Dodge Journey 2018 Bedienungsanleitung

2018

JOURNEY

QUICK

REFERENCE

GUIDE

Stadium Tip ’n Slide (7 Passenger

Models)

This feature allows passengers to easily enter or

exit the third-row passenger seats from either side

of the vehicle.

To Move The Second-Row Passenger Seat For-

ward

NOTE:

Raise the 40% seatback/armrest before moving

the 60% seat, to allow for full seat travel.

Move the control lever on the upper outboard side

of the seatback forward. Then, in one fluid motion,

the seat cushion flips upward and the seat moves

forward on its tracks. To Unfold And Move The Second-Row Passenger

Seat Rearward

1. Move the seatback rearward until it locks in

place and then continue sliding the seat rear-

ward on its tracks until it locks in place.

2. Push the seat cushion downward to lock it in

place.

3. Adjust the seat track position as desired.

Rear Seat Lever Locations

1 — Forward/Rearward Adjustment Lever

2 — Recliner/Seatback Release Lever

3 — Tip ’n Slide Control Lever

Seat In Tip ‘n Slide Position

SEATS

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

Comfort Features

Heated Seats

The front heated seats controls are located within

the climate or controls menu screen of the

Uconnect system.

Heated Steering Wheel

The steering wheel contains a heating element

that heats the steering wheel to one temperature

setting. The heated steering wheel control is lo-

cated within the Uconnect system. You can gain

access to the control buttons through the climate

screen or the controls screen.

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

In-Floor Storage Bin With

Removable Liner

An in-floor storage bin is located behind each front

seat.

To Access The Storage Bin

1. Position the front seat to at least a mid-track

position to provide easier access to the storage

bin.

2. Move the floor mat aside (if equipped).

3. Pull the door latch release-loop upward to re-

lease the latch, and then forward to open the

storage bin door.

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

In Floor Storage

CARGO FEATURES

Speed Control

When engaged, the Speed Control takes over

accelerator operations at speeds greater than

25 mph (40 km/h).

The Speed Control buttons are located on the right

side of the steering wheel.

NOTE:

In order to ensure proper operation, the Speed

Control system has been designed to shut down if

multiple Speed Control functions are operated at

the same time. If this occurs, the Speed Control

system can be reactivated by pushing the Speed

Control ON/OFF button and resetting the desired

vehicle set speed.

To Activate

Push the ON/OFF button. The Cruise Control Set

Indicator Light in the instrument cluster display

will illuminate. To turn the system off, push the

ON/OFF button a second time. The Cruise Control

Set Indicator Light will turn off. The system should

be turned off when not in use.

To Set A Desired Speed

Turn the Speed Control on. When the vehicle has

reached the desired speed, push the SET (-) but-

ton and release. Release the accelerator and the

vehicle will operate at the selected speed.

Speed Control Switches

1 — CANCEL

2 — ON/OFF

3 — RES (+)/Resume/Accel

4 — SET (-)/Decel

SPEED CONTROL

To Deactivate

A soft tap on the brake pedal, pushing the CAN-

CEL button, or normal brake pressure while slow-

ing the vehicle will deactivate Speed Control with-

out erasing the set speed memory. Pushing the

ON/OFF button or turning the ignition switch OFF

erases the set speed in memory.

To Resume Speed

To resume a previously set speed, push the

RES (+) button and release. Resume can be used

at any speed above 25 mph (40 km/h).

To Increase Speed

When the Speed Control is set, you can increase

speed by pushing the RES (+) button.

To Decrease Speed

When the Speed Control is set, you can decrease

speed by pushing the SET (-) button.

To Accelerate For Passing

Press the accelerator as you would normally. When

the pedal is released, the vehicle will return to the

set speed.

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

Keyless Enter-N-Go — Passive

Entry

The Keyless Enter-N-Go Passive Entry system is

an enhancement to the vehicle’s Remote Keyless

Entry feature. This feature allows you to lock and

unlock the vehicle's door(s) and liftgate without

having to push the key fob lock or unlock buttons,

as well as starting and stopping the vehicle with

the push of a button.

PASSIVE ENTRY

To Unlock From The Driver Or

Passenger Side

With a valid Keyless Enter-N-Go key fob located

outside the vehicle and within 5 ft (1.5 m) of the

driver or passenger side door handle, grab either

front door handle to unlock the door automatically.

To Lock The Vehicle

Both front door handles have buttons located on

the outside of the handle. With one of the vehicle’s

Keyless Enter-N-Go key fobs located outside the

vehicle and within 5 ft (1.5 m) of the driver's or

passenger front door handle, push the door handle

button to lock all four doors and liftgate.

Do NOT grab the door handle when pushing the

door handle lock button. This could unlock the

door(s).

Preventing Inadvertent Locking Of Passive Entry

Key Fob In Vehicle (FOBIK-Safe)

To minimize the possibility of unintentionally lock-

ing a passive entry key fob inside your vehicle, the

passive entry system is equipped with an auto-

matic door unlock feature which will function if

the ignition switch is in the OFF position.

FOBIK-Safe only executes in vehicles with passive

entry. There are three situations that trigger a

FOBIK-Safe search in any passive entry vehicle:

• A lock request is made by a valid passive entry

key fob while a door is open.

• A lock request is made by the passive entry

door handle while a door is open.

• A lock request is made by the door panel switch

while the door is open

When any of these situations occur, after all open

doors are shut, the FOBIK-Safe search will be

executed. If it finds a passive entry key fob inside

the car, the car will unlock and alert the customer.

NOTE:

The vehicle will only unlock the doors when a valid

passive entry key fob is detected inside the ve-

hicle. The vehicle will not unlock the doors when

any of the following conditions are true:

• The doors are manually locked using the door

lock knobs.

• Three attempts are made to lock the doors

using the door panel switch and then close the

doors.

Grab The Door Handle To Unlock

NOTE:

• After pushing the door handle button, you must

wait two seconds before you can lock or unlock

the doors, using either passive entry door

handle. This is done to allow you to check if the

vehicle is locked by pulling the door handle

without the vehicle reacting and unlocking.

• If passive entry is disabled using Uconnect

System, the key protection described in "Pre-

venting Inadvertent Locking of Passive Entry

Key Fob in Vehicle" remains active/functional.

• The Passive Entry system will not operate if the

key fob battery is dead.

Push The Door Handle Button To Lock Do NOT Grab The Handle When Locking

Lock Or Unlock The Liftgate

With a valid Keyless Enter-N-Go key fob within

5 feet (1.5 meters) of the liftgate, push the elec-

tronic liftgate lock/unlock pad located to the left of

the liftgate handle to unlock the liftgate. Push the

button a second time to lock the liftgate.

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

https://www.mopar.com/en-us/care/

owners-manual.html (U.S. Residents) or

www.owners.mopar.ca (Canadian Residents).

Remote Start — If Equipped

Push the remote start button on the key fob

twice within five seconds. Pushing the remote

start button a third time shuts the engine off.

With Remote Start, the engine will only run for

15 minutes (timeout) unless the keyless ignition is

placed in the ON/RUN position.

Before the end of 15-minute cycle, push and

release the unlock button on the key fob to unlock

the doors and disarm the vehicle security alarm (if

equipped). Then, prior to the end of the 15-

minute cycle, push and release the ignition

START/STOP button.

The vehicle must be started with the key fob after

two consecutive timeouts.

For further information, and applicable

warnings and cautions, please refer

to the Owner’s Manual at

https://www.mopar.com/en-us/care/

owners-manual.html (U.S. Residents) or

www.owners.mopar.ca (Canadian Residents).

Electronic Liftgate Lock/Unlock Pad

REMOTE START

Parkview Rear Back-Up Camera

You can see an on-screen image of the rear of your

vehicle whenever the gear selector is put into

REVERSE. The ParkView Rear Back-Up Camera

image appears on the display screen located on

the center stack of the instrument panel.

NOTE:

If the display screen appears foggy, clean the

camera lens located on the rear of the vehicle

above the license plate.

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

Instrument Cluster Display

The instrument cluster display features a driver

interactive display that is located in the instru-

ment cluster. Pushing the controls on the left side

of the steering wheel allows the driver to select

vehicle information and Personal Settings.

• Push the up arrow button to scroll upward

through the main menus (Fuel Economy, Ve-

hicle Speed, Trip Info, Vehicle Info, Messages,

Units, System Set-Up, Turn Menu Off) and sub

menus.

• Push the down arrow button to scroll downward

through the main menus and sub menus.

• Push the right arrow button for access to main

menus, sub menus or to select a personal

setting in the setup menu.

• Push the BACK button to scroll back to a previ-

ous menu or sub menu.

Instrument Cluster Display Controls

SAFETY FEATURES INSTRUMENT CLUSTER

DISPLAY

Selectable Menu Items

The instrument cluster features a driver interac-

tive display that is located in the of the center of

the instrument cluster. Pushing the controls on

the left side of the steering wheel allows the driver

to select vehicle information and Personal Set-

tings. Push the up or down arrow buttons to scroll

through the main menu feature items. To enter the

submenu’s of a feature menu item, push the right

arrow button then push the right arrow button to

select or reset the submenu feature items:

Radio Info Tire Pressure

Vehicle Info Messages

Fuel Economy Vehicle Speed

Trip Info Turn Menu Off

For further information, and applicable warnings and

cautions, please refer to the Owner’s Manual at

www.mopar.com/en-us/care/owners-manual.html

(U.S. Residents) or www.owners.mopar.ca (Cana-

dian Residents).

AUTO Button

• Push the AUTO button on the Integrated Center

Stack (ICS) Climate Controls, OR on the radio

touchscreen when viewing the Climate Controls

Main Screen.

• Select the desired temperature by pushing the

up or down temperature buttons for the driver

or passenger.

• The system will maintain the set temperature

automatically.

Uconnect 3/3 NAV With 8.4–inch Display

Automatic Climate Controls

AUTOMATIC CLIMATE

CONTROLS

Andere Handbücher für Journey 2018

Inhaltsverzeichnis

Andere Dodge Automobil Handbücher

Dodge

Dodge 2009 Journey Technisches Datenblatt

Dodge

Dodge 2004 DR Ram SRT-10 Bedienungsanleitung

Dodge

Dodge Avenger Bedienungsanleitung

Dodge

Dodge DURANGO 2021 Bedienungsanleitung

Dodge

Dodge challenger 2017 Bedienungsanleitung

Dodge

Dodge 2013 Grand Caravan Bedienungsanleitung

Dodge

Dodge 2015 Dart Bedienungsanleitung

Dodge

Dodge Ram Truck 2010 Bedienungsanleitung

Dodge

Dodge Journey Bedienungsanleitung

Dodge

Dodge Avenger 2011 Bedienungsanleitung

Dodge

Dodge Avenger 2011 Bedienungsanleitung

Dodge

Dodge 2015 Charger POLICE Konfigurationshandbuch

Dodge

Dodge Challenger 2019 Bedienungsanleitung

Dodge

Dodge Viper 2014 SRT Bedienungsanleitung

Dodge

Dodge CUSTOM ROYAL 1957 Bedienungsanleitung

Dodge

Dodge Durango Bedienungsanleitung

Dodge

Dodge Ram Truck 1500 Bedienungsanleitung

Dodge

Dodge RAM 2500 2009 Bedienungsanleitung

Dodge

Dodge RAM 2500 2022 Bedienungsanleitung

Dodge

Dodge CHARGER Hellcat 2017 Bedienungsanleitung

Dodge

Dodge DURANGO 2017 Bedienungsanleitung

Dodge

Dodge RAM 1500 Series Bedienungsanleitung

Dodge

Dodge 2011 Dodge Challenger SRT8 392 Bedienungsanleitung

Dodge

Dodge DURANO 2009 Bedienungsanleitung

Beliebte Automobil Handbücher anderer Marken

Toyota

Toyota 2000 Tundra Bedienungsanleitung

CITROËN

CITROËN DS4 DSign Bedienungsanleitung

Lexus

Lexus 2015 CT 200h Bedienungsanleitung

Cadillac

Cadillac CTS 2008 Bedienungsanleitung

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Bedienungsanleitung

Porsche

Porsche Boxster S Bedienungsanleitung

GMC

GMC 2010 Savana 1500 Cargo Bedienungsanleitung

KIAM

KIAM SPORTAGE 2014 Stücklistenhandbuch

GMC

GMC 2013 Terrain Montageanleitung

GMC

GMC T-Series 1999 Bedienungsanleitung

Mercury

Mercury 1998 Mystique Bedienungsanleitung

Mercury

Mercury 2007 Mariner Bedienungsanleitung

Mazda

Mazda 2007 Mazdaspeed 3 Leitfaden

Mazda

Mazda 2014 CX-5 Bedienungsanleitung

GMC

GMC Chevrolet Express 2022 Bedienungsanleitung

GMC

GMC 1997 Jimmy Bedienungsanleitung

Chevrolet

Chevrolet 2012 Malibu Bedienungsanleitung

Cadillac

Cadillac 2010 Escalade Bedienungsanleitung