Dodge TXT Bedienungsanleitung
1
Dodge® TXT & TDT Cooling Fans
Instruction Manual
Sizes: TXT505A, TXT5C, TXT6–TXT12, TDT6–TDT15, T19
These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of
printing. Please see dodgeindustrial.com for updated instruction manuals.
WARNING: To ensure the drive is not unexpectedly started, turn o and lock-out or
tag power source before proceeding. Failure to observe these precautions could
result in bodily injury.
WARNING: Because of the possible danger to person(s) or property from accidents which may result from the improper use of products, it is important that correct
procedures be followed. Products must be used in accordance with the engineering information specied in the catalog. Proper installation, maintenance and
operation procedures must be observed. The instructions in the instruction manuals must be followed. Inspections should be made as necessary to assure safe
operation under prevailing conditions. Proper guards and other suitable safety devices or procedures as may be desirable or as may be specied in safety codes
should be provided, and are neither provided by Dodge nor are the responsibility of Dodge. This unit and its associated equipment must be installed, adjusted and
maintained by qualied personnel who are familiar with the construction and operation of all equipment in the system and the potential hazards involved. When risk to
persons or property may be involved, a holding device must be an integral part of the driven equipment beyond the speed reducer output shaft.
WARNING: All products over 25 kg (55 lbs) are noted on the shipping package.
Proper lifting practices are required for these products.
X
X
“B” “B”
“B”
X
X
X
X
X
TXT6
TXT705, 805
TXT605
TXT5C, 505A
TXT7
“B”
X
X
TXT8, 9, 10, 905 “B”
TXT12
TDT13, 14, 15
X - Remove bolts marked “X”
X
X
X
X
X
X
X
INSTALLATION
1. Examine all parts for possible damage during shipping.
Insure that all parts are free of any foreign materials prior to
assembly.
2. Remove every other bolt in the input shaft seal carrier and set
aside. Refer to Figure 1 for bolts to be removed.
3. Set shroud mounting straps in place and reinstall input shaft
seal carrier bolts until nger tight. Mount fan shroud so that it
is centered and align mounting straps. Remove shroud and
tighten carrier bolts to recommended torque in Table 1.
Note: It is important that straps do not move after they are
aligned.
4. Place safety screen on shaft against straps. Place fan blade
on input shaft with fan blade edge distance 'A' (Figure 2 and
Table 1) from end of shaft. Install set screws in fan blade hub
and tighten securely
5. Mount fan shroud making sure it is centered and install bolts
through shroud and safety screen. Install lockwashers and
hex nuts, tightening securely.
6. Check clearance between fan blades and shroud to insure
that they do not touch.
Table 1
Size A B Torque (lb-ins)
TXT505A 1-11/16 0360
TXT5C 3-11/16 0360
TDT6, TXT6A 3-3/4 1-3/4 360
TDT7, TXT7A 42-3/16 600
TDT8, TXT8A 4-1/2 2-3/16 360
TDT9, TXT9A 6-11/16 3-3/4 360
TDT10, TXT10A 6-1/2 2-1/4 360
TDT12, TXT12 6-1/4 3-1/4 1800
TDT13 6-1/16 3-15/16 1800
TDT14 92-13/16 3120
TDT15 9-7/8 23120
TXT605 3-11/16 0360
TXT705 4-3/16 0360
TXT805 4-33/64 0360
TXT905 6-15/16 0360
Figure 1 - Bolt Removal
A
Figure 2 - Fan Blade Safety Screen Placement
Dodge Industrial, Inc.
6040 Ponders Court
Greenville, SC 29615
Ph: 1.864.297.4800
© Dodge Industrial, Inc.
MN1635 (Replaces 499365)
All Rights Reserved. Printed in USA.
11/21
*1635-1121*
Reference Description Qty
Required
Part Numbers
TXT505A TXT5C TDT6, TXT6A TDT7, TXT7A TDT8, TXT8A TDT9, TXT9A
Cooling Fan Assembly ①1255231 272369 272325 272326 272327 272328
1② Fan Blade 1255232 272415 272334 272335 272335 272336
2②Fan Shroud 1255233 272422 272344 272346 272346 272347
3② Mounting Strap ③255234 245636 272353 272354 272355 272356
4②Set Screw 2400026 400026 400026 400086 400086 400094
5②Cap Screw ③411394 411394 411409 411409 411409 411407
6 ② Lockwasher ③419009 419009 419011 419011 419011 419011
7②Hex Nut 1407083 407083 407087 407087 407087 407087
8Safety Screen 1 - - 242750 242751 242751 242753
9② Bracket ④255235 255235 - - - -
10 ② Bracket Screw ④411022 411022 - - - -
11 ② Lock Washer ④419077 419077 - - - -
12 ②Fan Key 1443112 443112 - - - -
13 ②Shaft Key 1443094 443094 - - - -
Reference Description Qty
Required
Part Numbers
TDT10, TXT10A TDT12, TXT12 TDT13 TDT14 TDT15 T19
Cooling Fan Assembly 1272329 272330 272331 272332 272333 272324
1②Fan Blade 1272337 272337 272338 272338 272339 272335
2②Fan Shroud 1272347 272347 272348 272348 272348 272346
3② Mounting Strap ③272356 272357 272361 272358 272359 272360
4②Set Screw 2400090 400090 400154 400154 400146 400086
5②Cap Screw ③411407 411407 411407 411407 411407 411409
6 ② Lockwasher ③419011 419011 419011 419011 419011 419011
7②Hex Nut 1407087 407087 407087 407087 407087 407087
8Safety Screen 1242753 424753 242756 242756 242756 242753
9② Bracket ④- - - - - -
10 ② Bracket Screw ④- - - - - -
11 ② Lock Washer ④- - - - - -
12 ②Fan Key 1 - - - - - -
13 ②Shaft Key 1 - - - - - -
①Assembly includes parts listed immediately below.
②Included in assemblies under which they are listed.
③2 required on size TXT505A; 3 rquired on sizes TXT5B, TDT6 & 7; 4 required on sizes TDT8 – 15 & T19.
④2 required on size TXT505A; 3 rquired on size TXT5B.
8
1
67
3
4
2
5
Replacement Parts for Cooling Fan
Dieses Handbuch passt für folgende Modelle
20
Andere Dodge Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
