dji LIGHTBRIDGE Bedienungsanleitung
DJI LIGHTBRIDGE
Quick Start GuideV1.01
IN THE BOX
INTRODUCTION
Air system x1
Rectangle headed training
port cable x2
Charger x1
HDMI cable(D-D)x1
Micro-USB cable x1
Air system panel antenna x2
Ground system antenna x2
Air system antenna x3
GIMBAL cable x1（A）
DBUS cable x1
AV cable x1
Air system
Air system
antenna
Link button
Remote controller
link indicator
AV input port Aircraft control port
DJI HD input port
HD input port
Video link indicator
Firmware upgrade port
Remote controller cables x2
Ground system x1
Optional packect(1)
Optional packect(2) HDMI cable for Zenmuse x1
Ground system holder x1
Smart phone holder x1
DIY Power & CAN cable x1
LINK
VIDEO
UPGRADE
DBUS
GIMBAL PORT
AV
HDMI IN
CONTROL
Ground system
Cables
Video link
indicator
Power indicator
Power button
Ground system
antenna
If used with PHANTOM 2, connect cable to
reserved 6-PIN port on central board for air
system power supply and OSD info input.
The air system’s DBUS receiver outputs control
signals. Connect to flight control system DBUS
to receive these signals.
Connect a camera’s AV output to AV input port.
For remote controller training port connection. Connect
red port 1 to a remote controller for aircraft control and
black port 2 to a remote controller for gimbal control.
Remote controller training cable:
Connect the red jack to the aircraft remote
controller to control.
Air system antenna:
Use for connecting the Air system.
For remote controller training port and remote
controller cable connection.
Connect to Air system GIMBAL port, one end
for power, the other for CAN port.
HD video output
Remote controller port
Firmware upgrade port
HD video output port
(mobile devices / tablets)
Power adapter port
GIMBAL cable: 7PIN →6PIN(A)
DBUS cable:
AV cable:
Remote controller cable:
Training port cable:
DIY Power & CAN cable
1
2
VIDEO POWER
11V~26V USB
HDMI OUT
CONTROL IN
UPGRADE
6 pin port on Phantom 2
central board
Antennas
X2
Phantom 2 and GoPro Gimbal Connection
1. Attach air system to the bottom of Phantom 2 as shown above.
2. Install antennas diagonally on landing skids. Ensure both of the antennas
point downward.
3. Connect HDMI port on GoPro with HDMI(In) port on air system with
supplied HDMI cable.
4. Remove Phantom 2 shell, connect the X2 port on Phantom 2 with DBUS
port on air system. Re-install Phantom 2 shell.
5. Connect 6 pin port on Phantom 2 with GIMBAL port on air system with
supplied GIMBAL cable(A).
DBUS
INSTALLATION
HDMI cable
DJI HD Gimbal Connection (BMPCC)
X2
1. Fix the antennas at the
unobstructed position with
the antenna extension cable.
2. Connect DBUS port with
X2 port with supplied
DBUS cable.
3. Connect air system
GIMBAL port with DJI HD
gimbal G7 port with GIMBAL
cable(B).
4. Select either HDMI(IN) or
AV(IN) when using DJI HD
gimbal.
AV
DBUS
Compulsory Mutually Exclusive Connect when required
1. Attach the air system antenna to the unobstructed position on the aircraft via the
extension cable.
2. Connect DJI LIGHTBIRDGE DBUS port to flight controller X2 port via DBUS cable.
3. Connect GIMBAL port to the power source through DIY power cord. Attach CAN
connector to the CAN port on the flight controller (CAN1 port for A2).
4. To link the 5.8GHz transmitter, connect GCU AUX2 port to the 5.8GHz receiver.
5. Connect DJI LIGHTBRIDGE AV port with GCU video port via AV cable.
Connect DJI LIGHTBRDIGE HDMI input port wit camera HDMI output port with
HDMI cable.
Disconnect HDMI from the gimbal before powering, allow time for the gimbal to
perform self-check procedure. Failure to do so may damage the HDMI cable.
Re-connect the HDMI to the gimbal when self-check is finished.
Power
Compulsory Mutually Exclusive Connect when required
X2
DBUS
CAN
5.8G
A
B
A
B
DJI SD Gimbal Connection (GH3 for demo)
DIY Connection
X2
X2
1. AV and HDMI video input is mutually exclusive.
2. Connect air system DBUS port with X2 port on WK-M or NAZA-M.
3. Power air system with the power cords extracted from GIMBAL cable.
4. Connect GIMBAL cable to the CAN bus on NAZA-M or WK-M.
HDMI
AV
DBUS
Power
CAN
Compulsory Mutually Exclusive Connect when required
Ground system installation
Compulsory Mutually Exclusive Connect when required
HDMI and USB video
output is mutually
exclusive. USB video
output to mobile devices
is recommended.
Connect HDMI supported monitor
to HDMI OUT port in the ground
system for HDMI video viewing.
Connect the training port and the Control In port on the ground system
using the training port cable and remote controller cable.
Disable RF function of the remote control before connecting the remote
control to the ground system via the trainer port by following the
instruction below(based on Futaba remote control):
Hold the “RTN” button and power on the remote control. Enter “POWER
MODE”. Select “RF OFF” mode and press “RTN button” to confirm.
Installing antennas
Note：
Keep antennas pointing skyward
for optimum transmission. Keep
antennas away from metal. We
recommend placing ground system
on DJI remote holder.
B
C
HDMI and USB output is mutually exclusive. HDMI output overrides USB
output.
Dual remote controllers mode only available for DJI HD gimbal.Red
port connects to aircraft and black port connects to gimbal.
USB
HDMI OUT
CONTROL IN
1
2
A
A
B
C
Be aware of the antenna angle while in flight, adjust ground system
antenna angle to improve signal quality.
Illustration for installing mobile device holder and ground system holder.
(Base on DJI remote controller [side view])
Illustration for installing mobile device holder and ground system holder.
(Base on DJI remote controller [top view])
Illustration 1
Illustration 2
Illustration 3
Ground System and Remote Controller Installation
POWER ON
LINK
1. Maintain a distance of 0.5m to1m between the air and ground systems,
then power on the air system.
Use a pin to press [LINK] button on the air system. Press and hold on for 5
seconds then release. When link is finished, the [CONTROL] indicator on air
system will turn a solid green. (See the following table for indicator details)
Linking is completed when the Lightbridge is shipped. [CONTROL]
indicator light will show a solid green when powered on. If re-linking
is necessary, [CONTROL] indicator light will blink green, then follow
the above steps.
Notes:
CONTROL：
LINK：
2. Power on ground system.
Remote controller link indicator
Linking in progress.
Successful link.
Link button
Press button once to display battery capacity. Press
again and hold 2 seconds to power on / power off.
Make a note of battery capacity before
use. (Read the battery capacity description
in manual for more details)
Ground system: Power on
Indicator Description
Signal detected but not linked.
No detected signal.
Andere Handbücher für LIGHTBRIDGE
5
Inhaltsverzeichnis
Andere dji Mikrofonsystem Handbücher
Beliebte Mikrofonsystem Handbücher anderer Marken
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Bedienungsanleitung
Alpha Technologies
Alpha Technologies RBMS Bedienungsanleitung
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Bedienungsanleitung
Shure
Shure UA844 Bedienungsanleitung
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Bedienungsanleitung
Pyle
Pyle PDWM5000 Bedienungsanleitung