Dimplex DF2690 Bedienungsanleitung

Owner’s Manual

Model

DF2690

6904411000

7208680200R08

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are considered

important enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ...................3

IMPORTANT INSTRUCTIONS .................4

Fireplace Installation ........................7

Operation .................................11

Maintenance ..............................14

Warranty .................................17

Replacement Parts .........................20

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

S E R IAL No.

MODE L

MOD.

4 www.dimplex.com

IMPORTANT INSTRUCTIONS

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the electric replace.

② The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the electric

replace when not in use.

⑤Do not operate any heater

after it malfunctions. Disconnect

power at the service panel and

have the heater inspected by a

reputable electrician before reus-

ing.

⑥ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

⑦ Do not use outdoors.

⑧ Never locate heater where it

may fall into a bathtub or other

water container.

⑨ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑩ Do not locate the heater

immediately below a xed socket-

outlet.

⑪ To disconnect the unit, turn

the controls off, then remove the

plug from the outlet.

⑫Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑬ To prevent a possible re, do

not block air intake or exhaust in

any manner.

⑭ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

⑮ Do not modify the electric

replace. Use it only as described

in this manual. Any other use not

recommended by the manufactur-

er may cause re, electric shock

or injury to persons.

⑯ Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰ Do not burn wood or other

materials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳Always use properly ground-

ed, fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒When transporting or storing

the unit and cord, keep in a dry

place, free from excessive vibra-

tion and store so as to avoid dam-

age.

WARNING: Remote control

contains small batteries. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

6 www.dimplex.com

!NOTE: This equipment has been

tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee

that interference will not occur in a

particular installation. If his equipment

does cause harmful interference to

radio or television reception, which

can be determined by turning the

equipment off and on, the user is

encouraged to try to correct the

interference by one or more of the

following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between

the equipment and the receiver.

• Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

• Consult the dealer or an

experienced radio/TV technician

for help.

This device complies with Part 15 of

the FCC Rules. Operation is subject

to the following two conditions:

(1) this device may not cause

interference and (2) this device must

accept any interference received,

including interference that may cause

undesired operation.

IMPORTANT INSTRUCTIONS

Fireplace Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

CAUTION: Clearance for air

circulation beneath the re-

place insert is provided by two

rubber feet.

Do not install the replace

insert directly on carpet or

similar surfaces which may

restrict air circulation.

CAUTION: If installing the

replace in a carpeted area, place

a one-piece, solid, at surface

under the replace. Ensure that

both of the feet rest securely on

this surface.

!NOTE: The dimensions of the

replace with the trim are 27 ⅜"

(695 mm) wide X 23 ½" (596 mm)

high X 8 3/4" (222 mm) deep.

Dimensions without trim are

26 ¼" (663 mm) wide X 22 ⅞"

(580 mm) high X 8 ¾" (222 mm)

deep. The replace does not

require any additional venting

(Figure 1).

Figure 1 27 ⅜”

(695 mm)

22 ⅞”

(580 mm)

23 ½”

(596 mm)

8 ¾”

(222 mm)

26 ¼”

(663 mm)

8 www.dimplex.com

Figure 3Figure 2

Foam

Block

Cable

Ties

Front

Glass

Trim

Track

Fireplace Installation

Fireplace Assembly

Depending on the unit, the front

glass will come packaged sepa-

rately or installed in the rebox.

1. Remove replace and glass

(if not already installed) care-

fully from the carton, discard

the plastic bag and foam

packaging.

2. Remove the right hand side

trim by removing four Phillips

screws at the side of the re-

place. (Figure 3)

3. Remove the front glass, if

necessary

4. Remove the foam block from

within the replace (Figure 2).

5. Using side cutters or scissors,

cut and remove the two cable

ties as shown in Figure 2 and

remove the cardboard that

protects the log set.

6. Place the Front Glass onto

the track of the replace (Fig-

ure 3) and slide it along the

front until it reaches the far

left of the unit.

7. Re-attach the right hand trim

piece using the four Philips

screws from step 4.

Mantel Installation

Install the replace assembly into

the mantel (refer to mantel as-

sembly instructions).

!IMPORTANT: If not using a

Dimplex mantel, the replace

Fireplace Installation

must be installed in an enclo-

sure with the following MINI-

MUM dimensions

(Figure 4).

New Wall Construction

8. Mark the desired location on

the oor.

9. Use studs to frame an open-

ing of 26 ¾" (679 mm) wide

X 23 ⅛" (587 mm) high X 9"

(229 mm) deep.

10. Plug the unit into a 15 Amp,

120 Volt outlet.

Option #1: The power cord can

be run from behind the trim and

along the wall to an outlet near

the replace.

Option #2: A new outlet can be

installed inside the framing con-

26 ¾”

(679 mm)

23⅛”

(587mm)

9”

(229 mm)

Figure 4 struction.

!NOTE: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A dedi-

cated circuit will be required

if after installation the circuit

breaker trips or fuse blows

on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating

of the circuit breaker.

Existing Fireplace

1. Seal all drafts and vents with

a non-brous insulation mate-

rial to prevent any chimney

debris from falling onto the

replace. Do not install into

an existing replace that is

prone to dampness.

2. Cap the top of the chimney

ue to prevent rain from

entering.

3. Plan your electric power sup-

ply.

4. The power cord can run along

the front of the hearth to an

outlet near the replace.

For Bathroom Use

If this unit is installed in a bath-

room it must be protected by

10 www.dimplex.com

Fireplace Installation

a GFI receptacle or circuit. If

receptacle is used it must be

readily accessible. To prevent

electrical shock this unit is an

electrical appliance that is not

watertight and must be installed

as to prevent water from entering

unit. This must be installed away

from showers, tubs, etc. Never

locate replace where it may fall

into a bathtub or other water con-

tainer. High temperatures may be

generated under certain abnormal

conditions. Do not partially or fully

cover or obstruct the front of this

heater.

SPEED

CONTROL

3 STAGE RECEIVER

ELEMENTS

BLOWER

MOTOR

LOWER

LIGHTS

UPPER

LIGHTS

DIMMER

FLICKER

MOTOR

CUT-OUT

THERMOSTAT

STAGE 1

STAGE 2

STAGE 3

Wiring

Andere Handbücher für DF2690

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex Vivente Plus V V T75 Handbuch

Dimplex

Dimplex CAS500R Bedienungsanleitung

Dimplex

Dimplex 30" FIREPLACE Bedienungsanleitung

Dimplex

Dimplex SP16 Bedienungsanleitung

Dimplex

Dimplex Michigan Fire MCN20 Bedienungsanleitung

Dimplex

Dimplex 7207380100REV00 Bedienungsanleitung

Dimplex

Dimplex BIZET BZT20 Bedienungsanleitung

Dimplex

Dimplex SNG20 Bedienungsanleitung

Dimplex

Dimplex Diamantique Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3015 Bedienungsanleitung

Dimplex

Dimplex STRAUSS STS20 Bedienungsanleitung

Dimplex

Dimplex milano-ef Bedienungsanleitung

Dimplex

Dimplex Juneau JUN Bedienungsanleitung

Dimplex

Dimplex 3-STEP Optimyst Bedienungsanleitung

Dimplex

Dimplex SWM4220 Bedienungsanleitung

Dimplex

Dimplex Crestmore CRS20 Bedienungsanleitung

Dimplex

Dimplex IN-STUD V1525BT Bedienungsanleitung

Dimplex

Dimplex TOLUCA TLC20 Bedienungsanleitung

Dimplex

Dimplex Auvergne Log 2920 Bedienungsanleitung

Dimplex

Dimplex ELBA Bedienungsanleitung

Dimplex

Dimplex 6908760100 Bedienungsanleitung

Dimplex

Dimplex purifire DF3220 Sseries Bedienungsanleitung

Dimplex

Dimplex VCX1525 Bedienungsanleitung

Dimplex

Dimplex 34" Prism Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch