Dish Network 3.1 Bedienungsanleitung

REGULATORY FACTORS

WIRELESS REMOTE CONTROL

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Changes or modifications to this device may void your authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the use is encouraged to try to correct

the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

SAFETY INSTRUCTIONS

You must keep safety in mind while using this device. Keep these

and any other instructions for future reference.

INSTALLATION

Observe Warnings: Carefully follow all warnings on the device

and in the operating instructions.

Heat: DO NOT place the device near heat sources such as radiators, stoves, heat

registers, or other appliances that produce heat.

CARE AND USE

Cleaning: DO NOT use liquid, abrasive, solvent, or aerosol cleaners. Use a damp cloth

for cleaning.

When Not in Use: Remove the batteries if this device is to be

left unattended or unused for a long period of time.

Refer servicing to qualified personnel when a solid object

or liquid has fallen onto or into the device.

DO NOT attempt to service this device. Refer all

servicing to qualified personnel. Opening covers other

than the battery cover will void the warranty.

inside_front_cover_dishnondvr.fm Page 0 Friday, November 4, 2005 2:12 PM

TABLE OF CONTENTS

Remote Control Basics....................................... 2

Models Supported by this Guide ......................... 2

UHF and IR Signals ............................................ 3

Installing Batteries............................................... 3

Converting the 4.0 Remote Control ................... 4

Setting Up to Control the Satellite Receiver ..... 5

Checking the Remote Address .......................... 7

Setting Up to Control Other Devices ................. 8

Combination Devices .......................................... 8

Limited Mode....................................................... 8

Setting Up Using Device Code Tables ................ 8

Setting Up Using Device Codes Scan................. 9

Checking the Device Codes.............................. 10

Switching Between TV and Device

Volume Control...................................................11

Remote Control Operation ............................... 12

Operating Modes............................................... 12

Controlling the Satellite Receiver ...................... 13

Controlling a TV (or a Second TV).................... 19

Controlling a VCR

(Second VCR or a DVD Player) ........................ 21

Controlling a Tuner or Amplifier......................... 23

Device Codes .................................................... 25

TV Codes .......................................................... 25

VCR Codes ....................................................... 29

TV/VCR Combo Codes ..................................... 31

DVD Player Codes............................................ 31

Tuner/Amplifier Codes....................................... 32

DVD/VCR Combo Codes .................................. 33

TV/DVD Combo Codes ..................................... 33

Troubleshooting ............................................... 34

Limited Warranty ............................................... 36

If You Need Help ................................................ 39

text_dishnondvr.fm Page 1 Monday, November 7, 2005 12:03 PM

REMOTE CONTROL BASICS

This remote control gives you easy access to all the features of a DISH

Network satellite TV receiver. You can set up the remote to control the

satellite TV receiver and up to three other devices. These devices can

be a TV, a VCR or DVD player, and a third device.

MODELS SUPPORTED BY THIS GUIDE

This user’s guide supports the following remote control models as

shown on the label on the back of the remote:

•3.0/3.1/3.2 - Infrared (IR) only. For use with appropriate

IR-controlled DISH Network receivers.

•4.0 - Infrared/Ultra-High Frequency Pro (IR/UHF Pro). For use

with appropriate UHF Pro-controlled DISH Network receivers.

The 4.0 remote can be converted to one of three different remote

types used on a DISH 322 receiver:

With the blue 2 UHF Pro key installed, this remote

will operate the UHF Pro side of the DISH 322

receiver. The remote comes with this key already

installed.

With the green 1 key installed (no UHF Pro

marking), this remote will operate the IR side

of the DISH 322 receiver. This remote will look

and work exactly like a 3.0 IR remote. See

instructions in Converting the 4.0 Remote.

With the green 1 UHF Pro key installed, this

remote will operate the side of the DISH 322

receiver from a distance using UHF Pro. See

instructions in Converting the 4.0 Remote.

If you set up your DISH 322 to operate the side

using UHF Pro, the two UHF Pro remotes for this

receiver will interfere with each other when operated at

the same time. This may prevent the remotes from

operating the receiver momentarily.

text_dishnondvr.fm Page 2 Monday, November 7, 2005 12:03 PM

INSTALLING BATTERIES

The remote control requires AAA batteries. When

you replace old batteries, you should replace all of the

batteries. Use batteries of the same kind, for example,

alkaline or carbon zinc, and don’t mix batteries of

different kinds. Alkaline batteries last longer.

1. Press down on the battery cover and slide the

cover off.

2. If you are replacing batteries, take out all of

the old batteries.

3. Put the new batteries in. Make sure

you match the plus (“+”) ends with the

plus markings on the battery case.

4. Slide the cover back into place.

UHF AND IR SIGNALS

The remote control may use either UHF radio signals or IR light

signals to control the receiver but uses only IR signals to control other

devices.

•IR signals travel only short distances (up to 40 feet),

and cannot go through walls or other solid objects.

You must point the remote control right at the device

you want to control, with no objects to block the signal path.

•UHF signals travel long distances (up to 200 feet) and can

go through walls and other solid objects. Because UHF signals

travel so far, the receiver may respond to signals from other

nearby remote controls. To handle this problem, you may want to

change the remote and receiver addresses. See Setting Up to

Control the Satellite Receiver on page 5.

•Confirm that the UHF remote antenna is attached to the receiver’s

back panel UHF REMOTE ANTENNA input so you can use

your UHF Pro remote.

text_dishnondvr.fm Page 3 Monday, November 7, 2005 12:03 PM

CONVERTING THE 4.0 REMOTE CONTROL

By replacing the key at the bottom of the 4.0 remote, this remote can be

converted to look and work like a 3.0 IR or to operate like a second

UHF Pro remote to control the side of the DISH 322 receiver. The

instructions below show you how to replace this key. After replacing

the key, follow the instructions in Setting Up to Control the Satellite

Receiver.

Note: If you do not need to replace the key, you do not need to

complete the instructions below. Go to Setting Up to Control the

Satellite Receiver.

1. Slide the battery cover off.

2. Insert your thumbnail in the

seam between the remote

control and the blue key to

separate the key.

3. Grasp the key at the bottom and pull down firmly to remove.

4. If you are converting the remote

to look and work like a 3.0 IR

remote, then turn the removed

key over with the green 1 side

up (this key should not have a

UHF Pro marking). Reinstall

the key with the green side

showing. Make sure the key

snaps in place.

Note: Key

has no UHF

Pro marking.

text_dishnondvr.fm Page 4 Monday, November 7, 2005 12:03 PM

SETTING UPTO CONTROL THE SATELLITE

RECEIVER

The remote and the receiver must be set up on the same address

so that the remote can control the receiver. When you get the remote,

it's already set up to control the receiver on address 1. However, your

receiver may be set to a different address or, in the case of the

DISH 322, may need some additional setup. To set up the remote

and receiver to work together on the same address, use the following

instructions.

5. If you are converting the remote

to operate like a second UHF

Pro remote to control the

side of the DISH 322 receiver,

then get the green 1 UHF Pro

key provided separately. Install

this key in the remote with the

UHF Pro marking showing.

If you set up your DISH 322 to operate the

side using UHF Pro, the two UHF Pro remotes

for this receiver will interfere with each other

when operated at the same time. This may

prevent the remotes from operating the receiver

momentarily.

6. If you have not already installed batteries, install them now.

See Installing Batteries for further details.

7. Slide the battery cover back into place.

Note: Key has the

UHF Pro marking.

text_dishnondvr.fm Page 5 Monday, November 7, 2005 12:03 PM

1. For DISH 322 receivers only: If you are using a 4.0 Remote

control with the green 1 UHF Pro key installed, perform the

steps a. through e. below. If not, then go to step 2.

a. Open the TV1 UHF Pro Setup screen by pressing

MENU-6-1-8 on the remote control.

b. Select Enable from the TV1 UHF Pro Setup screen.

c. Press the SYS INFO button to open the System

Information screen.

d. Move the highlight to the address for the Primary Remote

Address as shown below. This is important - if you do not

do this, your remote will change the receiver's Secondary

Remote Address and cause your Remote Control 1 to

control the side of your receiver.

Do not do this step if you are using 4.0

Remote with blue 2 key. This will cause your

Remote Control 2 to control side of your

receiver.

e. Go to step 3 below.

2. Open the System Information screen. Consult your receiver

user's guide for instructions on how to open this screen without

using the remote control. The System Information screen

will show either one Remote Address, or it may show a

Primary Remote Address and a Secondary Remote

Address.

Note: On the DISH 322, leave Done highlighted.

3. Press and hold the SAT mode button about three

seconds, until all the mode buttons light up,

and then let go of the SAT button. The SAT mode

button will blink.

4. Use the number buttons to enter any number

from 1 to 16. The SAT mode button goes out after you enter

each digit, and then lights up again.

Write down the number you entered:

Note: Highlight

the Primary

Remote

Address if you

are using a 4.0

remote with a

green 1 UHF Pro

key.

text_dishnondvr.fm Page 6 Monday, November 7, 2005 12:03 PM

5. Press the POUND (#) button.

If you entered the address correctly, the SAT mode

button will flash three times.

6. Press the RECORD button. If you are using the 4.0

remote with the green 1 key (no UHF Pro marking),

point the remote control at the receiver when you

press the RECORD button.

7. Make sure the System Information screen shows the correct

remote address as follows:

•If only one Remote Address is shown, make sure this

address matches the number you entered in step 4.

•If you are using 4.0 remote with the green 1 UHF Pro key,

make sure that the Primary Remote Address shows

UHF Pro and IR and that this address matches the number

you entered in step 4.

•If you are using 4.0 remote with the green 1 key (with no

UHF Pro marking), make sure that the Primary Remote

Address shows IR and that this address matches the

number you entered in step 4.

•If you are using 4.0 remote with the blue 2 UHF Pro key,

make sure that the Secondary Remote Address matches

the number you entered in step 4.

8. Close the System Information screen. On most receivers,

this is done by selecting the Done button. See your receiver

user's guide for more information.

CHECKING THE REMOTE ADDRESS

To read out the remote control address setting:

1. Press and hold the SAT mode button for three seconds

until all mode buttons light. Then, let go.

2. Press the POUND (#) button twice while watching

the SAT mode button.

3. Count the number of times the SAT mode button

flashes. This number is the remote address. For

example, if the SAT mode button flashes 6 times, this

indicates the remote address is set to 6.

text_dishnondvr.fm Page 7 Monday, November 7, 2005 12:03 PM

SETTING UPTO CONTROL OTHER DEVICES

To use the remote to control other devices (such as a TV, VCR, DVD

player, tuner, or amplifier), you must first program it to control these

other devices. You can do this by either following the instructions in

Setting Up Using Device Code Tables on page 8, or the Setting Up

Using Device Codes Scan procedure described on page 9.

COMBINATION DEVICES

If you are programming the remote to control a combination device,

such as a TV/VCR or a VCR/DVD, program the remote control in one

mode, and then repeat the procedure in the other mode. For example, to

program the remote to control a TV/VCR using code 748, follow the

instructions to program the remote to control the TV using code 748,

and then repeat the instructions for the VCR using the same code.

LIMITED MODE

You can program your remote control in limited mode to keep from

accidentally changing the channel on your TV or VCR. When you use

the remote to control your TV in limited mode, you will only be able to

use the POWER, MUTE, and VOLUME buttons. Also, when you use

the remote to control your VCR in limited mode, you will only be able

to use the power and VCR function buttons. The section Setting Up

Using Device Codes Tables has a step that tells the remote control to go

into limited mode.

Note: Limited mode is not used with audio amplifiers.

SETTING UPUSING DEVICE CODE TABLES

You can set up the remote to control other devices using the device

codes listed on page 25.

1. Use the device’s buttons or its remote control to turn on the

device.

2. Find the brand name of the device in the tables starting on

page 25.

If the brand isn’t listed, see Setting Up Using Device Codes

Scan on page 9.

3. Press and hold the mode button for the device you want

the remote to control, for about three seconds. When all the

other mode buttons light up, let go of the mode button - that

mode button should now be flashing.

text_dishnondvr.fm Page 8 Monday, November 7, 2005 12:03 PM

For example, hold the TV mode button for a TV until all of the

other mode buttons light. When you let go, the TV mode light

will flash.

4. Only for the AUX mode, Use a number button to enter 0 for a

second TV, or 1for a second VCR or DVD player, or 2for a

tuner or amplifier.

5. Use the number buttons to enter one of the

device codes from the table.

6. Only for limited mode, Press 1.

Note: If you want to use all of the remote

control’s features in TV mode, reprogram the

remote control following these instructions

but skip step 6.

7. Press the POUND (#) button. If you entered

the code correctly, the mode button flashes three times.

8. Press the blank POWER button to test if the

code works for the device. If it does, the

device should turn off.

9. Turn the device back on and try some other buttons to make

sure they work. Sometimes, the blank POWER button works

when other buttons don’t. If the code works for other buttons,

stop here.

10.If the code you entered doesn’t work, do steps 3 through 9 again

with another device code from the tables.

11.If you cannot find a code that works, try Scan for Device Codes

below.

SETTING UPUSING DEVICE CODE SCAN

If the code for your device is not listed in the tables on starting page 25,

use this procedure to scan the remote control’s memory for the device

code.

1. Use the device’s buttons or its remote control to turn the device

on.

2. Press and hold the mode button for the device you want the

remote to control, for about three seconds. When all the other

mode buttons light up, let go of the mode button - that mode

button should now be flashing.

For example, hold the TV mode button for a TV until all of the

other mode buttons light. When you let go, the TV mode light

will flash.

text_dishnondvr.fm Page 9 Monday, November 7, 2005 12:03 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dish Network Fernbedienung Handbücher

Dish Network

Dish Network 311k Bedienungsanleitung

Dish Network

Dish Network Platinum Plus 121150 Bedienungsanleitung

Dish Network

Dish Network 20.0 Bedienungsanleitung

Dish Network

Dish Network 301 IR 123271 Bedienungsanleitung

Dish Network

Dish Network 135331 Bedienungsanleitung

Dish Network

Dish Network Solo 301 Gebrauchsanweisung

Dish Network

Dish Network ViP 922 Slingloded DVR Bedienungsanleitung

Dish Network

Dish Network Platinum Remote Control Bedienungsanleitung

Dish Network

Dish Network 54.0 Bedienungsanleitung

Dish Network

Dish Network 54.0 Bedienungsanleitung

Dish Network

Dish Network DISHPlayer 500 Bedienungsanleitung

Dish Network

Dish Network Remote Control Bedienungsanleitung

Dish Network

Dish Network 40.0 Bedienungsanleitung

Dish Network

Dish Network ViP 211 Series Bedienungsanleitung

Dish Network

Dish Network DISHPlayer 500 7100/200 Bedienungsanleitung

Dish Network

Dish Network 176842 Bedienungsanleitung

Dish Network

Dish Network 11 Technisches Datenblatt

Dish Network

Dish Network Platinum PVR Remote Control Bedienungsanleitung

Dish Network

Dish Network EZ Bedienungsanleitung

Dish Network

Dish Network Digital PVR Bedienungsanleitung

Dish Network

Dish Network 54.0 Bedienungsanleitung

Dish Network

Dish Network 40.0 Bedienungsanleitung

Dish Network

Dish Network Platinum 121716 Bedienungsanleitung

Dish Network

Dish Network digital remote control Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung