Divus KNX SERVER Bedienungsanleitung

INSTALLATION GUIDE

INSTALLATIONSANLEITUNG

Version 1.3

REV02-20150608

INDEX

1 GENERAL INFORMATION - 3 -

1.1 Conventions - 3 -

1.2 Safety Instructions - 4 -

1.3 Standard - 5 -

2 FIRST COMMISSIONING - 6 -

2.1 Introduction - 6 -

2.2 Content of the Packaging - 6 -

2.3 Installation, Connection and Commissioning - 6 -

2.3.1 Installation and Connection - 6 -

2.3.2 Environmental Conditions - 7 -

2.3.3 Commissioning - 7 -

2.4 Maintenance / Warranty - 8 -

2.5 Network connection - 8 -

2.6 Reset of the IP address - 9 -

3 IN THREE STEPS TO A VISUALISATION - 10 -

DIVUS GmbH

Pillhof 51

I-39057 Eppan (BZ)

Operating instructions, manuals and software

are protected by copyright. All rights are re-

served. Copying, multiplication, translation and

conversion, either partially or as a whole, is not

permitted. You are allowed to make a single

copy for back-up purposes.

We reserve the right to make changes to the

manual without prior notication.

We assume no responsibility for any errors or

omissions that may appear in this document.

We do not assume liability for the awlessness

and correctness of the programs and data

contained on the delivered discs.

You are always welcome to inform us of er-

rors or make suggestions for improving the

program.

The present agreement also applies to special

appendices to the manual.

This manual can contain terms and descrip-

tions, which inproper use by third can harm

the copyrights of the author.

Please read the manual before beginning and

keep the manual for later use.

The manual has been conceived and written

for users who are experienced in the use of

PCs and automation technology.

[KEY]

Keys that are to be pressed by the user are

given in square brackets, e.g. [CTRL] or [DEL]

Courier

On-screen messages are given in the Courier

font, e.g. C:\>

Courier bold

Keyboard input to be made by the user are gi-

ven in Courier bold, e.g. C:\>DIR).

“…” (double quotes)

Names of buttons to be pressed, menus or

other onscreen elements and product names

are given within double quotes. (e.g. “Con-

guration”).

Symbolic

In this manual the following symbolic are used

to indicate particular text blocks.

Caution! A dangerous situation may

arise that may cause damage to ma-

terial

Note. Hints and additional notes

1 GENERAL INFORMATION

1.1 CONVENTIONS

The present operating instructions contain

those safety instructions that are required to

safely operate the machine.

All persons working with the machine must

heed the present operating instructions, espe-

cially the safety instructions.

In addition, all local stipulations governing the

prevention of accidents must be heeded.

Only trained and authorized personnel may in-

stall and operate the machine.

Proper application: The machine has been de-

signed for application in building automation.

The machine has been built using state-of-

the-art technology and all applicable safety

regulations. However, damage or negative ef-

fects to the machine or other material cannot

be excluded if the machine is operated.

The machine meets the requirements of the

EMC guidelines and of the harmonized Euro-

pean standards. Modications to the machine

hardware may aect the system’s EMC com-

patibility.

Without special protection measures, the

machine must not be used in EX areas and in

plants that require special monitoring.

Danger of explosion. Do not expose the buer

batteries to heat. Serious injury may be the

result.

The operating voltage of the machine must be

within the specied range! The product label

provides the required information.

1.2 SAFETY INSTRUCTIONS

DIVUS KNX SERVER meets the following guidelines and standards:

LOW VOLTAGE DIRECTIVE 2006/95/CE

Standard to which conformity is declared:

EN 60950-1: 2001-02 Safety

EMC DIRECTIVE 2004/108/CE

Standard(s) to which conformity is declared:

Emissions:

EN 61000-6-4 :2002-10

EN 55022:1999 (+A1:2001) Conducted & Radiated Emissions

Immunity:

EN 61000-6-2 :2002-10

EN 61000-4-2: 1996 (+A1:1998,+A2:2001) Electrostatic Discharges

EN 61000-4-4: 1996 (+A1:2001,+A2:2002) Electrical Fast Transient / Burst

EN 61000-4-5: 1997 (+A1:2001) Surge

EN 61000-4-11: 1997(+A1:2001) DIPS & Voltage Variations

EN 61000-4-6: 1997(+A1:2001) Conducted RF

EN 61000-4-3: 1997(+A1:1999,+ A2:2001) RF Electromagnetic Field

EN 61000-4-3: 1997(+A1:1999,+A1:2001) 50 Hz Magnetic Field

The installation and wiring instructions contained in this documentation must be heeded. Confor-

mity is indicated by the attached CE label.

The EC conformity statements can be obtained from:

DIVUS GmbH

Pillhof 51

I-39057 Eppan (BZ)

Regarding DIRECTIVE 2002/96/EC waste electrical and electronic equipment has to be

collected separately and is not allowed to dispose as unsorted municipal waste.

1.3 STANDARD

The KNX SERVER packaging contains the fol-

lowing material:

˚DIVUS KNX SERVER

connector for power supply and KNX bus

KNXCONTROL stick, containing the develop-

ment software (PDK) and detailed documen-

tation

Printed installation guide

2.2 CONTENT OF THE PACKAGING

KNX SERVER is a pure web server

and not usable for standalone visu-

alisation, because it has no display.

The visualisation is accessed through client

PCs like e.g. touch panels of DIVUS, which

connect via network to the server. The ser-

ver has no graphical interface (VGA, DVI,

HDMI, ...) and therefore can’t display any

graphical contents.

KNX SERVER is, like most KNX components,

mounted on a DIN rail. For a correct function,

the following connections must be guaranteed:

˚Power supply 12-30V DC (current consumption

240 mA a 12V) using the supplied connector

˚KNX bus connection via supplied connector

˚Network connection via CAT5 network cable

(not supplied)

2.3 INSTALLATION, CONNECTION AND COMMISSIONING

2.3.1INSTALLATION AND CONNECTION

KNX SERVER is a web server, on which the

cross-platform software OPTIMA is running.

This way KNX SERVER becomes a web based

visualisation and monitoring solution for

home & building automation systems, which

are realized according to the world wide KNX

standard. The conguration and the use of

OPTIMA takes place directly over the OPTIMA

web interface that can be displayed on dif-

ferent devices / operating systems through

using a conventional web browser.

2 FIRST COMMISSIONING

2.1 INTRODUCTION

Details about the conguration

of OPTIMA can be found in the

OPTIMA ADMINISTRATOR-MANUAL,

while details about the usage of the vi-

sualisation can be found in the OPTIMA

USER-MANUAL.

The LED marked with the label „POWER“ on

the front of the server signals that the power

supply is active, while the “SERVICE” LED re-

mains o in normal circumstances.

KNX SERVER has furthermore the following

interfaces:

˚SD-slot: to expand the memory of KNX

SERVER with an appropriate SD-card

˚RS232-interface and 2 USB-ports: for integ-

ration of third party systems

When commissioning KNX SERVER, the fol-

lowing steps must be followed:

˚Power o the system/installation

˚Install KNX SERVER on a DIN-Rail

˚Connect power supply and KNX bus to

KNX SERVER

˚Power on the system/installation

˚Wait until KNX SERVER has booted up

The correct function of KNX SERVER can be granted only if the following requests are met:

OPERATION Ambient temperature 0°C - 50°C

STORAGE Ambient temperature -10°C - 70°C

2.3.2ENVIRONMENTAL CONDITIONS

DIVUS KNX SERVER is power supplied by a po-

wer adapter NOT included in the KNX SERVER

packaging.

The device supports power supply voltages of

12-30V DC.

2.3.3COMMISSIONING

ATTENTION!

Before commissioning KNX SERVER

all connections must be checked! Verify that

the voltage of the connected power supply

doesn’t exceed the supported voltage ran-

ge, in order to avoid damage on the device!

ATTENTION!

If the KNX SERVER hardware is

changed, irreversible damage can occur.

Any intervention on the equipment should

be performed only by authorized person-

nel of DIVUS.

The connection to the KNX bus is

not really needed for the congura-

tion of KNX SERVER, but it allows a more

ecient programming, since direct tests

of the system can be performed.

For the usage/conguration of KNX SERVER a

working network connection is required. In or-

der to make the rst access to KNX SERVER, or

if a compatible network is not available, follow

these steps:

˚Connect KNX SERVER through a crossed net-

work cable (“crossover-cable”) with your PC

˚Open the network conguration of your PC

˚Change the settings of the TCP/IP – Protocol

(Version 4) of the network interface, on which

you connected the KNX SERVER using a net-

work cable and enter the following values:

˚IP address: 192.168.0.100

˚Subnet mask: 255.255.255.0

˚Gateway: 192.168.0.110

˚Save the new settings; depending on the ins-

talled OS a restart can be necessary.

Once the network settings have been chan-

ged, open a browser on your PC (Google Chro-

me preferred) and enter the following URL into

the address bar of the browser:

2.5 NETWORK CONNECTION

DIVUS KNX SERVER is completely fanless and

has no moving parts. The industry-tested

hardware, the reduced size and minimal power

consumption make it ideal for home automa-

tion. The PC does not require any complicated

installation or maintenance and there are no

special requirements on the installation loca-

tion.

The PC has 24 months warranty from date of

delivery (date of the delivery document). This

can only be maintained if the device is shipped

back for reparation in its original packaging,

with all the shock-absorbing parts.

To be noticed:

Each repair shipment must be approved by

our technical support. Please contact us using

[email protected]. You may then get all the

necessary information, as well as the docu-

ment „repair request“.

Repair shipments must be boxed within the

original packaging. Otherwise we can’t gua-

rantee any warranty. If the device was shipped

in an improper packaging a at fee for a new

original packaging for the return shipment will

be charged to the customer. In addition, the

“repair request” document must be lled out

correctly and be shipped together with the de-

vice, in order to provide an ecient service and

a processing time of 2 weeks.

For technical reasons, only complete systems

can be accepted for reparation.

2.4 MAINTENANCE / WARRANTY

This link will directly open the login page of

OPTIMA, where you can login as administrator

with the following login credentials.

After successful login, the conguration menu

can be reached by clicking on the ADMIN-button

in the toolbar of the displayed navigation menu

( - show/hide navigation menu). Detailed in-

formation about the visualisation and congu-

ration of OPTIMA can be found in the OPTIMA

USER-MANUAL and the OPTIMA ADMINISTRA-

TOR-MANUAL.

If needed, the IP address of KNX SERVER can

be reset to factory settings through the RE-

SET-button on the bottom side of the device:

˚Localize the RESET-button on the device and

get a screw driver or a similar tool with a small

diameter to reach the RESET-button through

the small cutout in the housing of the device.

˚Press the RESET-button until the SERVICE-

LED starts blinking (about 10 seconds); after-

wards release the RESET-button.

˚Press the RESET-button again within the next

5 seconds for max. 2 seconds and then re-

lease the button again; after a short pause

the SERVICE-LED stays on for some seconds.

˚As soon as the SERVICE-LED turns o,

KNX SERVER is reachable under the factory-IP

address (“192.168.0.110”)

If the SERVICE-LED stops blinking after the

RESET-button was pressed for the rst time

(10 seconds) and before you were able to

press the RESET-button again, please repeat

the whole procedure.

2.6 RESET OF THE IP ADDRESS

http://192.168.0.110

Username: admin

Password: admin

The maximum comfort for using/

programming DIVUS OPTIMA can

be achieved with the following browsers:

• GoogleChrome

• AppleSafari

ETS PROJECT

The start point for the creation of the KNX

visualisation with DIVUS OPTIMA is your ETS

project.

Using the OPC export in ETS can be created

a project le that contains all the in-formation

needed from DIVUS OPTIMA.

ETS IMPORT

In the conguration area of DIVUS OPTIMA

under “TECHNOLOGIES - KNX – ETS IMPORT”,

you can nd a wizard, which will guide you

through the ETS-Import.

Select the project le created in step 1 and

follow the steps on the screen.

VISUALISATION

After the import and the conguration of the

KNX functions, you can start to create the

visualisation. For this you can create several

rooms in the conguration area under “VISUA-

LISATION – ROOMS”.

To equip the new created rooms with KNX ob-

jects, you can search them using the search

engine and drag&drop the whished objects into

the corresponding tables of the whished rooms.

Detailed information about the programming/

usage of DIVUS OPTIMA can be found in the

OPTIMA ADMINSTRATOR-MANUAL/OPTIMA

USER-MANUAL.

3 IN THREE STEPS TO A VISUALISATION

Inhaltsverzeichnis

Sprachen:

Andere Divus Server Handbücher

Divus

Divus OPTIMA RC3 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung