Dimplex ELECTRALOG CFP3913 Bedienungsanleitung

Owner’s Manual

Model

CFP3913

DFP18-1041

DFP18-1046

DFP18-1069

7209260100R06

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are considered

important enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .................3

IMPORTANT INSTRUCTIONS ...............4

Fireplace Installation .......................7

Operation ................................8

Maintenance .............................9

Warranty ...............................11

Replacement Parts ........................14

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result

in a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

Model Number

Serial Number

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the electric replace.

②This heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation. Keep

combustible materials, such

as furniture, pillows, bedding,

papers, clothes, and curtains at

least 3 ft (0.9 m) from the front of

the heater and keep them away

from the sides and rear.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the heater when

not in use.

⑤Do not operate any heater

after it malfunctions. Disconnect

power at the service panel and

have the heater inspected by a

reputable electrician before reus-

ing.

IMPORTANT INSTRUCTIONS

⑥ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

⑦ Do not use outdoors.

⑧ This heater is not intended for

use in bathrooms, laundry ar-

eas and similar indoor locations.

Never locate this heater where

it may fall into a bathtub or other

water container.

⑨ Do not run cord under carpet-

ing. Do not cover cord with throw

rugs, runners, or the like. Arrange

cord away from trafc area and

where it will not be tripped over.

⑩ To disconnect heater, turn

controls to off, then remove plug

from outlet.

⑪ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage the heater.

⑫ To prevent a possible re, do

not block air intakes or exhaust in

any manner.

⑬ All electrical heaters have

SAVE THESE INSTRUCTIONS

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

⑭ Do not modify the heater.

Use it only as described in this

manual. Any other use not recom-

mended by the manufacturer may

cause re, electric shock, or injury

to persons.

⑮ To reduce the risk of electric

shock, this heater has a polarized

plug (one blade is wider than the

other). This plug will t in a polar-

ized outlet only one way. If the

plug does not t fully in the outlet,

reverse the plug. If it still does not

t, contact a qualied electrician

to install the proper outlet. Do not

change the plug in any way.

⑯Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰ Do not burn wood or other

materials in the Fireplace.

⑱ Do not strike the front glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳ Always use properly grounded,

fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

heater.

㉒ When transporting or storing

the heater and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

6 www.dimplex.com

IMPORTANT INSTRUCTIONS

!NOTE: This equipment has been

tested and found to comply with the limits

for Class B digital device, pursuant to

part 15 of the FCC Rules. These limits

are designed to provide reasonable

protection against harmful interference in

a residential installation. This equipment

generates, uses and can radiate radio

frequency energy and, if not installed and

used in accordance with the instructions,

may cause harmful interference to radio

or television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet

on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Operation is subject to the following

two conditions: (1) this device may not

cause interference and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

CAUTION: Changes or

modications not expressly

approved by the party responsible

for compliance could void user's

authority to operate the equipment.

Fireplace Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

CAUTION: High temperature,

risk of re, keep electrical cords,

drapery, furnishings, and other

combustibles at least 3 ft (0.9 m)

from the front of the heater.

!NOTE: A 15 Amp, 120 Volt

alternating current (VAC) circuit

is required. A dedicated circuit

is preferred but not essential in

all cases. A dedicated circuit will

be required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating of

the circuit breaker.

1. Make sure the unit’s

3-Position Switch is switched

OFF ("O") (refer to operating

instruction section).

2. Plug the unit into a 15

Amp/120 VAC outlet.

CONTROL RECEIVER

REMOTE

FLICKER

MOTOR

SWITCH

3-POSITION

SWITCH

LOW HEAT SWITCH

HIGH HEAT

MOTOR

THERMAL

CUTOUT

ELEMENT

CAPACITOR

LOWER

LIGHTS

Wiring

8 www.dimplex.com

Operation

WARNING: This electric

rebox must be properly installed

before it is used.

Manual Controls

Three switches provide a choice

of heat settings. A switch is in the

ON position when the side with

the markings on (i.e. I, II, or II) is

pushed in. (Figure 1)

Switch 1

(I) Manual mode: Controls the

electricity supply to the heater

and ame manually.

(II)Remote mode: Allows the

control of electricity supply to

the heater and ame through

the use of the supplied remote

control.

!NOTE: This switch must

be in either (I) or (II) to operate

with or without heat.

Switch 2 (I) Provides 715 Watt

heat output.

Switch 3 (II)Provides 1430 Watt

heat output with Switch 2.

Remote Operation

The replace is supplied with an

integral ON/OFF remote control.

!NOTE: Ensure that the

replace 3-Position is set to the

remote control setting (i.e. II).

To operate: push ON button

to turn replace on; push OFF

button to turn replace off.

!NOTE: Remote control

operates main power supply.

Heat must still be controlled by

switches on replace.

Resetting The Tempera-

ture Cutoff Switch

Should the heater overheat, an

automatic cut out will turn the

heater off and it will not come

back on without being reset. It

can be reset by switching the

3-Position Switch to OFF ("O")

and waiting ve (5) minutes

before switching the unit back on.

Figure 1

3 2 1

Maintenance

 WARNING: Disconnect power

before attempting any main-

tenance or cleaning to reduce

the risk of re, electric shock or

damage to persons.

!NOTE: The replace should

not be operated with an accumu-

lation of dust or dirt on or in the

unit, as this can cause a build up

of heat and eventual damage.

For this reason the heater must

be inspected regularly, depending

upon conditions and at least at

yearly intervals.

Bulb Replacement

The bulbs are located behind the

back panel.

To gain access to the bulbs:

1. Remove the silver screw that

secures the access panel to

the rebox as indicated in

Figure 2.

2. Remove and slide out panel.

3. Remove the defective lamp

by unscrewing it as shown in

Figure 3.

4. Replace with a 60 Watt E12

clear chandelier or candela-

bra. Take care not to over-

tighten the bulb.

5. Ret the access panel and

secure with the screw re-

moved in step 1.

!NOTE: To remove the rebox

insert prior to repair, remove the

ve black screws at the back of

the rebox as shown in Figure 2

and slide it out to the front.

Helpful Hints: It is a good idea to

replace all light bulbs at one time

if they are close to the end of their

rated life. Group replacement will

reduce the number of times you

CAUTION: If you need to

continuously reset the heater,

unplug the unit and call customer

service at 1-888-346-7539.

Operation

10 www.dimplex.com

Maintenance

Figure 2

Access

Panel

Screw

Firebox Mounting

Screws (2)

Firebox

Mounting

Screws (3)

Figure 3

Bulbs

need to open the unit to replace

light bulbs.

Cleaning

WARNING: Always discon-

nect from the power supply

before cleaning the replace.

For general cleaning use a soft

clean duster – never use abra-

sive cleaners. The glass viewing

screen should be cleaned care-

fully with a soft cloth. DO NOT

use glass cleaners.

To remove any accumulation of

dust or uff the soft brush attach-

ment of a vacuum cleaner should

occasionally be used to clean the

outlet grill of the fan heater.

Servicing

Except for light bulb replacement

and cleaning described above, an

authorized service representative

should perform any other

servicing.

Andere Handbücher für ELECTRALOG CFP3913

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex DF2426GB Bedienungsanleitung

Dimplex

Dimplex FABER ALBANY ECO ABN15 ECO Bedienungsanleitung

Dimplex

Dimplex DFP6975O Bedienungsanleitung

Dimplex

Dimplex RLG20BR Bedienungsanleitung

Dimplex

Dimplex 23" Insert Fireplace DFPI2311 Kurzanleitung

Dimplex

Dimplex DF2426GB Bedienungsanleitung

Dimplex

Dimplex OS2527GB Bedienungsanleitung

Dimplex

Dimplex Toluca Deluxe Bedienungsanleitung

Dimplex

Dimplex ALBANY ECO Technisches Handbuch

Dimplex

Dimplex Optimyst 3STEP-RGB-EU Bedienungsanleitung

Dimplex

Dimplex GDS23L8-1904GB Bedienungsanleitung

Dimplex

Dimplex Avola AVA20 Bedienungsanleitung

Dimplex

Dimplex DFOP25 Bedienungsanleitung

Dimplex

Dimplex Charlotte CRT20BR Bedienungsanleitung

Dimplex

Dimplex BF33STP/DXP Bedienungsanleitung

Dimplex

Dimplex SAHARA FIREPLACE 6903950000 Bedienungsanleitung

Dimplex

Dimplex CFP4949BW Bedienungsanleitung

Dimplex

Dimplex ENG56-400 Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3215 Bedienungsanleitung

Dimplex

Dimplex Optiflame Toluca Deluxe TLC20LX Bedienungsanleitung

Dimplex

Dimplex 6911540100 Bedienungsanleitung

Dimplex

Dimplex Optiflame BF3600 Bedienungsanleitung

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Bedienungsanleitung

Dimplex

Dimplex BOF4056 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung