DMX4ALL NanoDMX USB Interface Bedienungsanleitung

NanoDMX USB Interface

User Manual

NanoDMX USB Interface 2

Description

The NanoDMX USB Interface is an “adapter cable” which enables a simple control

with the PC of DMX-capable devices.

Due to the USB-Port no external power supply is necessary. Each interface is

provided with a micro-controller storing the value of all 512 channels and generating

the DMX-signal without burding the PC.

To keep down the transmission time on the DMX-line, the interface transfers only so

many what’s necessary for controlling.

For usage this NanoDMX USB Interface with the current software a virtual COM-

PORT will be applied in the system. It enables the data transfer like a conventional

serial port.

Data Sheet

Power supply: 250mA via USB

DMX-OUT: up to 512 Channels

Frame rate: up to 44 Frames/sec. by 512 DMX-Channels

PC-Connection: USB

Cable length: ca. 1m

USB-Driver: CDC-Driver (Virtual COM Port)

Windows® Version: Windows® 2000 or higher

NanoDMX USB Interface 3

Installation

The installation of the NanoDMX USB Interface is based on the Windows® internal

CDC-Driver. It is a RS232-Emulation via USB from Windows2000. When connecting

the NanoDMX USB interface, a virtual com port is set up on the PC, which can be

accessed by any Windows program as well as a real RS232 interface.

After plugging in the NanoDMX USB Interface, follow the hardware assistant and

select Specify Other Source as source for the driver and then select the location of

the driver.

Please execute the following installation steps according to the windows instructions

until the installation is completed.

The installation can differ depending on the used operation system and driver

version.

Current drivers are a

vailable as download on our hom

epage

www.dmx4all.de

Deactivate the Engine saving mode for USB:

The USB-devices are separated from Windows XP and Windows Vista in the device

manager of the system controlling if they are not addresses permanently. This can

cause problems for the USB-communication. To avoid this problems the following

set ups need to be taken:

Please deactivate the function Computer turn off device to save energy (Computer

kann Gerät ausschalten, um Energie zu sparen) under the menupoint Energy

administration.

Note: It is possible that the modifications will be passed after a restart.

Install the software from a list or

another specific source

Searching

removeable media

NanoDMX USB Interface 4

Windows-Driver Installation

Please follow the single installation steps for installation:

1. Connect the interface to a USB-Port and wait until Windows completed the

driver search.

2. Open the device manager and click with the right mouse button at the

interface. Select Driver Software Update ....

3. Select Auf dem Computer nach Treibersoftware suchen

4. Select Aus einer Liste von Gerätetreibern auf dem Computer auswählen

NanoDMX USB Interface 5

5. Alle Geräte anzeigen and click Next

6. Select Medium

7. Thus select inf-file from CD

8. Click OK

NanoDMX USB Interface 6

9. Click Next

10. Confirm the warnings with Yes and Die Treibersoftware trotzdem

installieren

11. Complete the installation with Finish

NanoDMX USB Interface 7

Information for the usage with the program FreeStyler

Please select as device in the Interface Setup DMX4ALL 3rd generation and select

the according COM-Port:

NanoDMX USB Interface 8

Settings

Use the program DMX-Configurator to configure the interface.

You find under the menu Settings →Hardware settings the possibility for adjusting as

follows:

Min Output channels adjusts the number of

generated DMX-Channels. By right clicking

the mouse the selection menu with the

number of channels opens.

Note: If you have adjust the number of

output channels to one value and if they

addresses a higher channel, so up to this

channel the DMX-Signal will be generated

automatically. This number of channels will

NOT be stored permanently.

Disable USB serial number

For all interfaces the identical USB-identifier

will be used.

Use unique USB serial number

For each interface an unique USB-identifier will be used.

Use fixed USB serial number

Always the same serial number will be used as USB-identifier.

Enable SLOW-DMX-MODE

The number of DMX-frames pro second will be reduced to ca. 33.

After confirming with OK the interface will be configured and the settings will be

stored permanently. Also after turning off the settings are restored and can be

changed only with a renewed configuration.

NanoDMX USB Interface 9

CE-Conformity

This device is controlled by a microprocessor and uses high

frequency. In order to maintain the properties of the module with

regard to CE conformity, installation into a closed metal housing in

accordance with the EMC directive 2014/30/EU is necessary.

Risk-Notes

You purchased a technical product. Conformable to the best available technology the

following risks should not excluded:

Failure risk: The device can drop out partially or completely at any time without

warning. To reduce the probability of a failure a redundant system structure is

necessary.

Initiation risk: For the installation of the board, the board must be connected and

adjusted to foreign components according to the device paperwork. This work can

only be done by qualified personnel, which read the full device paperwork and

understand it.

Operating risk: The Change or the operation under special conditions of the

installed systems/components could as well as hidden defects cause to breakdown

within the running time.

Misusage risk: Any nonstandard use could cause incalculable risks and is not

allowed.

Warning: It is not allowed to use the device in an operation, where the safety of

persons depend on this device.

Disposal

Electronical and electronic products must not be disposed in

domestic waste. Dispose the product at the end of its service life

in accordance with applicable legal regulations.

Information on this can be obtained from your local waste

disposal company.

DMX4ALL GmbH

Reiterweg 2A

D-44869 Bochum

Germany

Last changes: 04.03.2019

All rights reserve. No part of this manual may be reproduced in any form (photocopy, pressure, microfilm or in another

procedure) without written permission or processed, multiplied or spread using electronic systems.

All information contained in this manual was arranged with largest care and after best knowledge. Nevertheless errors are to be

excluded not completely. For this reason I see myself compelled to point out that I can take over neither a warranty nor the

legal responsibility or any adhesion for consequences, which decrease/go back to incorrect data. This document does not

contain assured characteristics. The guidance and the characteristics can be changed at any time and without previous

announcement.

Inhaltsverzeichnis

Andere DMX4ALL Aufnahmegeräte Handbücher

DMX4ALL

DMX4ALL ArtNet-DMX STAGE-PROFI 1.1 Bedienungsanleitung

DMX4ALL

DMX4ALL ArtNet-DMX-UNIVERSE 4.1 Bedienungsanleitung

DMX4ALL

DMX4ALL ArtNet Relais/Analog Interface 4 Bedienungsanleitung

DMX4ALL

DMX4ALL DMX UNIVERSE DR1.1 RDM Bedienungsanleitung

DMX4ALL

DMX4ALL Pixelkonig Wireless ArtNet-DMX STAGE-PROFI... Bedienungsanleitung

DMX4ALL

DMX4ALL DMX Relais/Analog Interface 1 Bedienungsanleitung

DMX4ALL

DMX4ALL DMX-Audio Unit Bedienungsanleitung

DMX4ALL

DMX4ALL Art-Net DMX-UNIVERSE 4.1 Bedienungsanleitung

DMX4ALL

DMX4ALL DMX-Relais/Analog Interface 4 Bedienungsanleitung

DMX4ALL

DMX4ALL Art-Net DMX STAGE-PROFI 1.1 RDM Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch