Dish Network DISH 500 Bedienungsanleitung

Dish Antennas - Orbital Location by Dish 2 - 1

Orbital Location by Dish

Choose the correct dish antenna based on orbital locations needed.

*See options under Single Orbital Location Dishes on the next page.

DBS FSS

61.5º 72.7º 77º 110º 119º 129º 148º 105º 118.7º 121º

SingleOrbital* XXXXXXX

DISH 500 X X

DISH 1000 X X X

DISH 1000.2 X X X

DISH 500+ X X X

DISH 1000+ X X X X

1000.4 Dish X X X

SuperDISH 105 X X X

SuperDISH 121 X X X

DISH 500H X X

Dish Antennas - Single Orbital Location Dishes 2 - 2

Single Orbital Location Dishes

•Can view one DBS orbital location.*

•Use one Single or Dual LNBF.

•Use with DISH Pro/DP Plus LNBFs or switches, or Legacy LNBFs or switches.

•Do not mix Legacy and DP/DPP LNBFs and switches.

•DISH 500 with I-bracket (part number 100467); other dish antennas may be used as required.

*DBS orbital locations: 61.5°, 72.7°, 77°, 110°, 119°, 129°, 148°.

DISH 500

•Can view 110° and 119° with Y-bracket. Use two Singles or Duals, or one Twin or Quad.

•Use with DISH Pro/DP Plus LNBFs or switches, or Legacy LNBFs or switches.

•Do not mix Legacy and DP/DPP LNBFs and switches.

•Antenna dimensions: 21"W x 22.5"H.

Dish Antennas - DISH 500H 2 - 3

DISH 500H

•Larger dish antenna designed for use in Hawaii.

•Can view 110° and 119°. Uses special Y-bracket designed for use with DISH 500H.

•Use two DP Low-Noise Dual (or Single) LNBFs.

•Use with DISH Pro 34 Switch or DISH Pro Plus 33 Switch.

•Antenna dimensions: 31.5”W x 34.2”H

For more information: DISH 500H Installation Instructions.

Dish Antennas - DISH 1000 2 - 4

DISH 1000

•Views 110°, 119°, and 129°.

– Standard configuration: DP Plus Twin and DP Single/Dual.

– Can use three Singles/Duals (on a W-Bracket) and a switch.

•Use with DISH Pro/DP Plus LNBFs or switches, or Legacy LNBFs or switches.

– Do not mix Legacy and DP/DPP LNBFs and switches.

– The DP Plus 1000.2 LNBF cannot be used on a DISH 1000.

•Do not use a DP Plus 33 Switch, DP34 Switch, or DP21 Switch with the DP

Plus Twin LNBF.

•After peaking on 119°, confirm signal strength on 110° and 129°.

•The following Legacy receivers do not have 129° software support: Models 1000, 3000, 4000, 5000, JVC-DVHS (IRR),

and DishPlayer 7100/7200.

•The foot on the DISH 1000 is the same as the DISH 500, but the mast of the DISH 1000 is longer to allow for full

azimuth rotation.

•Antenna dimensions: 23.5"W x 18.5"H.

Dish Antennas - DISH 1000.2 2 - 5

DISH 1000.2

Standard Configuration

•Views 110°, 119°, and 129°.

•Standard Configuration: DP Plus 1000.2 LNBF with three receiver outputs.

•A fourth orbital location can be added using the DPP 1000.2’s LNB INport. The

LNB INport is disabled when the LNBF is connected to a switch.

•The default output of the receiver ports is 119° on PORT 1, 110° on PORT 2, and

129° on PORT 3. Note that the output ports do not follow the feed horns; PORT 1

is used for peaking on 119°.

•Any Legacy receivers must be installed with at least one DISH Pro or DP Plus

receiver to provide power to the LNBF.

With DP Plus 1000.2 LNBF

DP Plus 1000.2 LNBF

Dish Antennas - DISH 1000.2 2 - 6

DISH 1000.2 (continued)

Three-LNBF Bracket

•The Three-LNBF Bracket uses three Singles/Duals and a switch.

The W-Bracket from the DISH 1000 is not interchangeable with the

Three-LNBF Bracket.

•You cannot use a Twin/Quad LNBF with the Three-LNBF Bracket.

•Do not mix Legacy and DP/DPP LNBFs and switches.

Additional Installation Considerations

•Additional skew holes are provided on the skew plate for increased stability at

extreme skew angles (greater than 110 or less than 70).

•After peaking on 119°, confirm signal strength on 110° and 129°.

•The following Legacy receivers do not have 129° software support: Models 1000, 3000, 4000, 5000, JVC-DVHS (IRR),

and DishPlayer 7100/7200.

•Mast uses a heavier gauge steel and is slightly longer than DISH 1000, but has the same outside diameter. Only the

DISH 1000.2 mast/foot assembly should be used with the DISH 1000.2 reflector.

•Antenna dimensions: 25.9"W x 20.7"H.

Three-LNBF Bracket

Dish Antennas - DISH 1000.4 2 - 7

DISH 1000.4

•Views 61.5°, 72.7°, and 77°.

•Uses DP Plus 1000.4 LNBF with three receiver output ports.

•A fourth orbital location can be added using the DPP EA LNBF’s LNB INport.

The LNB INport is disabled when the LNBF is connected to a switch.

•The default output of the receiver ports is 77° on Port 1, 72.7° on Port 2, and

61.5° on Port 3. Peak the dish antenna on 72.7°, connecting the peaking

meter to Port 2.

•Run two Check Switch tests for the receivers to properly recognize the DP

Plus LNBF. One is run when the receiver is initially connected; the second

Check Switch test is run after the initial software download.

•LNBF and Bracket include a “keying” feature to help ensure only 1000.4 parts are

used together.

1000.4 Dish Antenna

77°

72.7°

61.5°

77° 72.7°

61.5°

1000.4 LNBF

Dish Antennas - DISH 1000.4 2 - 8

DISH 1000.4 (continued)

Installation Considerations

•All receivers must have MPEG-4 support (ViP-series receivers).

•Provides additional peaking controls for easier installation and peaking.

– Azimuth Cam provides fine-tuning of the azimuth angle.

– Elevation Rod provides fine-tuning of the elevation angle and additional installation stability.

•Nuts and bolts on the dish should be tightened using a torque wrench in a specific order. Follow the manufacturer’s

instructions for the correct order.

•When tightening the azimuth bolts, do not tighten the Azimuth Cam.

•After peaking on 72.7°, confirm signal on 61.5° and 77°.

•The 1000.4 dish antenna uses the same mast and foot as the DISH 500+.

•Mast clamp includes a gripping feature that provides additional installation stability.

•LNBF Arm has a specific installation orientation, indicated by labeling “Top” and “To LNBF”.

•Antenna dimensions: 27.8”W x 22.3”H.

1000.4 Dish - Assembly, Pointing, and Peaking 2-8a

1000.4 Dish

Antenna Assembly

2-8b1000.4 Dish - Assembly, Pointing, and Peaking

Assembly Instructions

1. Find Azimuth/Elevation/Skew angles for your location.

2. Find a location for the dish antenna with a clear line of sight and a sturdy mounting surface.

3. Mount the mast, making sure it is absolutely vertical. Attach struts to the mast, using the strut instructions.

4. Assemble the dish antenna, setting the skew and elevation angles in the process.

5. Mount the dish antenna on the mast and point the dish to the azimuth angle.

6. Run cables between the dish antenna and the receiver(s), leaving a service loop around the dish mounting bracket

and attaching cables to the mast using zip ties.

Point and Peak Instructions

Rough Point and Peak

1. Using a peaking meter attached to the DPP 1000.4

LNBF PORT 2, rough peak the dish on 72.7°W using

transponder 13, 19, or 21 for maximum strength.

Lock the mast clamp bolts and re-conrm signal.

Andere Handbücher für DISH 500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dish Network Antenne Handbücher

Dish Network

Dish Network Tailgater Bedienungsanleitung

Dish Network

Dish Network Playmaker Bedienungsanleitung

Dish Network

Dish Network DishPro Bedienungsanleitung

Dish Network

Dish Network DISH 1000.2 Bedienungsanleitung

Dish Network

Dish Network Over-the-Air Antenna Bedienungsanleitung

Dish Network

Dish Network D1000.4 EA Bedienungsanleitung

Dish Network

Dish Network SuperDISH Bedienungsanleitung

Dish Network

Dish Network DISH 1000 Bedienungsanleitung

Dish Network

Dish Network Tailgater Bedienungsanleitung

Dish Network

Dish Network DISH 500 Bedienungsanleitung

Dish Network

Dish Network DishPro Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung