DITEC DAB905ESE Bedienungsanleitung

www.ditecentrematic.com

Ditec DAB905ESE

Extension unit

–

12345

+24 V DC

KILL

KEY

O/C

OIMP

GND

BATTERIE

12 345678910111213

OPEN

EXIT

OFF

UNL

KRST

Serratura elettrica /

Incontro elettrico

Apertura lato esterno

Comando apre/chiude

Apertura a chiave

Chiusura di emergenza

Reset chiusura di emergenza

Porta sbloccata

Temporizzatore porta chiusa

BATTERIES

Closed door timer

Emergency closure reset

Key opening

Door released

Emergency closure

Open/close impulse

Outer side opening

Electric lock / Electric

strike

DAB905ESE

Contents

Legenda

This symbol indicates instructions or notes regarding safety, to which special attention must be paid.

This symbol indicates useful information for the correct functioning of the product.

Subject Page

1. Extension unit DAB905ESE 3

1.1 Commands 3

1.2 Outputs and accessories 5

1.3 Standard installation 5

1.4 Advanced settings available on the control panel version indicated, or subsequent versions 6

2. Example of an application with optional extension units 7

DAB905ESE

DAB905ESA

DAB905ESE

Torx T10

Long pin used for 2 Extension Unit

Short pin use d for 1 Extension Unit only

5 mm nut driver

1. Extension unit DAB905ESE

There is a command extension card for managing the electric lock / electric strike, function selector, batteries, key selector

switch and night-time closure.

1.1 Commands

Contact Function - Accessory Description

3 4

GND-OIMP

NO OUTER SIDE OPENING Contact for connection of external detection radar.

The closure of the contact activates an opening operation.

NB: this command is only active with the COM400MKB-MHB function selector switch.

3 5

GND-O/C

NO OPEN/ CLOSE IMPULSE The closure of the contact activates an opening operation. The door stays open until a new

command is given.

If the door does not receive any command, it closes automatically after 15 minutes of inactivity.

Automatic closing cannot be adjusted using the HOT trimmer; it is factory-set.

The automatic closing time can be modiﬁed from 15 min to endless (∞), setting the pre-

conﬁgured parameter 2 as explained in chapter 14.

With the ON/OFF/HOLD OPEN switch, the O/C command is always active except in the HOLD

OPEN Position.

With the program selector COM400MHB/MKB the O/C command usually functions in BI-

DIRECTIONAL mode.

If necessary, set the pre-conﬁgured parameter 8 as explained in chapter 14, the O/C com-

mand will function in BIDIRECTIONAL / MONO-DIRECTIONAL / DOOR CLOSE mode.

3 6

GND-KEY

NO KEY OPENING The closure of the contact activates an opening operation.

This command is always active, even when the COM400MHB/MKB function selector switch

or ON-OFF-HOLD OPEN switch is installed.

The automatic closure time is set to 5 s when the door is open regardless of HOT trimmer

adjustment.

Can be used for opening from night/CLOSED mode.

612345

67 8910

12345

12 345678910111213

Fix the label to the terminal board, taking care to apply it in the correct

direction (see the ﬁgure above).

–

12345

+24 V DC

KILL

KEY

O/C

OIMP

GND

BATTERIE

12 345678910111213

OPEN

EXIT

OFF

UNL

KRST

Serratura elettrica /

Incontro elettrico

Apertura lato esterno

Comando apre/chiude

Apertura a chiave

Chiusura di emergenza

Reset chiusura di emergenza

Porta sbloccata

Temporizzatore porta chiusa

BATTERIES

Closed door timer

Emergency closure reset

Key opening

Door released

Emergency closure

Open/close impulse

Outer side opening

Electric lock / Electric strike

DAB905ESE

Contact Function - Accessory Description

3 7

GND-KILL

NO EMERGENCY CLOSURE

(FIRE BARRIERS)

The closure of the contact activates an emergency closure operation. This command is ac-

tive in every situation, and has priority over every other command.

When the contact has reopened (with JUMPER J=ON), the door resumes operating as set

by the selector.

WARNING: if an EMERGENCY CLOSURE is activated, all the safety functions are

ignored and the door closes. People or objects in the path of the door during the

closing operation could suffer serious injury or damage.

This function is generally used to cut off a speciﬁc area in the case of a ﬁre.

NB: this command can be combined with an emergency button.

The output contact can be changed from NO to NC by altering the pre-conﬁgured param-

eters, as explained in chapter 13.

The operation of the block during the emergency closure can be selected from the pre-set

parameters explained in chapter 13.

A panic bar can be installed in combination with a magnetic block on the ﬁre barrier.

In the event of a ﬁre alarm or a power supply failure, the panic bar keeps the closed door

blocked. In the case of escape routes, the panic bar can be manually released.

Conﬁgure the relay contact of the DAB905ESA card, choosing parameter 11, 12 or 13 as

explained in chapter 13.

3 7

GND-KILL

NO “NURSE & BED” FUNC-

TION

Available on the control panle version indicated, or subsequent versions.

In installations with parallel doors, the “NURSE & BED” function can be enabled by con-

necting a switch to contacts 3-7 on the SLAVE door control panel.

1801123456

6DAB205CU

SOLUTION 1

Connect a bridge between 3 and 7 on the slave DAB905ESE.

Use any impulse on master to open master door.

Use O/C impulse on Slave to open both doors.

SLAVE MASTER

IIMP

(MASTER)

OIMP

(MASTER)

MASTER

SLAVE

FOR BED

FUNCTION

ONLY

FOR BED

FUNCTION

ONLY

12345

+24 V DC

KEY

O/C

OIMP

GND

12 345678910111213

OPEN

EXIT

OFF

UNL

KRST

KILL

DAB905ESE

SLAVE

SOLUTION 2

Connect a bridge between 3 and 7 on the Slave DAB905ESE.

Set dip switch PAG on Master board to ON.

Use any impulse on master to open master door.

Push slave door manually and it will open up automatically and stay open until master door

is closing.

SOLUTION 3

Connect a bridge between 3 and 7 on Slave DAB905ESE.

Set dip switch PAG on Slave board to On.

Any impulse on the master control unit:

- Shorter than 2 s opens only master door.

- Longer than 2 s opens both doors.

Note: How to connect KILL input is determined by chosen parameter group at the slave, be

sure that chosen group has KILL impulse conﬁguration Normally Open. If KILL has to be

Normally Closed, terminal 3 and 7 should be disconnected instead of connected.

DAB905ESE

Output Description

+24V DC

GND

3 ... 13 Output for the power supply to the accessories 24V 400 mA max.

NB: the maximum absorption of 400 mA corresponds to the sum of all the accessories installed.

Output for connecting an electric lock / electric strike.

Select the type of power supply using the DIP1 and the type of electric lock / electric strike using the DIP2

With DIP2 in OFF ( electric lock / electric strike Normal), and no COM400MHB/MKB function selector switch (or the latter

in BIDIRECTIONAL mode), output 1-2 is permanently powered = door closed not locked. ( referring status 1 chapter 17.4).

If, on the other hand, you want to lock the door wing with the door closed, set the selector to BIDIRECTIONAL mode or make

a jumper GND-EXIT (3-11). In this condition, output 1-2 is powered throughout the operation from opening until complete

closure; for this reason, locks with mechanical reset cannot be used.

With DIP2 in ON ( electric lock / electric strike Anti-panic), the behaviour will be the same except for the fact that output 1-2

will always be unpowered in BIDIRECTIONAL mode and throughout the open/close operation in MONODIRECTIONAL mode”.

For different setting see Chapter 17.4 Management of electric lock / electric strike power supply.

OPEN

EXIT

OFF

GND

3 ... 10 11 12 Output for connecting the function selector switch.

If the function selector switch is on OFF, the Push and Go function is disabled.

If a function selector switch is installed, disconnect the ON/OFF/HOLD switch (if present).

BATTERY BATTERY KIT

If no mains power supply is available, the battery kit will guarantee operation in "energy-saving" mode.

If no mains power supply is available, the door only operates with the key switch connected to 3 GND -6 KEY.

In “energy-saving” mode, the door can remain stationary for up to a week while waiting for the KEY command.

The following sensors are not active during “energy saving” operation:

-OPD motion sensor

-PIMP reversal safety contact

-PDET opening safety device

In this mode (on automations connected in parallel), connect the batteries only to the MASTER automation ﬁtted with

DAB905ESE.

By changing the pre-conﬁgured parameter group, you can set the battery kit to CONTINUITY mode. If no mains power

supply is available, the door operates normally until the batteries are fully discharged.

In this mode, on automations connected in parallel, connect the batteries on both automations equipped with DAB905ESE.

NB: for charging purposes, the battery kit must be connected to the control panel at all times.

A new kit with fully-charged batteries can usually open and close a door consecutively in CONTINUITY mode.

If you want to check the battery kit is working correctly, set DIP5=ON.

In the event of a battery alarm, the DAB105CU control panel LED will ﬂash twice.

Monitoring of batteries must always be reset when batteries are replaced. To RESET press and hold the LRN

button while battery mode is active (with mains power supply disconnected).

An acoustic/light alarm signal can be connected to terminals 6-7-8 on the DAB905ESA card.

1.3. Adjustments

1.2 Outputs and accessories

Trimmer

Trimmer Description

Adjustment of the opening delay time, from 0 s to 3 s.

With DIP3=ON, the door release is active throughout the opening delay.

Dip-switches

DIP Description OFF ON

DIP1 Power supply to the electric lock / electric

strike.

12 V max 500 mA 24 V max 250 mA

DIP2 Type of electric lock / electric strike.

DO NOT USE ELECTRIC LOCKS / ELEC-

TRIC STRIKES WITH A RESET FEATURE.

Normal

When it is powered, the door

can be opened.

Anti-panic

When it is unpowered, the door can be opened.

DIP3 Electric lock / Electic strike function Disabled Prior to the opening, a closure thrust is made simultaneous-

ly with the electric lock / electric strike activation impulse.

DIP4 Electric lock / electric strike coupling Disabled Enabled

When it approaches the closing stop, the door increases its

force/speed to ensure correct closure on the electric lock /

electric strike.

DIP5 Battery test Disabled Enabled

Jumper

Description OFF ON

JEmergency closure reset (FIRE BARRIERS ONLY) Manual Automatic

For more information, refer to the COM400MKB-MHB selector manual.

DAB905ESE

1.4 Advanced settings available on the control panel version indicated, or subse-

quent versions

Increased thrust force on closure when an electric lock is ﬁtted

Management of electric lock / electric strike power supply

1. Disconnect batteries if any.

2. Disconnect the mains.

3. Press the LEARN BUTTON (LRN) and keep it depressed.

4. Connect the mains.

5. Watch the ERROR LED.

3s1s3s1s3s1s3s1s3s

6. Release the LEARN BUTTON after 5 ﬂashes (LED is out).

7. Identify the current lock kick status:

The ERROR LED ﬂashes an amount of short ﬂashes that correspond to the status number.

After a short pause the LED will repeat the status number and so on.

8. Changing the status:

If you push the LEARN BUTTON once, the status number will increase.

When you have reached the highest status number it will start at number one again.

• Push the button until you get the requested lock kick status, 1=Basic (default), 2=Enhanced

• Disconnect the mains

Next time the mains is connected, the operator will use the new status setting.

1. Disconnect batteries if any.

2. Disconnect the mains.

3. Press the LEARN BUTTON (LRN) and keep it depressed.

4. Connect the mains.

5. Watch the ERROR LED.

3s1s3s1s3s1s3s1s3s 3s1s

6. Release the LEARN BUTTON after 6 ﬂashes (LED is out).

7. Identify the current lock unlocked status:

The ERROR LED ﬂashes an amount of short ﬂashes that correspond to the status number.

After a short pause the LED will repeat the status number and so on.

8. Changing the status:

If you push the LEARN BUTTON once, the status number will increase.

When you have reached the highest status number it will start at number one again.

• Push the button until you get the requested status.

1= With DIP2 in OFF and no COM400 function selector switch ( or the latter in two-way mode), output 1-2 is permanently powered (default) ; for this

reason, locks with mechanical reset cannot be used.

2= With DIP2 in OFF and no COM400 function selector switch ( or the latter in two-way mode), when the operator received an open command, output

1-2 is powered through the ﬁrst 10° of door opening and through the last 10° of closing; for this reason, locks with mechanical reset cannot be used.

With the selector on BIDIRECTIONAL mode or with a jumper GND-EXIT (3-11), the output 1-2 is powered only through the ﬁrst 10° of door opening;

for this reason, locks with mechanical reset can be used.

• Disconnect the mains.

Next time the mains is connected, the operator will use the new status setting.

01123

DAB105CU

DAB905ESE

2. Example of an application with optional extension units

PASS24 (OIMP - DAB905ESE)

PASS24 (IIMP)

COM400MHB (DAB905ESE)

Locking Device (DAB905ESE)

Open/close (DAB905ESE)

Closing timer (DAB905ESE)

Emergency

closing Reset (DAB905ESE)

Emergency

closing (DAB905ESE)

DAB105

DAB205

DAB305

REM

(DAB905ESA)

Battery

(DAB905ESE) Error indication or door open (DAB905ESA)

Error indication or door open (DAB905ESA)

Emergency closure reset

(DAB905ESE)

Emergency closure (DAB905ESE)

Battery

(DAB905ESE)

Electric lock/ Electric Strike

(DAB905ESE)

Open/close (DAB905ESE)

Closing timer (DAB905ESE)

Entrematic Group AB

Lodjursgatan 10

SE-261 44, Landskrona

Sweden

www.entrematic.com

DAB905ESE

All the rights concerning this material are the exclusive property of Entrematic Group AB.

Although the contents of this publication have been drawn up with the greatest care, Entrematic Group AB cannot be held responsible in any way

for any damage caused by mistakes or omissions. We reserve the right to make changes without prior notice.

Copying, scanning or changing in any way is expressly forbidden unless authorised in writing by Entrematic Group AB.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung