Dimplex DWF3651 Bedienungsanleitung

Owner’s Manual

Model

DWF3651

7214040100R01

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .................3

IMPORTANT INSTRUCTIONS ............... 4

Quick Reference Guide .....................6

Fireplace Installation ......................7

Operation ...............................11

Maintenance ............................14

Warranty ...............................15

Replacement Parts .......................17

Welcome & Congratulations

Thank you and congratulations for purchasing an electric replace from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Rating Label with Model

Number and Serial Number

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before us-

ing the electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The trim around the heater outlet

becomes hot during heater opera-

tion.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the fireplace

when not in use.

⑤ Young children should be

supervised to ensure that they do

not play with the appliance.

⑥ The appliance is not intended

for use by young children or

inrmed persons without supervi-

sion.

⑦ If the supply cord is damaged,

it must be replaced by the manu-

facturer, or its service agent, or a

qualied person in order to avoid

a hazard.

⑧ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

IMPORTANT INSTRUCTIONS

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at

1-888-346-7539.

⑨Do not use outdoors.

⑩ This fireplace is not intended

for use in bathrooms, laundry ar-

eas and similar indoor locations.

Never locate heater where it may

fall into a bathtub or other water

container.

⑪ High temperature, keep electri-

cal cords, drapery, and other

furnishings at least 3 feet (0.9m)

from the front of the heater and

away from the side and rear.

⑫ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑬ Do not locate the unit directly

below a xed electrical conve-

nience outlet.

⑭ To disconnect the replace,

turn the controls off, then remove

the plug from the outlet.

⑮ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑯ Do not block air intake or

SAVE THESE INSTRUCTIONS

exhaust in any manner. Do not

use on soft surfaces, like a bed,

where openings may become

blocked.

⑰ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable liq-

uids are used or stored or where

the unit will be exposed to am-

mable vapors.

⑱ Do not modify the electric

replace. Use it only as described

in this manual. Any other use not

recommended by the manufactur-

er may cause re, electric shock

or injury to persons.

⑲ Avoid the use of an extension

cord. Extension cords may over-

heat and cause a risk of re. This

heater is not intended for use with

an extension cord. Plug the cord

directly into an appropriate wall

receptacle.

⑳ Do not burn wood or other ma-

terials in the electric replace.

㉑ Do not strike the replace

glass.

㉒ Always use a certied electri-

cian should new circuits or outlets

be required.

㉓ Always use properly grounded,

fused and polarized outlets.

㉔ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉕ When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains a small battery. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

19.7”

500 mm

21.6”

549 mm

43.0”

1092

31.4”

796

18.1”

459

5.7”

144

6.0”

152 mm

9.1”

230 mm

36.0”

915 mm

43.0”

1092 mm

2.1”

53 mm

1.0”

25 mm

Quick Reference Guide

Figure 1

1. Before using the fireplace

verify the circuit breakers for

the unit on?

2. If you have any technical

questions or concerns

regarding the operation of

your electric fireplace, or

require service, contact

customer service.

3. The heater may emit a slight,

harmless odor when first

used. This odor is a normal

condition caused by the initial

heating of internal heater

parts.

4. For dimensions of your

replace, refer to Figure 1.

!NOTE: The use of feet are optional.

Site Selection

The unit is packaged with two

types of mounting options:

• Wall mounting, Surface

• Support feet, table top

!NOTE: A 15 Amp, 120 Volt cir-

cuit is required. A dedicated circuit

is preferred but not essential in all

cases. A dedicated circuit will be

required if, after installation, the

circuit breaker trips or the fuse

blows on a regular basis when the

heater is operating. Additional ap-

pliances on the same circuit may

exceed the current rating of the

circuit breaker.

WARNING: Ensure the power

cord is not installed so that it

is pinched or against a sharp

edge and ensure that the pow-

er cord is stored or secured to

avoid tripping or snagging to

reduce the risk of re, electric

shock or injury to persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

Fireplace Installation

shock or injury to persons,

always use a licensed electri-

cian.

WARNING: The supplied

mounting bracket is designed

for use with Dimplex wall

mounted replaces only. Im-

proper use, or use for purpos-

es other than intended, may

cause damage or injury.

Wall Mounting Instructions

WARNING: Failure to install

the replace as instructed

below may result in damage

to the equipment and or may

expose the user to the risk of

re, serious injury, illness or

death.

WARNING: The replace

requires the wall mounting

bracket screws to be installed

into a minimum of two wall

studs (Figure 2).

Tools Required

• #2 Phillips screwdriver

• Pencil

• Slot screwdriver

• Bubble level (supplied)

• Drill, and drill bits as required

Approximate time: 30 minutes

for installation

1. Select an appropriate location

8 www.dimplex.com

Fireplace Installation

to mount the unit on a wall,

above an electrical outlet.

Access to the electrical outlet

must be maintained. Ensure

the installation meets the

national and state/provincial

electrical codes.

!NOTE: It is recommended

that the bottom of the unit not be

mounted higher than 1020mm

(40") from the Fireplace Installa-

tion ground to maintain an opti-

mized viewing angle of the ame.

CAUTION: Ensure that the top

of the unit is at least 610mm

(24") from the ceiling or any

object (i.e. Electrical recep-

tacles) that may obstruct or be

susceptible the ow or tem-

perature of air out of the unit.

CAUTION: High temperature,

keep electrical cords, drapery,

and other furnishings at least

3 feet (0.9m) from the front of

the heater and away from the

side and rear.

2. The wall-mounting bracket

must be mounted to at least

2 wall studs. Studs should be

accessed through 2 wall-

bracket holes in one of the

following combinations: A&F,

B&D, or C&E (Figure 2).

!NOTE: Wall anchors must

be installed in the appropriate

wall locations to fasten the wall

bracket through the remaining

holes (Figure 3). For example, if

you plan to secure the bracket to

studs through holes A&D, install

anchors centered on holes B & C.

3. Hold the wall-mounting

bracket on the wall and mark

the location of 1 of the mount-

ing holes.

4. Place the bubble level onto

the top of the wall-mounting

Figure 2

Figure 3

40"

(102 cm)

Recommended

24"

(61 cm)

MINIMUM

32"

(81.3 cm)

MINIMUM

10. Install the remaining screws

through the bracket and into

the wall studs as required.

!NOTE: At least two of the

mounting screws must be in-

stalled into a wall stud.

11. Mount the unit on the wall,

so that the tabs on the wall

bracket have been inserted

into the slots on the back of

the rebox, as shown. (Figure

12. Carefully pour and evenly dis-

tribute the supplied glass rock

media in the Media tray of the

rebox (Figure 6).

13. Hang the front glass assembly

on the mounts of the rebox

and secure the glass onto the

unit by installing the retaining

screws (Figure 7).

14. Excess electrical cord can be

bracket.

5. Adjust the wall-mounting

bracket so the bubble on the

level is centered between the

two black lines.

6. Mark 3 other mounting screw

locations, on the wall, ensur-

ing that the wall bracket stays

level.

7. Install the supplied wall an-

chors on the drywall marked

locations by placing a #2 Phil-

lips screwdriver into the recess

of the anchor.

8. Press the anchor into the wall

in the desired marked posi-

tion while turning the anchor

clockwise until it is ush with

the wall.

9. Insert the wall anchor screws

through the wall bracket and

thread into the wall anchors.

Tighten the screw (Figure 4).

Fireplace Installation

Figure 5

Wall anchor

Screw

Wall

bracket

Figure 4

10 www.dimplex.com

Fireplace Installation

Media Tray

Front Glass

Assembly

Figure 7

Figure 6

inserted back into the bottom

of the unit, into the cord stor-

age area.

Support Feet Installation

Instructions

1. Remove unit from packaging

and place open side up on a

at working surface.

2. Secure the two support feet

to the bottom of the unit using

the supplied screws.

3. Turn the unit upright.

4. Attach the provided cover

plates over the two hanging

bracket openings on the back

of the unit, with the provided

screws (Figure 8).

5. Carefully pour and evenly dis-

tribute the supplied glass rock

media in the Media tray of the

rebox (Figure 6).

6. Hang the front glass assembly

on the mounts of the rebox

and secure the glass onto the

unit by installing the retaining

screws (Figure 7)

7. Excess electrical cord can be

inserted back into the bottom

of the unit, into the cord stor-

age area.

Glass Retaining

Screw

Figure 8

Cover Plates

Andere Handbücher für DWF3651

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex OS2527GB Bedienungsanleitung

Dimplex

Dimplex EWMC-CC-SS Bedienungsanleitung

Dimplex

Dimplex Michigan Fire MCN20 Bedienungsanleitung

Dimplex

Dimplex HAR20 Bedienungsanleitung

Dimplex

Dimplex RITZ20W Bedienungsanleitung

Dimplex

Dimplex 690932 Series Bedienungsanleitung

Dimplex

Dimplex PF3033 Bedienungsanleitung

Dimplex

Dimplex Atherton ATH20-INT Bedienungsanleitung

Dimplex

Dimplex SP1 Wallfire Bedienungsanleitung

Dimplex

Dimplex THWG XLF50 Bedienungsanleitung

Dimplex

Dimplex PRISM BLF3451-AU Bedienungsanleitung

Dimplex

Dimplex DF2600 Bedienungsanleitung

Dimplex

Dimplex DCF7850 Bedienungsanleitung

Dimplex

Dimplex CHADWICK CDW15XHD Bedienungsanleitung

Dimplex

Dimplex Cavendish CSH20 Bedienungsanleitung

Dimplex

Dimplex Opti-myst Bedienungsanleitung

Dimplex

Dimplex CAS500R-RGB-EU Bedienungsanleitung

Dimplex

Dimplex EWM-COPPER Kurzanleitung

Dimplex

Dimplex Atherton ATH20 Bedienungsanleitung

Dimplex

Dimplex Dakota DKT20 Bedienungsanleitung

Dimplex

Dimplex DF2624L-INT Bedienungsanleitung

Dimplex

Dimplex DF2603 Bedienungsanleitung

Dimplex

Dimplex OLF46-AM Bedienungsanleitung

Dimplex

Dimplex DFO2307 Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch