Dinsafer Nova Pro Bedienungsanleitung

LAN + WiFi + Cellular

Smart Home Alarm System

User Manual

P15

P16

●Introduction

●Notice

●Safety

●Requirements

●System Status & User Authorities

●Appearance

●Setup

●App operation introduction

●FAQ

●Specifications

Table of Content

Introduction

• Thank you for purchasing the Nova Pro Smart Alarm System. Nova Pro oers you a complete control over your home security and

automation via your smartphone. This manual will guide you through the setup procedures and highlight some key features.

• The system operates on smartphones.

• Please note that all contents listed here might be slightly dierent from the contents of the package or the App. Please check the latest

version of the user manual.

• Version: V1.0

Notice

• All sensors and devices in the package have already been paired with the panel before shipping. Users can start using the whole system aer

setting up the network. Accessories purchased separately (like sensors or smart devices) need to be paired with the system for proper use.

• The system is designed for easy setup. If any problem occurs during the setup, please contact your distributor for help.

• Please store all manuals, nameplates and stickers with QR codes or barcodes for further use.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

7KHGLVWDQFHEHWZHHQXVHUDQGGHYLFHVKRXOGEHQROHVVWKDQFP

Safety

• This system is designed to minimize majority of risks and to ensure the safety of your home, however it does not guarantee protection

against burglary, robbery, the, or any type of emergencies. Users should continue to act prudently to protect the security of their lives and

property.

• Any alarm system is subject to compromise or failure for a variety of reasons as follows:

- An intruder may gain access through unprotected openings.

- An intruder may have the technical sophistication to bypass a sensor or the whole system.

- Signals sent by the panel or sensors may be blocked or reflected without being received, and a block may occur if metal objects are placed

into the path of the signal.

- Motion sensors can only detect the intrusion within the specified ranges and unobstructed areas.

- Malfunction of routers, limited services by wireless phone carriers or internet service providers, limited service such as text messages or push

notification provided by smartphone makers.

- Component failures or some other faults happen in the electrical system.

Requirements

• Wired/Wireless Router compatible with Wi-Fi IEEE 802.11 b/g/n standard

• Provision of Internet Service

• Mobile phone SIM card (supporting GSM/WCDMA/LTE)

• iPhone or Android smartphone

• iOS version 7.0 or higher

• Android version 4.3 or higher

• Bluetooth 4.2 or higher

System Status & User Authorities

• The Nova Pro system does not support any wired sensors. The panel communicates with all sensors via wireless RF signals. Most of the

sensors have low battery warning features. In the event of low battery, notifications will be sent to the APP. Smoke detector and CO sensor

work at full time.

• The system can set its security status according to the commands given by users or the signals sent from the triggered sensors.

- ARM:

All working sensors can be

triggered. The system will

generate alarms when receiv-

ing alert signals sent from

sensors.

- DISARM:

This mode will de-activate all

sensors. This mode will also

turn o the siren and stop the

alarm process.

- HOME ARM:

This mode will allow some

selected sensors to remain

working while others are de-

activated. These sensors can

be selected in App.

- SOS:

This mode will trigger built-in

siren and send alarm messag-

es to emergency contacts. It

also triggers external sirens or

other sensors like smart plugs.

- There are there levels of user authorities, shown as below.

- ADMINISTRATOR:

Who can fully control the system

and invite other users with assigned

authorities.

- USER:

Who can operate ARM/DISARM/HOME

ARM/SOS, control the smart plugs and

cameras, can also invite other people

as USER or GUEST.

- GUEST:

Who can only operate

ARM / DISARM / HOME ARM.

Power

Ethernet SIM Slot

Buzzer

• Rear View

Indicator

STATUS LED INDICATION

Operation Light ON ARM/DISARM/HOME ARM/SOS.

Setting Fast Blinking

Network Configuration

Reseting

Updating

Faults Slow Blinking

Low Battery

Network Fault

Other Faults

Appearance

• Top View

Wall Mounting Bracket

Siren

Battery Cover

Network Configuration Button

Power Switch

Reset Button

• Bottom View

Standard SIM

card adapter

Nano-SIM Micro-SIM

Setup

• Internet Connection Requirements

- Please ensure the router you are using has already been connected to the Internet with DHCP mode enabled. Nova Pro supports IPV4

protocol only.

- The system supports the following types of connection:

- LAN: 10/100M Ethernet.

- Wi-Fi: 2.4GHz, WEP/WPA/WPA2 encrypted.

• Place the Panel at a Suitable Place

- If Wi-Fi is used to connect the panel to internet, please make sure the panel is placed under Wi-Fi coverage before installation. (It is

recommended to use your phone to help verify the Wi-Fi coverage at the spot.

• Install the SIM Card (Optional)

- Insert a standard SIM card. Please place the Nano-SIM or Micro-SIM to a card adapter for installation.

• Get Ready for Setup

- Download the “Nova Pro” APP from either iOS APP Store or Google Play by searching “Nova Pro”, or scan the

QR code below with your mobile phone.

- Please open the lid on the back of the device, and turn on the power button. The indicator on the panel will

flash and aer approximately 45 seconds a beep sound should occur indicating the device being activated.

Make sure the Bluetooth is activated on your phone and place the panel close to 2.4GHz Wi-Fi signal.

• Add the Panel

- Make sure your mobile phone is connected to the Internet. Open the APP, click

on “Add a new device”

• Set Up Password

- APP will automatically scan for panels available nearby and display their names for which you can choose to connect. Aer successfully

connecting the panel, please rename the device and setup a password for future configuration purpose.

• Configure the Wi-Fi Setting of the Panel

- Select the Wi-Fi you want the panel to connect with and input the password to finish setup.

• Check Setting

- Make sure your mobile phone has been connected to the Internet via cellular or Wi-Fi.

- Try pressing ARM/DISARM button in the App, to see if the status icon would be changed accordingly.

- Try using remote control, pressing ARM / DISARM button to see if the status icon in the App would be changed accordingly.

• Installation

- Close the battery cover.

- Place the panel on a desktop or using the bracket to mount it on the wall.

Inhaltsverzeichnis

Andere Dinsafer Sicherheitssystem Handbücher

Dinsafer

Dinsafer DHW01O Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung