Optiflame MiniMozart FGA15E Bedienungsanleitung

Dimplex

Dimplex OAKHURST OKT20 Bedienungsanleitung

Dimplex

Dimplex BF33STP/DXP Bedienungsanleitung

Dimplex

Dimplex Juneau JUN Bedienungsanleitung

Dimplex

Dimplex Opti-V Bedienungsanleitung

Dimplex

Dimplex Marbello Bedienungsanleitung

Dimplex

Dimplex DF2624L-EUE Bedienungsanleitung

Dimplex

Dimplex BF 30' series Bedienungsanleitung

Dimplex

Dimplex EF2870L Bedienungsanleitung

Dimplex

Dimplex BLF74 Bedienungsanleitung

Dimplex

Dimplex BLF3451 Bedienungsanleitung

Dimplex

Dimplex DF2608 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung