DLS ELETTA CAPPUCCINO EVO Bedienungsanleitung
Doc. Nr.: DSDL_20013_A
[1]
Data Sheet and Service Manual
ECAM 46.860 –ELETTA CAPPUCCINO EVO
Date: 08.09.2020
ENGLISH
TABLE OF CONTENTS:
1. TECHNICAL DATA ................................................................................................................................... 2
2. MAIN DIFFERENCES COMPARED TO ECAM45.760....................................................................... 2
3. HYDRAULIC DIAGRAM........................................................................................................................... 3
4. WIRING DIAGRAM.................................................................................................................................... 4
5. WORKING PRINCIPLE............................................................................................................................. 6
6. SELECT TEST MODE ............................................................................................................................ 10
7. APPLIANCE DIAGNOSTICS................................................................................................................. 14
Doc. Nr.: DSDL_20013_A
[2]
1. TECHNICAL DATA
Voltage 220-240V / 50-60 Hz
MAX. Input power 1450 W
COMPONENTS
Pump ULKA EP5GW 230Vac - 48W –Bar 15
Grinder motor 230Vac
Transmission motor 230Vdc with position encoder
Solenoid valves EV1, EV2 230Vac
Thermoblock
- Temperature probe NTC sensor for temperature set point
- Thermal fuse TCO 192 °C
- Heating element 230Vac –1400 W
Steamer
- Temperature probe NTC sensor for temperature set point
- Thermal fuse TCO 318 °C
- Heating element 230Vac –1100 W
2. MAIN DIFFERENCES COMPARED TO ECAM45.760
Missing main power supply switch on the back of the appliance.
Missing water softener filter from the welcome set.
Default Aroma set at level 4 for Espresso and for Espresso x2 (as per STIWA requirements).
Default grinder setting at 4.5 (as per STIWA requirements).
3 temperature levels (as per STIWA requirements).
Doc. Nr.: DSDL_20013_A
[3]
3. HYDRAULIC DIAGRAM
Doc. Nr.: DSDL_20013_A
[4]
4. WIRING DIAGRAM
Doc. Nr.: DSDL_20013_A
[5]
CAPTION:
M1: Upper Micro Switch (Transmission Group)
M2: Lower Micro Switch (Transmission Group)
M3: Drawer Micro Switch
M4: Water Tank Micro Switch
M5: IFD (Milk Jug) Presence Micro Switch
M6: Hot Water Pipe / Cleaning Micro Switch
EV1: 3-Ways Solenoid Valve
EV2: 3-Ways Solenoid Valve
L: Live/Phase
N: Neutral
TCO: Thermal Cut-Off
H.E.: Heating Element
Doc. Nr.: DSDL_20013_A
[6]
5. WORKING PRINCIPLE
5.1. MICRO SWITCHES, SENSORS AND SOLENOID VALVES
MICRO SWITCHES
Function
Logic
M1 = UPPER MICRO SWITCH
Detects when the infuser is on top
position
“NC”, it opens when the infuser is in top
position
M2 = LOWER MICRO SWITCH
Detects when the infuser is on down
position
“NO”, it closes when the infuser is in down
position
M3 = DRAWER MICRO SWITCH
Detects when the drip tray is in
correct position
3-pin micro switch. When the drip tray is
inserted:
- the contact for the drip tray
detection is OPEN;
- the contact for the transmission
motor power supply is CLOSED.
M4 = WATER TANK MICRO
SWITCH
Detects the presence of the water
tank
3-pin micro switch. When the water tank is
inserted:
- the contact for the water tank
detection is OPEN;
- the contact for the transmission
motor power supply is CLOSED.
M5 = IFD MICRO SWITCH
Detects the presence of the milk jug
“NC”, it opens when the accessory is
present
M6 = HOT WATER SPOUT /
CLEAN MICRO SWITCH
Detects the presence of the hot
water spout or starts the CLEAN
function for the milk jug
“NC”, it opens when the hot water spout is
present or when the milk jug knob is in the
CLEAN position
ENCODER
Function
Logic
HALL SENSOR ENCODER
Detects rotations of transmission
motor
SOLENOID VALVE
Function
Logic
EV1 = 3-ways solenoid valve
Allows the water flow to go to the
Thermoblock
When activated, the water flow goes to the
Thermoblock.
When deactivated, the water flow goes to
the Steamer.
EV2 = 3-ways solenoid valve
Allows the hot water and the steam
to flow to the connection nozzle
When activated, the water/steam flow
goes to the connection nozzle
Doc. Nr.: DSDL_20013_A
[7]
5.2. ESPRESSO COFFEE DELIVERY
Espresso coffee delivery stages:
- EV1 solenoid valve is activated
- Thermoblock is activated
- Grinder is activated for a certain timing (based on the coffee taste selection)
- Infuser moves to the mechanical valve
- Pump is activated for a couple of seconds for pre-infusion
- Pump restarts for coffee delivering
- Pump and thermoblock stop, EV1 closes
- Infuser moves away from the mechanical valve and releases the coffee pod
- Mechanical valve discharges excess water/coffee to the drip tray
- Infuser is moved back to the “Coffee Ready” position
Cold water
Hot water
Coffee
Discharge
Doc. Nr.: DSDL_20013_A
[8]
5.3. HOT WATER DELIVERY
Hot water delivery stages:
- EV1 and EV2 are activated
- Thermoblock is activated
- Pump is activated in fast pulsing mode for a certain timing
- Hot water is delivered through the hot water spout connected to the nozzle
- Pump stops, thermoblock, EV1 and EV2 are deactivated
Cold water
Hot water
Discharge
Doc. Nr.: DSDL_20013_A
[9]
5.4. MILK FROTH PREPARATION
Milk froth delivery stages:
- EV2 is activated
- Steamer is activated
- Pump is activated in slow pulsing mode for a certain timing
- The steam is injected from the nozzle into the milk jug and mixed with the air (according to the milk
froth knob position) to froth the milk
- EV2, steamer and pump are deactivated
Milk jug cleaning stages:
- EV1 and EV2 are activated
- Thermoblock is activated
- Pump is activated in very slow pulsing mode for a certain timing
- Hot water is delivered through the nozzle and air from the milk jug knob in CLEAN position
- EV1, EV2, thermoblock and pump are deactivated
Cold water
Steam
Discharge
Doc. Nr.: DSDL_20013_A
[10]
6. SELECT TEST MODE
With the appliance in stand-by (plug connected to the power supply socket), remove the drip tray, then hold
the below buttons pressed simultaneously:
until the message SELECT TEST MODE will appear on the display. Then, within 10 seconds, re-insert the
drip tray and select one of the following functions:
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere DLS Kaffeemaschine Handbücher
