Directechs DB3 Bedienungsanleitung
Designed by Installers for Installers
INSTALLATION GUIDE
DB3
2008 Chrysler Aspen. 403.CHRYSLER 7.34
© 2022 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Installation 6
Wiring diagram with T-Harness CHTHD2 (R1-R7 & R9-R10) or THCHD2 (R1) 6
Wiring diagram 7
Locating components in the vehicle 8
Vehicle connections 9
Module programming 11
Key-type Vehicles 11
Push-to-Start (PTS) Vehicles 12
Connecting the module 13
LED diagnostics and troubleshooting 14
Soft reset 16
Hard reset 16
Feature programming 17
Feature and option list 18
Limited one year consumer warranty 19
Quick reference guide 20
Contents
3403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
DB3 is an all-in-one door lock and override module.
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.
4403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
* Fuel Level
Immobilizer Bypass-Data No Key Req'd
RAP Shut Down (Retained ACC Power)
Remote Start Ready
Remote Start Takeover
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status
5403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible CHTHD2/THCHD2 Keys required for
programming 1Keys required for
operation 0
The optional Plug & Play CHTHD2/THCHD2 T-Harnesses are sold separately. See "Wiring diagram with T-Harness" for more
information on connections and installation instructions.
The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.
All T-Harness wires NOT listed in the diagram are NOT required for the installation.
All connectors are displayed from the wire side (unless specified otherwise).
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] When using a THCHD2 (R11) T-Harness and the security light remains ON after performing remote start takeover or the
radio turns ON when performing functions like lock and unlock, CUT and tape the T-04 loop.
[3] When using a CHTHD2 (R1- R6 & R9 - R10) & THCHD2 (R1) T-Harness and the security light remains ON after performing
remote start takeover or the radio turns ON when performing functions like lock and unlock, then CUT the Violet/Green pin
8 and Violet/Brown, pin 9 of the Red 12-pin harness.
6403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
D2D Port
Wiring diagram with T-Harness CHTHD2 (R1-R6 & R9-R10) or THCHD2 (R1 & R11)
HS CAN High: Orange/Green
HS CAN Low: Orange/Brown
16
8
9
1
CAN C Low: Pin 14
CAN C High: Pin 6
(+)12V Input (-) Drivers Door Trigger
(-) RAP Off Output: Yellow/Black
Diagnostic
Connector OBDII
(connector side view)
1412
10 42
(+) Ignition Input/ Output (+) Ignition Input/Output: Pink
(-) Ground
(-) Hood Switch (-) Hood Switch
Refer to the
“Vehicle connections” section
for wire and connector details.
(+) 12V Input
(+) Parking Light Output
(MUX)
Parking Lights:
Pink/Red,
pin 1
4
987
32
106
15
Headlight Switch
(black 10-pin conn.)
CUT
1130 Ω
Resistor
86 85
30
87a
87
Do not
connect
The Remote Start Safety
Override Switch is inactive
(used for RSR only)
XKD2D65
Sentry Key Module
(black 8-pin conn.)
To vehicle
male 8-pin connector
at the ignition switch
To 8-pin Female Connector
at the ignition switch
CHTHD2 (R1-R6 & R9-R10) or THCHD2 (R1-R11)
(optional T-Harness)
7403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
D2D Port
1412
10 42
Wiring diagram
XKD2D65
(+) Parking Light Output
(-) Ground
(-) Hood Switch (-) Hood Switch
HS CAN 1 High: Tan/Black: 3
HS CAN 1 Low: Tan : 4
(AC) Tach Input (AC) Tach Output: Violet/White: 5
(MUX) Ignition Output: Violet/Brown: 9
(MUX) Ignition Output: Violet/Green: 8
(+) Ignition Input/ Output
(+) 12V Input
(MUX)
Parking Lights:
Pink/Red,
pin 1
4
987
32
106
15
Headlight Switch
(black 10-pin conn.)
CUT
1130 Ω
Resistor
86 85
30
87a
87
CAN B High: Pin 6
CAN B Low: Pin 7
(+) Ignition: Pink/White
or Pink/Gray, pin 3
(MUX) Ignition:
Violet/Brown,
pin 1
Sentry Key Module
(black 8-pin conn.,
connector side view)
1 8
Refer to the
“Vehicle connections” section
for wire and connector details.
16
8
9
1
CAN C Low: Pin 14
CAN C High: Pin 6
(-) RAP Off Output: Yellow/Black: 10
HS CAN 2 High: Orange/Green: 5
HS CAN 2 Low: Orange/Brown: 6
Diagnostic
Connector OBDII
(connector side view)
9403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2008 Chrysler Aspen. Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN 1 High Sentry Key Module on ignition switch, black 8 pin plug, pin 6 data white/orange (CAN B BUS)
H1/4 Tan (DATA) HS CAN 1 Low Sentry Key Module on ignition switch, black 8 pin plug, pin 7 data white (CAN B BUS)
H1/5 Orange/Green (DATA) HS CAN 2 High OBD-data link connector, black 16 pin plug, pin 6 data white/pink (Diagnostic CAN C)
H1/6 Orange/Brown (DATA) HS CAN 2 Low OBD-data link connector, black 16 pin plug, pin 14 data pink/red (Diagnostic CAN C)
H1/7 Brown Relay N.O. No Connection No Connection
H1/8 Yellow Relay COM Ignition Output No Connection
H1/9 Orange/Yellow Relay N.C. Ignition Output No Connection
H1/10 Orange/Red Relay N.C. No Connection No Connection
H1/11 Yellow/Red Relay COM No Connection No Connection
H1/12 Brown/Red Relay N.O. No Connection No Connection
H1/13 Red (+) W2W Only - 12 Volt driver kick fuse box, black 40 pin plug, pin 1 + red/gray (40A)
H1/14 Black (-) W2W Only - Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter
H2/2 Green/Black No Connection No Connection
H2/3 Green/White (-) W2W Only - Door Output Remote Starter
H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter
H2/5 Violet/White (AC) W2W Only - Tach Output [1] Remote Starter
H2/6 Gray (+) W2W Only - Brake Output Remote Starter
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green (MUX) Ignition Output Sentry Key Module on ignition switch, black 8 pin plug, pin 1 MUX violet/brown
H2/9 Violet/Brown (MUX) Ignition Output Sentry Key Module on ignition switch, black 8 pin plug, pin 1 MUX violet/brown
H2/10 Yellow/Black (-) RAP Off Output Driver Door Module, brown 20 pin plug, pin 5 - violet
H2/11 Orange/Black No Connection No Connection
H2/12 Blue/Red (-) W2W Only - Hood Switch Input Remote Starter
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
10 403.CHRYSLER 7.34 2008 Chrysler Aspen
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green (-) W2W Only - Lock Input Remote Starter
H3/2 Blue (-) W2W Only - Unlock Input Remote Starter
H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter
H3/4 White/Violet (-) W2W Only - Aux1 Input Remote Starter
H3/5 Violet/Black (-) W2W Only - Aux2 Input Remote Starter
H3/6 White/Black No Connection No Connection
H3/7 Pink/White (+) W2W Only - Pk Light Input
H3/8 Violet (+) W2W Only - Starter Input Remote Starter
H3/9 Pink (+) W2W Only - Ignition Input Remote Starter
H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Blue (Data) TX
H4/2 Black (-) Ground
H4/3 Green (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A No Connection
H5/2 N/A No Connection
Additional remote start connections
(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)
Wire Connects To
Wire Location (+/-) Wire Color
12 Volts driver kick fuse box, black 40 pin plug, pin 1 + red/gray (40A)
Ground (chassis ground)
Hood Pin hood pin switch, black 2 pin plug, pin 1 - violet/lt. blue
Ignition Sentry Key Module on ignition switch, black 8 pin plug, pin 3 + pink/gray
Parking Lights MUX - Must use a resistor - Must use a relay Not Applicable
Tachometer any fuel injector ac NOT red
Andere Handbücher für DB3
18
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Directechs Automobilelektronik Handbücher
