Dji Ronin-S Bedienungsanleitung

RONIN-S/SC

Phone Holder

2019.06v1.0

User Guide

使用说明

使用說明

ユーザーガイド

사용자 가이드

Bedienungsanleitung

Guía de usuario

Guide de l'utilisateur

Guida dell'utente

Gebruiksaanwijzing

Manual do utilizador

Guia do usuário

Руководство пользователя

Introduction

The Ronin-S/SC Phone Holder was designed to securely mount mobile devices using

adjustable bracket, allowing users to utilize their mobile device as an extended

monitor and operate ActiveTrack and Force Mobile more efciently.

Usage

The phone holder can be used in three ways.

Method 1

Attach the phone holder to the top of the camera’s hot shoe, then select ActiveTrack

through the Ronin app. Note that ActiveTrack is only usable through this method.

Installation

1. Detach the bottom of the phone holder by rotating the mounting knob.

2. Attach the phone holder to the top of the camera’s hot shoe, then secure the

mobile device into the phone holder’s bracket. Note that the mobile device has to

be positioned horizontally as shown below. Additionally, the mobile device should

be as close to the camera lens as possible.

3. Power on the camera and mobile device. Ensure that the frame of the camera and

mobile device are focused on the same subject. The tilt angle of the mobile device

can be adjusted by loosening the phone angle knob. After adjustment, be sure to

retighten the phone angle knob.

Balancing

1. Balancing depth for the tilt axis

a. Unlock the tilt axis and lower the camera by loosening the tilt axis knob 1.

b. Rotate the tilt axis so that the camera lens is pointing forward. Check to make

sure the camera is not front or back-heavy. If front-heavy, move the camera

backward. If back-heavy, move the camera forward.

c. Loosen the knob under the camera mounting plate 2and adjust the camera

balance 3until the camera is steady.

d. Tighten the knob.

2. Balancing the vertical tilt

a. Rotate the tilt axis so that the camera lens is tilting up for about 45 degrees. Check to

make sure the camera is not top or bottom-heavy. If the camera is tilted to one side,

pull the tilt arm towards the other side.

b. Loosen the knob on the tilt motor 1and adjust the balance of the camera 2until

the camera is steady without tilting up or down.

c. Tighten the knob.

d. Repeat Step 1 to balance the depth of the tilt axis. The slider on the dovetail plate is

used to record the balance position. Move the slider next to the mounting plate and

tighten the slider.

3. Balancing the roll axis

a. Lock the tilt axis and unlock the roll axis. Check the direction in which the roll

motor swings. If the camera rotates to the left, move the camera to the right. If

the camera rotates to the right, move the camera to the left.

b. Loosen the knob on the camera mounting plate 1, and adjust position of the

plate 2until the camera is steady.

c. Tighten the knob. If the camera moves forward, move the camera back until the

slider is next to the mounting plate.

45°C

Operate carefully to

avoid the phone collides

with the motor.

4. Balancing the pan axis

a. Unlock the pan axis. Hold the grip, tilt Ronin-SC sideward, and check the

movement of the pan axis. If the camera lens rotates downward, push the pan

axis backward. If the camera lens rotates upward, push the pan axis forward.

b. Loosen the knob on the pan motor 1. Adjust the camera balance 2until the

camera is steady when rotating the pan while lifting the grip.

c. Tighten the knob.

Be sure the gimbal is balanced every time you change the payload.

Refer to the mobile device support list to learn which phone models are

compatible with the phone holder for using ActiveTrack.

ActiveTrack can only be used when Ronin-SC is operating in Underslung

mode and Upright mode. Do not use it in Flashlight mode.

Method 2

Attach the phone holder to a handlebar, tripod or similar platform, then open Force

Mobile through the Ronin app. Here, you can adjust the gimbal attitude by rotating the

mobile device.

Installation

1. Detach the bottom of the phone holder by rotating the mounting knob.

2. Attach the top of the phone holder to the quick-release clamp of the handlebar

through the screw hole on the phone holder.

3. Attach the quick-release clamp with the phone holder to the handlebar. Secure

the mobile device into the phone holder’s bracket.

Force Mobile is only available when using an iOS device.

Method 3

Install the phone holder to the RSA port on Ronin-SC. You can adjust camera parameters

through the camera app.

Installation

1. Detach the RSA adapter plate from the phone holder, then attach the RSA adapter plate

to the RSA port and x with screws.

2. Attach the phone holder to the RSA adapter plate, then tighten the mounting knob.

3. Secure the mobile device into the phone holder’s bracket, and adjust its viewing angle

with the phone angle knob.

The phone holder can be rotated

360°, allowing the mobile device to be

positioned vertically or horizontally.

To use the mobile device as an

extended monitor, users will need

a compatible camera app, such as

Sony Imaging Edge Mobile, Panasonic

Image App, Nikon SnapBridge, Fuji

Camera Remote, and Canon Camera

Connect, and will also need to secure a

Wi-Fi connection between their mobile

device and camera.

CHS

简介

Ronin-S/SC 手机夹适配 Ronin-S/SC，可放置手机以使用智能跟随、体感控制功能，或

利用手机当监视屏或调参屏使用。

使用

方式一

安装手机夹至相机顶部热靴接口，放置手机后配合 Ronin App 使用智能跟随功能。注意

智能跟随功能只适用于此应用场景。

安装步骤

1. 旋转旋钮，拆下手机夹底部连接部分。

2. 安装相机至 Ronin-SC 后，安装手机夹至相机顶部热靴接口，拧紧后放置手机。请将

手机横向放置，并使手机摄像头与相机镜头距离最小。

3. 开启相机和手机相机，调整手机俯仰角度，确保手机拍摄与相机拍摄画面一致。拧松

手机夹侧边旋钮后可调整俯仰角度，调整完毕后拧紧旋钮。调整手机角度后再进行平

衡调节。

平衡调节

1. 俯仰轴的前后平衡调节

a. 解锁俯仰轴 1，并尽量将俯仰轴往下调。

b. 使相机镜头水平朝前，判断相机重心偏向。当相机镜头往前倾，说明重心在俯仰轴

前方，需将相机往后移动；当相机镜头往后倾，则将相机往前移动。

c. 拧松安装底座底部旋钮 2，前后调节相机位置 3。

d. 锁紧旋钮。若相机能稳定停留，表示已调节平衡。

2. 俯仰轴的垂直平衡调节

a. 翻转相机使镜头朝上约 45 度，判断相机重心偏向。当相机镜头往一侧倾斜，需将

力臂往反向移动。

b. 拧松旋钮 1后调节相机位置 2。

c. 拧紧旋钮，相机镜头朝上 45 度时能稳定停留代表已调节平衡。

d. 重复步骤 1，再次精调俯仰轴前后平衡，以达到最佳效果。俯仰轴平衡调节完成后

使记忆滑块紧贴安装底座后拧紧，以记录相机俯仰轴平衡位置。

3. 横滚轴的平衡调节

a. 锁定俯仰轴，解锁横滚轴，然后判断相机重心偏向。若相机向左侧倾斜，说明相机

重心在横滚轴左侧，需将安装底座连同相机往右移动；若相机向右侧倾斜，则将安

装底座连同相机往左移动。

b. 拧松安装底座旋钮 1，左右调节相机位置 2。

c. 拧紧旋钮。若相机能稳定停留，表示已调节平衡。若调节横滚轴过程中相机前后位

置改变，可通过记忆滑块找回俯仰轴平衡位置。

45°C

调节平衡时注意手机

不要磕碰云台。

4. 平移轴的平衡调节

a. 锁定横滚轴，解锁平移轴。握住云台向侧边倾斜，观察相机在平移轴旋转方向。若

相机镜头往下方旋转，需将平移轴力臂往后推；若相机镜头往上方旋转，则将平移

轴力臂往前拉。

b. 拧松平移轴旋钮 1，推拉平移轴力臂调整相机位置 2。

c. 拧紧旋钮，若云台平移轴在任意角度都能保持静止不动，表示已调节平衡。

完成平衡调节后可通过 Ronin App 使用智能跟随功能，请参考 Ronin-SC 用户手册了解

详情。

每次改变云台负载（包括更换相机或镜头、使用或不使用手机夹以及手机等情

况）都需要重新调节平衡。

请在 DJI 官网参考《手机支持列表》了解支持使用智能跟随功能的手机型号。

请在 Ronin-SC 工作在正立和倒立模式下使用智能跟随功能，手电筒模式下

不建议使用。

方式二

安装至手持横杆或通用三脚架等平台，使用 Ronin App 体感控制功能，通过控制手机姿

态来控制 Ronin-SC。

安装步骤

1. 旋转旋钮，拆下手机夹底部连接部分。

2. 通过手机夹底部螺纹孔和手持横杆快拆组件连接，安装手机夹至手持横杆。

仅支持 iOS 设备使用体感功能控制云台。

方式三

安装手机夹至 RSA 配件接口，放置手机充当监视屏使用，可通过手机调节相机参数。

安装步骤

拆卸底板，然后安装至 RSA 配件接口。将手机夹主体与底板连接，放置手机。

手机夹支持 360 度旋转调节方向，夹

持手机部分横向、竖向可调。

充当监视屏使用时，手机需下载相

应相机App（如索尼 Imaging Edge

Mobile，松下Image App，尼康

SnapBridge，富士 Camera Remote，

佳能Canon Camera Connect，第

三方 Field Monitor），并且连接相机

Wi-Fi 后使用。

Andere Handbücher für Ronin-S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere dji Kamerazubehör Handbücher

dji

dji RONIN 2 Bedienungsanleitung

dji

dji Zenmuse Z15-GH4 (HD) Bedienungsanleitung

dji

dji OSMO MOBILE 6 Bedienungsanleitung

dji

dji crystalsky CS785 Bedienungsanleitung

dji

dji RONIN-S Focus Motor Bedienungsanleitung

dji

dji ZENMUSE L1 Bedienungsanleitung

dji

dji RONIN 4D Bedienungsanleitung

dji

dji Zenmuse X5R Bedienungsanleitung

dji

dji OSMO Bedienungsanleitung

dji

dji OM 4 Bedienungsanleitung

dji

dji RONIN-S BG37 GRIP Bedienungsanleitung

dji

dji OSMO Bedienungsanleitung

dji

dji Zenmuse XT Bedienungsanleitung

dji

dji OSMO MOBILE 3 Bedienungsanleitung

dji

dji Ronin Bedienungsanleitung

dji

dji OSMO MOBILE 2 Bedienungsanleitung

dji

dji Three-Channel Follow Focus Bedienungsanleitung

dji

dji Phantom 2 Vision + Bedienungsanleitung

dji

dji OSMO MOBILE 3 Bedienungsanleitung

dji

dji OSMO MOBILE 2 Bedienungsanleitung

dji

dji OSMO Bedienungsanleitung

dji

dji Ronin-S Bedienungsanleitung

dji

dji OSMO MOBILE 3 Bedienungsanleitung

dji

dji RONIN-SC Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung

Custom Brackets

Custom Brackets Digital PRO-M Bedienungsanleitung

Vivo

Vivo MOUNT-LT01C Bedienungsanleitung