Ditek DTK-TSS5 Bedienungsanleitung

DTK-TSS5

Total Surge Solution

User Guide

DITEK CORPORATION

One DITEK Center

1720 Starkey Road

Largo, Fl 33771

DTK-110RJC6APOE (10 Gigabit Ethernet Surge Protector)

Application

Surge suppression for PoE circuits transmitting video and/or data over CAT6

or CAT6A cable.The DITEK is wired in series and terminates with a 110 punch

down to RJ45 Plug.

DITEK CORPORATION

One DITEK Center 1720 Starkey Road Largo, Fl 33771

1-800-753-2345 www.ditekcorp.com

Sales: 1-800-753-2345

Technical Support: 1-888-472-6100

191593 INT-100162-001 Rev 1

DISCONNECT CIRCUIT BEFORE BEGINNING INSTALL.

1. Connect the incoming (field) wires to the IDC (110) punch down block using the

proper punch down tool designed for IDC connectors. Using any other tool will

damage the IDC connector and void warranty.

2. Follow the wire color codes printed on the circuit board next to the IDC

connectors for wire termination points.

T568A Wiring- BL-BL/W, BR-BR/W, OR/W-OR, GR-GR/W

T568B Wiring- BL-BL/W, BR-BR/W, GR/W-GR, OR-OR/W

This connector is rated for 26-22AWG solid conductor wire.The wire pairs must be

twisted together and maintain that twist all the way to the punch down block.

3. If using STP (Shielded Twisted Pair) the shield must be connected to the

“Shield GND” termination screw located on the circuit board near the IDC connector.

This can be accomplished by twisting the shield into a wire and wrapping it under

the screw.

4. Using the velcro loops provided, secure the CAT6/CAT6A cabling to the circuit

board.

5. Using a CAT6 or CAT6A rated patch cord with a properly tipped RJ45 connector,

plug one end into the DITEK and the other end into the equipment to be protected.

6. After all connections have been made and no hazards exist, restore the circuit.

GR / W

OR/W

BR / W

BL / W

DTK-110RJC6APOE

TO PROTECTED EQUIPMENT

3’ MINIMUM LENGTH

Note: T568B Wiring Shown

INPUTOUPUT

INCOMING (FIELD) WIRING

GROUND WIRE 14 AWG

MINIMUM

SHIELD GND

DITEK TSS5

(Total Surge Solution)

System Overview

TSS5 (Total Surge Solution)

The TSS5 is an integrated surge protection solution for control panels. This device

provides transient voltage surge protection for two channels of PoE circuits and

protection for the 120VAC source of supply.

Installation

Cabinet

Caution: This installation should be performed by a licensed electrician.

Note: Install this device between the field wiring and the alarm panel.

Disconnect system power and loop circuits before beginning installation.

1. Locate an appropriate area for the cabinet near the alarm panel to be protected.

2. Position the TSS cabinet on the finished wall surface and fasten the cabinet

to the wall.

3. Remove the appropriate knockouts from the cabinet to facilitate the routing of

the field wiring and alarm panel supply wiring . Make sure the field wiring and

the protected wiring to the alarm panel occupy separate conduit feeds.

4. Pull the field wiring and the alarm panel supply wiring through the appropriate

knockouts on the cabinet. Make sure to route the AC power wires separately

from the loop circuit wires.

DTK-120SRD (120V Series Surge Protector)

Warning !! Turn power off at the main circuit breaker panel.

Note: Connect this device in series between the AC power supply wiring and the

alarm panel AC inputs.

1. Crimp the supplied ring terminals to the connection wires.

2. Connect the Ground (green or bare) supply wire to the ground buss on the

back plane. The GROUND on the DTK-120SRD has been factory pre-wired. It is not

necessary to make any additional ground connections.

3. Connect the Neutral (white) supply wire to the NEUTRAL terminal on the Input side.

4. Connect the Phase (black) supply wire to the LINE terminal on the Input side.

5. Connect the Ground, Neutral and Phase wires from the Output side to the alarm

panel AC inputs.

6. After all connections have been made and metal nuts have been torqued to 10

inch pounds, install the plastic protective cover and fasten with the included nylon

nuts until snug, then restore power.

11"

12"

12”

NO C NC

DRY CONTACT

120VAC(+)

NEUTRAL(

)

LOAD: 120VAC, 0.5AMP (MAX)

EXAMPLE MONITORING CIRCUIT

EXAMPLE REMOTE MONITORING

USING FACP FOR NOTIFICATION

DTK-120SRD

DRY CONTACT CIRCUIT INFORMATION

DITEK CORPORATION

One DITEK Center 1720 Starkey Road Largo, Fl 33771

1-800-753-2345 www.ditekcorp.com

191593 INT-100162-001 Rev 1

GROUNDED

120 VAC POWER TO

ALARM PANEL.

(Installer Provided)

GROUND WIRE TO

GROUND BUSS

(Chassis Ground)

(Factory Pre-Wired)

GROUNDED

120 VAC POWER

(Installer Provided)

Ground Buss

DTK-5MB Ground

(Factory Pre-Wired)

Ground For Future Use On

Additional Bases (Installer Provided)

SURGE PROTECTIVE DEVICE

DTK-120SRD

CAUTION !!!

HIGH VOLTAGE

MADE IN USA

WWW.DITEKCORP.COM

NC C NO

Dieses Handbuch passt für folgende Modelle

Andere Ditek Überspannungsschutz Handbücher

Ditek

Ditek D200-4803D Konfigurationshandbuch

Ditek

Ditek DTK-240X12 Bedienungsanleitung

Ditek

Ditek DTK-RM16POC Konfigurationshandbuch

Ditek

Ditek DTK-TSS2 Bedienungsanleitung

Ditek

Ditek D50-277/4803Y Konfigurationshandbuch

Ditek

Ditek D200-347/6003Y Konfigurationshandbuch

Ditek

Ditek D200-120/2401 Konfigurationshandbuch

Ditek

Ditek DR Series Bedienungsanleitung

Ditek

Ditek DTK-RM12POE Konfigurationshandbuch

Ditek

Ditek DTK-DF240S12 Bedienungsanleitung

Ditek

Ditek DTK-WM4 Series Konfigurationshandbuch

Ditek

Ditek DTK-SNAP-LITE Series Bedienungsanleitung

Ditek

Ditek D200-277/4803Y Konfigurationshandbuch

Ditek

Ditek DTK-120/240CM+ Konfigurationshandbuch

Ditek

Ditek DTK-TSS4D Konfigurationshandbuch

Ditek

Ditek DTK-DP4P Bedienungsanleitung

Ditek

Ditek D50-2403D Konfigurationshandbuch

Ditek

Ditek ZEUS Series Bedienungsanleitung

Ditek

Ditek DTK-DF120S1 Bedienungsanleitung

Ditek

Ditek DTK-RM12POE Konfigurationshandbuch

Ditek

Ditek DEFLECTOR Series Bedienungsanleitung

Ditek

Ditek DTK-RM12NETS Konfigurationshandbuch

Ditek

Ditek DTK-110C6A Konfigurationshandbuch

Ditek

Ditek DR Series Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung