Direct Air RG52A2/BGCEF Bedienungsanleitung

CR070-RG52A2

202055091436

AIR CONDITIONER

REMOTE CONTROLLER ILLUSTRATION

Thank you very much for purchasing our air conditioner.

Please read this owner's manual carefully before using

your air conditioner.

The design and specifications are subject to change without prior notice for

product improvement. Consult with the sales agency or manufacturer for

details.

CONTENTS

Use the remote controller within a distance of 8

meters from the appliance, pointing it towards the

receiver. Reception is confirmed by a beep.

Location of the remote controller.

CAUTIONS

The air conditioner will not operate if curtains, doors or other materials

block the signals from the remote controller to the indoor unit.

Prevent any liquid from falling into the remote controller. Do not expose

the remote controller to direct sunlight or heat.

If the infrared signal receiver on the indoor unit is exposed to direct

sunlight, the air conditioner may not function properly. Use curtains to

prevent the sunlight from falling on the receiver.

If other electrical appliances react to the remote controller. either move

these appliances or consult your local dealer.

The remote controller is powed by two dry batteries(R03/LR03X2) housed in the

rear part and protected by a cover.

(1) Remove the cover by pressing and sliding off.

(2) Remove the old batteries and insert the new batteries,placing the(+) and (-)

ends correctly.

(3) Reattach the cover by sliding it back into position.

NOTE: When the batteries are removed, the remote controller erases all progra-

mming. After inserting new batteries, the remote controller must be reprogrammed.

Replacing batteries

Handling the remote controller

Keep the remote controller where its signals can

reach the receiver of the unit. When you select the

timer operation, the remote controller automatically

transmits a signal to the indoor unit at the specified

time. If you keep the remote controller in a position

that hinders proper signal transmission, a time lag of

up to 15 minutes may occur.

CAUTIONS

Do not mix old and new batteries or batteries of different types.

Do not leave the batteries in the remote controller if they are not

going to be used for 2 or 3 months.

Do not dispose batteries as unsorted municipal waste. Collection of such

waste separately for special treatment is necessary.

Handling the remote controller ......................................................

Remote controller Specifications...................................................

Function buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons .................................................................

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Adjusting air flow direction............................................................

Timer operation...............................................................................

SLEEP/FRESH function..................................................................

Model

Rated Voltage

8m (when using 3.0 voltage, it gets 11m)

3.0V(Dry batteries R03/LR03 2)

Remote Controller Specifications

1. Operating Mode: AUTO, COOL, DRY, HEAT(enabled on cooling& heating

models only ) and FAN.

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range : 17 C~30 C.

4. Full function of LCD (Liquid Crystal Display).

Environment

Signal Receiving

Range

Performance Feature

3344

RG52A2/BGCEF RG52A2/BGEF RG52A3/BGCEF RG52A3/BGEF

-5 C 60C

Function buttons

ON/OFF ON/OFF

MODE MODE

FAN FAN

TEMP TEMP

SHORT

CUT SHORT

CUT

TIMER ON TIMER ON

TIMER OFF TIMER OFF

SLEEP SLEEP FRESH

LED FOLLOW ME LED FOLLOW ME

TURBO SELF CLEAN TURBO SELF CLEAN

Each time the button is pressed, the operation

mode is selected in a sequence of following:

MODE Button

ON/OFF Button

Operation starts when this button is pressed

and stops when this button is pressed again.

NOTE: Heat mode is for Cooling & Heating models only.

AUTO

COOL

DRY

HEAT FAN

SELF CLEAN Button

Used to select the fan speed in four steps:

AUTO LOW MED HIGH

FAN Button

Active/Disable Self Clean function

SLEEP Button

FRESH Button(For RG52A3/BG(C)EFmodels only )

NOTE: While the unit is running under SLEEP

mode, it would be cancelled if MODE, FAN

SPEED or ON/OFF button is pressed.

Active/Disable sleep function. It can maintain

the most comfortable temperature and save

energy. This function is available on COOL,

HEAT or AUTO mode only .

Pushing this button to activate the FRESH

function. Pushing it again to disable.

TURBO Button

Active/Disable Turbo function. Turbo function

enables the unit to reach the preset temperature

in the shortest time. When press this button

on cooling mode, the unit will blow strong

cooling air with super high fan speed. When

press this button on heating mode(applicable

to the unit adopts PTC only), the PTC will be

energized and bring fast heating operation.

LED Button

Disable/Active indoor screen Display. When

pushing the button, the indoor screen display

is cleared, press it again to light the display.

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

SLEEP FRESH

LED FOLLOW ME

TURBO SELF CLEAN

RG52A3/BG(C)EF

RG52A2/BG(C)EF

5566

SHORTCUT Button

TIMER ON Button

TIMER OFF Button

Used to restore the current settings or resume

previous settings.

On the first time connecting to the power, if

push the SHORTCUT button, the unit will

operate on AUTO mode, 26 C, and fan speed

is Auto.

Push this button when remote controller is on,

the system will automatically revert back to the

previous settings including operating mode,

setting temperature, fan speed level and sleep

feature(if activated). And transmit the signals

to the unit.

If push this button when remote controller is off,

the system will only resume the previous

settings and will not transmit the signals to the

unit. And the sleep feature is disable.

If pushing more than 2 seconds, the system

will automatically restore the current operation

settings including operating mode, setting

temperature, fan speed level and sleep

feature(if activated ).

UP Button( )

Push this button to decrease the indoor

temperature setting in 1 C increments to 17 C.

DOWN Button( )

Press this button to initiate the auto-on time

sequence. Each press will increase the auto-

timed setting in 30 minutes increments. When

the setting time displays 10.0, each press will

increase the auto-timed setting 60 minutes

increments. To cancel the auto-timed program,

simply adjust the auto-on time to 0.0.

Press this button to initiate the auto-off time

sequence. Each press will increase the auto-

timed setting in 30 minutes increments. When

the setting time displays 10.0, each press will

increase the auto-timed setting 60 minutes

increments. To cancel the auto-timed program,

simply adjust the auto-off time to 0.0

Push this button to increase the indoor

temperature setting in 1 C increments to 30 C.

FOLLOW ME Button:

Push this button to initiate the Follow Me

feature, the remote display is actual tempera-

ture at its location. The remote control will

send this signal to the air conditioner every 3

minutes interval until press the Follow Me

button again. The air conditioner will cancel

the Follow Me feature automatically if it does

not receive the signal during any 7 minute

interval.

Swing Button

Used to stop or start horizontal louver move-

ment or set the desired up/down air flow

direction. The louver changes 6 degree in angle

for each press. If keep pushing more than 2

seconds, the louver will swing up and down

automatically.

Used to stop or start vertical louver movement

and set the desired left/right air flow direction.

The vertical louver changes 6 degree in angle

for each press. And the temperature display

area of indoor unit displays for one

second. If keep pushing more than 2 seconds,

the vertical louver swing feature is activated.

And the display area of indoor unit displays

, flashes four times, then the tempera-

IIII

ture setting reverts back. If the vertical louver

swing feature is stopped, it displays LC and

remains on for 3 seconds.

Buttons design might be slightly different

from the actual one you purchased depending

on individual models.

All the functions described are accomplished

by the indoor unit. If the indoor unit has no

this feature, there is no corresponding

operation happened when press the relative

button on the remote controller.

NOTE:

ON/OFF

MODE

FAN

TEMP

SHORT

CUT SHORT

CUT

TIMER ON

TIMER OFF

SLEEP FRESH

LED FOLLOW ME

TURBO SELF CLEAN

7788

Indicators on LCD

Transmission Indicator

Temp./Timer display

Fan speed display

Sleep Display

Mode display

ON/OFF display

This transmission indicator lights when remote

controller transmits signals to the indoor unit.

Displays the current operation mode. Including

auto( ), cool( ), dry( ), heat( ) (be

applicable to cooling & heating models only ),

fan( ) and back to auto( ).

Displays the temperature setting(17C ~30C ). When

you set the operating mode to FAN, no temperature

setting is displayed. And if in the TIMER mode, shows

the ON and OFF settings of the TIMER.

Displayed by pressing the ON/OFF button.

Press the ON/OFF button again to remove.

Displays the selected fan speed, AUTO(no display)

and three fan speed levels " " (LOW) " "

(MED) " " (HIGH) can be indicated.

The fan speed is AUTO when the operating mode is

either AUTO or DRY.

Displayed under sleeping operation.

Press the SLEEP button again to remove.

Note:

All indicators shown in the figure are for the purpose

of clear presentation. But during the actual operation

only the relative functional signs are shown on the

display window.

FOLLOW ME Display(on some models)

Displayed when FOLLOW ME function is activated.

TIMER ON display

TIMER OFF display

Displayed when TIMER ON time is set.

Displayed when TIMER OFF time is set.

How to use the buttons

Cooling /Heating/Fan operation

Ensure the unit is plugged in and power is

available.

1. Press the MODE button to select COOL,

HEAT(cooling & heating models only) or

FAN mode.

2. Press the UP/DOWN buttons to set the

desired temperature.

3. Press the FAN button to select the fan speed

in four steps- Auto, Low, Med,or High.

4. Press the ON/OFF button to start the air

conditioner.

The temperature can

OOO

be set within a range of 17 C~ 30 C in 1 C

increments.

In the FAN mode, the setting temperature is not

displayed in the remote controller and you are not

able to control the room temperature either. In this

case, only step 1, 3 and 4 may be performed.

NOTE

Auto operation

Ensure the unit is plugged in and power is

available. The OPERATION indicator on the

display panel of the indoor unit starts flashing.

1. Press the MODE button to select Auto.

2. Press the UP/DOWN button to set the

desired temperature. The temperature can

OOO

be set within a range of 17 C~ 30 C in 1 C

increments.

3. Press the ON/OFFbutton to start the air

conditioner.

1. In the Auto mode, the air conditioner can logically

choose the mode of Cooling, Fan, and Heating

by sensing the difference between the actual

ambient room temperature and the setting

temperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed.

It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , the

desired mode can be selected manually.

NOTE

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

LED FOLLOW ME

TURBO SELF CLEAN

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

SLEEP

LED FOLLOW ME

TURBO SELF CLEAN

SLEEP

991010

Dehumidifying operation

Ensure the unit is plugged in and power is

available. The OPERATION indicator on the

display panel of the indoor unit starts flashing.

1. Press the MODE button to select DRY mode.

2. Press the UP/DOWN buttons to set the

desired temperature.

3. Press the ON/OFF button to start the air

conditioner.

The temperature

can be set within a range of 17 C~ 30 C

in 1 C increments.

In the Dehumidifying mode, you can not switch the

fan speed. It has already been automatically controlled.

NOTE

Adjusting air flow direction

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

SLEEP

LED FOLLOW ME

TURBO SELF CLEAN

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

SLEEP

LED FOLLOW ME

TURBO SELF CLEAN

Timer operation

Press the TIMER ON button can set the auto-on

time of the unit. Press the TIMER OFF button

can set the auto-off time of the unit.

1. Press the TIMER ON button. The remote

controller shows TIMER ON, the last Auto-on

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired

Auto-on time. Each time you press the button,

the time increases by half an hour between 0

and 10 hours and by one hour between 10 and

24 hours.

3. After setting the TIMER ON ,there will be a one

second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "h" will disappear and the set temperature

will re-appear on the LCD display window.

To set the Auto-on time.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote

controller shows TIMER OFF, the last Auto-off

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-off time to stop the operation.

2. Push the TIMER OFF button again to set

desired Auto-off time. Each time you press the

button, the time increases by half an hour

between 0 and 10 hours and by one hour

between 10 and 24 hours.

3. After setting the TIMER OFF ,there will be a

one second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "H " will disappear and the set temperature

will re-appear on the LCD display window.

Use the SWING and SWING buttons to adjust

the desired airflow direction.

1. When push the SWING button, the horizontal

louver changes 6 degree in angle for each push.

If pushing more than 2 seconds, the louver

will automatically swing up and down.

2. When push the SWING button, the vertical

louver changes 6 degree in angle for each push.

If pushing more than 2 seconds, the louver

will automatically swing left and right.

NOTE: When the horizontal/vertical louver swing

or move to a position which would affect

the cooling or heating effect of the air

conditioner, it would automatically change

the swing/moving direction.

1111 1212

When you select the timer operation, the remote controller automatically

transmits the timer signal to the indoor unit for the specified time. Therefore,

keep the remote controller in a location where it can transmit the signal to

the indoor unit properly.

The effective operation time set by the remote controller for the timer function

is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,

5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,

21, 22, 23 and 24.

CAUTION

Example of timer setting

Start

Off

6 hours later

(Auto-on Operation)

The TIMER ON feature is useful when you want

the unit to turn on automatically before you return

home. The air conditioner will automatically start

operating at the set time.

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the last setting

of starting operation time and the signal "H"

will show on the display area.

2. Press the TIMER ON button to display "6.0H "

on the TIMER ON display of the remote

controller.

3. Wait for 3 seconds and the digital display

area will show the temperature again. The

"TIMER ON" indicator remains on and this

function is activated.

TIMER ON

Example:

Set

Stop

Set 10 hours later

(Auto-off Operation)

The TIMER OFF feature is useful when you want the

unit to turn off automatically after you go to bed. The

air conditioner will stop automatically at the set time.

To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last setting of

stopping operation time and the signal "H" will

show on the display area.

2. Press the TIMER OFF button to display "10H " on

the TIMER OFF display of the remote controller.

3. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

OFF" indicator remains on and this function is

activated.

TIMER OFF

Example:

Stop

2 hours later

after setting

Set

To stop the air conditioner 2 hours after setting and

start it again 10 hours after setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to display

2.0H on the TIMER OFF display.

3. Press the TIMER ON button.

4. Press the TIMER ON button again to display 10H

on the TIMER ON display .

5. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

ON OFF" indicator remains on and this function is

activated.

TIMER OFF TIMER ON

(On Stop Start operation)

This feature is useful when you want to stop the air

conditioner after you go to bed, and start it again in

the morning when you wake up or when you return

home.

Example:

COMBINED TIMER

(Setting both ON and OFF timers simultaneously)

Start

10 hours later

after setting

1313

Example:

TIMER ON TIMER OFF

(Off Start Stop operation)

This feature is useful when you want to start

the air conditioner before you wake up and

stop it after you leave the house.

To start the air conditioner 2 hours after setting,

and stop it 5 hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to display

2.0H on the TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to display

5.0H on the TIMER OFF display .

5. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

ON OFF" indicator remains on and this function

is activated.

Off Stop

Start

2 hours later

after setting

5 hours later

after setting

Set

NOTE: The timer setting(TIMER ON or TIMER

OFF) that in sequence occurs directly after the

set time will be activated first.

SLEEP function

The sleep function enables the unit to automa-

tically increase(cooling) or decrease(heating)

1 C per hour for the first two hours, then hold

steady for the next 5 hours, after that the unit

will stop operation. It can maintain the most

comfortable temperature and save energy.

NOTE: The SLEEP function is only available

under Cooling, Heating and AUTO operations.

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER ON

TIMER OFF

SLEEP

LED FOLLOW ME

TURBO SELF CLEAN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Direct Air Fernbedienung Handbücher

Direct Air

Direct Air RG57A3/BGEF Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung