Ditel SXT48S Bedienungsanleitung
SXT48S
QUICK INSTALLATION GUIDE
AUTO-TUNE PID
TEMPERATURE CONTROLLER
WITH CONTROL RELAY / SSR
GENERAL SPECIFICATION
Installation and use of this device must be done by qualified, authorized and trained technical personnel only.
Inspect device carefully before installation. Do not install and use broken and defective devices.
Do not disassemble device. Do not make any repair on any part of the device. There is no accessible part inside the
device. Please contact to manufacturer for broken and defective devices.
Do not use device in environments subject to flammable, explosive and corrosive gases and/or substances.
This device is designed for applications only in light industrial environments. This device is not suitable for medical
and residential use. This device is not suitable for use related with human health and safety. This device is not suita-
ble for automotive, military and marine use.
Do not allow children and unauthorized people to use this device.
Before installation and any technical work, disconnect the power supply and mains connections.
Check the power supply voltage level before power on, and make sure voltage level is in specified limits.
Check quality of neutral line. Improper neutral line may give permanent damage to the device.
Connect an external power switch and an external fuse (1A, 250VAC) to the power supply line that are easily acces-
sible for rapid intervention. Connect an external fuse (2A, 250VAC) for each relay output separately.
Use appropriate cables for power supply and mains connections. Apply safety regulations during installation.
Install the device in a well ventilated place. Install the device permanently into a proper panel cut-out. Fix the device
with two fasteners supplied with the device. Only front panel must be accessible after installation is completed.
Do not operate the device other then the environmental conditions given in Technical Specification.
WARNINGS
DOWNLOAD
USER MANUAL
WIRING
WARNING: if 2 wire Pt100 is used, connect compensation lead to
measuring lead: (SXT48S: 10-11)
Use correct compensation cables for T/C sensors.
Connect T/C cable directly to the device connectors.
Keep device, signal cables and communication cables away from circuit breakers, power
cables and devices/cables emitting electrical noise.
Use shielded and twisted signal and communication cables and connect shield to earth
ground on device side.
Keep length of signal and communication cables less than 3m.
Use insulated cable end-sleeves at the end of cables screwed to the device connector
terminals.
TECHNICAL SPECIFICATIONS
· Dimensions : 48x48mm
· Panel Cut-out : 45,5x45,5mm
· Display : 4 Digits 7 Segment (PV), 4 digits 7 Segment (SV)
· Sensor Type : J,K,T,S,R type T/C, Pt100 selectable
· Measuring Scale : -100..600 ºC, J type T/C (Inpt=J), -100.0 .. 600.0 ºC, J type T/C (Inpt=J.0)
-100..1300 ºC, K type T/C (Inpt=k), -100.0..999.9 ºC, K type T/C, (Inpt=k.0)
-100..400 ºC, T type T/C (Inpt=t), -100.0 .. 400.0 ºC, T type T/C (Inpt=t.0)
0..1750 ºC, S type T/C (Inpt=S) 0 .. 1750 ºC, R type T/C (Inpt=r)
-100..600 ºC, Pt100, (Inpt=Pt) -100.0 .. 600.0 ºC, Pt100, (Inpt=Pt.0)
· Resolution : ± 1 ºC or ± 0.1 ºC
· Accuracy : ± 1 % (Over full scale)
· Control Form : ON-OFF or P, PI, PD, PID - selectable
· Control Output : Relay (NO + NC), 250VAC, 2A, Resistive load / SSR (12Vdc, 20mA) - selectable
· Heat SET : Lower Limit .. Upper Limit ºC (H.Set)
· Heat Hysteresis : 0 .. 50 / 0.0 .. 50.0 ºC (H.Hys); PID is active if set to 0
· Alarm Hysteresis : 1 .. 50 / 0.1 .. 50.0 ºC (A.Hys)
· Proportional Band : 5 .. 150 ºC (Pb.C)
· Integral Time : 0:00 .. 30:00 min:sec. (OFF if set to 0:00)
· Derivative Time : 0:00 .. 10:00 min:sec. (OFF if set to 0:00)
· Control Period : 1 .. 200 sec. (Ct)
· Offset : -100..+100 ºC / -100.0 .. +100.0 ºC (oFFS)
· Heating/Cooling : Selectable (only ON-OFF control form is active for cooling)
· Cold. Junc. Comp. : 0 .. 50 ºC (T/C)
· Line Comp. : 10 Ohm max. (3 wire Pt100)
· Sensor Failure : OUT output is active according to P.Err and Ct parameters in case of sensor
failure, measurement out of range or hardware fails to measure input signal
(OUT output is OFF if P.err is 0).
· Supply Voltage : 100..240VAC, 50-60Hz
· Power Consumption : < 8VA
· Humidity : < 70% (non-condensing)
· Altitude : < 2000 m
· EMC : EN 61000-6-1, EN 61000-6-3 (Only light industrial environment)
· Safety : EN 61010-1; Pollution degree 1, measurement category I, (Only light industrial
environment, double/reinforced isolated, non-conductive pollution environment)
· Protection Class : IP20; according to EN 60529
· Temperature Spec. : Operating: 0 .. 50 ºC, Storage -10ºC .. 60ºC (no icing)
· Weight : < 0.5 kg
· Torque for screwing : Max. 0.5 N.m
This device and its packing is NOT litter and may NOT be disposed of with domestic waste. Please return this device and its
packing to an appropriate recycling point at the end of its service life.
SXT48S
MFR’D 06 21
000000000000
PROGRAMMING PARAMETERS
DOWN UP BACK SET
(1)When sensor type is changed, Up.L, Lo.L, H.Set, H.hys, oFFs Error Messages:
may be set to a new value automatically, according to the selected sensor. Fail: Sensor failure or sensor selection wrong
(2) If sensor type is selected as Pt.0, J.0, K.0 or t.0. E.FLS: Hardware failure
E.CAL: Hardware failure
E.EPr: Memory failure
20230621 30727802
DISEÑOS Y TECNOLOGÍA, S.A.
Xarol, 6B P.I. Les Guixeres
08915 Badalona (Barcelona) - Spain
Tel. +34 933 394 758
Fax +34 934 903 145
Email: comercial@ditel.es ; web: www.ditel.es
PROGRAMMING HEAT SET
ON-OFF is active when “H.Hys” is other then 0
ON-OFF CONTROL
PID PARAMETERS
- P, PI, PD, PID is active when “H.Hys” is set to 0 (only for heating; h-C is set to ”HEAt”)
- PbC: Proportional band in ºC.
- Ct: Control period for PID control. Prefer 4-10 sec.
- Ti: Integral time; Set in minutes. Determines how fast controller reacts to compensate the offset between SET
point and the process value.
If set to 0, integral part is OFF. If set too low, process value may oscillate.
- Td: Derivative time; Set in minutes. If set to 0, derivative part is OFF. Determines how sensitive the controller is
to changes of the offset between SET point and the process value. If set too high, process value may oscilla
te or overshoot.7
CLEANING
Do not use any solvents (alcohol, thinners, benzine, acid, etc.) or corrosive substances to clean the device.
Use only a dry and clean non-abrasive cloth.
Before cleaning, disconnect the power supply and mains connections.
Inhaltsverzeichnis
Andere Ditel Temperaturregler Handbücher
Beliebte Temperaturregler Handbücher anderer Marken
Swegon
Swegon LUNAd MB Bedienungsanleitung
Lucky Reptile
Lucky Reptile Thermo Control II Bedienungsanleitung
SENSORMETRIX
SENSORMETRIX Argon 100 Bedienungsanleitung
Fuji Electric
Fuji Electric PXE4 Bedienungsanleitung
Yuyao gongyi
Yuyao gongyi XMT-808 series Bedienungsanleitung
Selec
Selec TC544C Bedienungsanleitung
