Dimplex Silverton SVT20 Bedienungsanleitung
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
08/52130/0 Issue 1
SILVERTON
SVT20
Table of Contents
Welcome and Congratulations ..................................................... 2
Important Instructions ................................................................... 3
Site Selection and Preparation ..................................................... 4
Log Grate Assembly...................................................................... 6
Log Grate Installation................................................................... 11
Operation .................................................................................... 12
Maintenance ............................................................................... 13
Additional Information ................................................................. 14
Troubleshooting .......................................................................... 15
Always use a qualied technician or service agent to repair this Log grate
Note: Procedures and techniques that are considered important enough to emphasise
Caution: Procedures and techniques which, if not carefully followed, will result in damage to the
equipment
Warning: Procedures and techniques which, if not carefully followed, will expose the user to risk
of re, serious injury or death.
The sump and the water tank in this product are treated with a biocidal product, Silver Biocide.
This conforms with the latest relevant ISO standard
1
Welcome and Congratulations
Thank you and congratulations for choosing to purchase a Silverton from Dimplex.
Please carefully read and save these instructions.
Caution: Read all instructions and warnings carefully before starting installation. Failure to follow
these instructions may result in a possible electric shock, re hazard and will void the warranty
Please record your model and seriel number below for future reference: model and serial number
can be found on the Model and Serial Number Label located on the side of the Silverton
Model Number: _________________
Serial Number: __________________
2
Important Instructions
Please read this information guide carefully to be able to safely install, use and maintain your
product
When using electrical appliances, basic precautions should always be followed to reduce the risk
of re, electrical shock and injury to persons, including the following:
1. WARNING
Do not place material or garments on, or obstruct the air circulation around the appliance.
2. DAMAGE
If the appliance is damaged, check with the supplier before installation and operation.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a
similarly qualied person in order to avoid a hazard.
3. LOCATION
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the re immediately below a xed socket outlet or connection box.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre
from the appliance.
4. PLUG POSITIONING
The appliance must be positioned so that the plug is accessible.
Keep the supply cord away from the front of the appliance.
5. UNPLUGGING
In the event of a fault unplug the device.
Unplug the device when not required for long periods.
6. OWNER/USER
This appliance is not intended for use by persons (including childing) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
7. ELECTRCITY
Before switching on, please read the safety advice and operating instructions.
Note: This appliance is only to be used with the power supply unit provided.
Only plug this appliance into a supply that corresponds to that displayed on the power supply
unit. The appliance must only be supplied at extra low voltage corresponding to the markings on
the appliance
CAUTION - Some parts of this product can become very hot and cause burns. Particular attention
has to be given where children and vulnerable people are present.
8. USAGE
Do not burn wood or other materials in the log grate
3
Site Selections and Preparation
This section provides instructions for selecting a location and preparing the site to install the Log
Grate
1. Select a suitable location that ensures the Log Grate is sitting on a hard level surface for
optimum ame effect
2. Allow for approximately 5cm of clearance behing the unit ( from the frame to the back of the
mantle) and 20cm directly above the back log to allow for removal of the Rell Container.
3. Carefully unpack all of the components from the box.
Caution: Handle the logs carefully, that are fragile and can easily crack or break if dropped.
4
1
3
2
4
5
6
7
4. Unpack the transducer (contained within the water reservoir) which has been wrapped to protect
it during shipping. See Figure 1.
To access the transducer;
• Remove the top cover by turning the retaining tabs on both ends of the water reservoir.
• Remove any packaging material.
• Install the transducer so that it is sitting level in the circular holding area in the resevoir.
• Orientate the transducer wire so that it does not sit directly above the Emitter and the wire
passes through the slit in the side of the tank.
• Reinstall the top cover and ensure both retaining tabs have been turned so that they are pointing
inwards.
Note: Completely assemble the unit before lling the water
5
Log Grate Assembly
Caution: Handle logs carefully, they are fragile
and can easily crack or break, if dropped.
6
Each log is a separate component that needs to be placed on the grate. Position each log so that
the hook and loop pad on the backside of the log lines up with the corresponding hook and loop
pad on the log grate. These pads assist with securing the logs to the grate.
Note: Each of these logs are hand made, and as such, the hook and loop pads on the logs and
grate may not align perfectly, therefore, we have included additional pads should you need to
reposition them.
Each of the logs contain LED lights to create a ickering effect. During the assembly, each log
requires the electrical connectors on the log and grate to be connected as they are being placed.
In some cases, these wires can have tie wraps added to prevent the wires from being seen after
nal assembly. (not included)
7
Log Grate Assembly
8
Log Grate Assembly
9
Log Grate Assembly
Andere Handbücher für Silverton SVT20
2
Inhaltsverzeichnis
Andere Dimplex Kamin im Innenbereich Handbücher
Dimplex
Dimplex JAZ20N Bedienungsanleitung
Dimplex
Dimplex VCX1525-EU Bedienungsanleitung
Dimplex
Dimplex Opti-Myst Cassette 500 Bedienungsanleitung
Dimplex
Dimplex SCANDIC Bedienungsanleitung
Dimplex
Dimplex Optiflame Electric Fireplace Bedienungsanleitung
Dimplex
Dimplex DF2608 Bedienungsanleitung
Dimplex
Dimplex DWF1146GP Bedienungsanleitung
Dimplex
Dimplex Revillusion RBF24DLX Bedienungsanleitung
Dimplex
Dimplex DF2010-EU-E Bedienungsanleitung
Dimplex
Dimplex Vivente Bedienungsanleitung
Dimplex
Dimplex THWG XLF50 Bedienungsanleitung
Dimplex
Dimplex DWF36-PG Bedienungsanleitung
Dimplex
Dimplex BELLINI BLN15W Bedienungsanleitung
Dimplex
Dimplex VCX1525 Bedienungsanleitung
Dimplex
Dimplex Modini DEC20M Bedienungsanleitung
Dimplex
Dimplex Revillusion Osbourne Bedienungsanleitung
Dimplex
Dimplex Pro Series Bedienungsanleitung
Dimplex
Dimplex EWM-COPPER Bedienungsanleitung
Dimplex
Dimplex Optimyst DFI400LH Bedienungsanleitung
Dimplex
Dimplex VVT75 Bedienungsanleitung
