Dolmar AC3611 Bedienungsanleitung

AC3611

EN Cordless Multi Function

Power Head INSTRUCTION MANUAL 5

Bezprzewodowa

Wielofunkcyjna Jednostka

Napędowa INSTRUKCJA OBSŁUGI 13

HU Vezeték nélküli többfunkciós

alapgép HASZNÁLATI KÉZIKÖNYV 22

SK Akumulátorová multifunkčná

motorová jednotka NÁVOD NA OBSLUHU 31

CS Akumulátorová multifunkční

motorová jednotka NÁVOD K OBSLUZE 39

Акумуляторний

багатофункціональний

приводний інструмент

ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 47

RO Cap cu motor universal fără

cablu MANUAL DE INSTRUCŢIUNI 56

DE Multifunktions-Antrieb BETRIEBSANLEITUNG 65

10 11

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

5ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: AC3611

No load speed

(without attachment)

Low 0 - 5,700 min-1

Medium 0 - 8,200 min-1

High 0 - 9,700 min-1

Overall length 1,011 mm

Rated voltage D.C. 36 V

Net weight 5.2 kg - 11.7 kg

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may di󰀨er from country to country.

• The weight may di󰀨er depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge

BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B

• Some of the battery cartridges listed above may not be available depending on your region of residence.

WARNING:

Only use the battery cartridges listed above. Use of any other battery cartridges may cause injury and/or re.

No load speed with attachment

Model Rotation speed

Low Medium High

BC-AC, EM401MP 0 - 4,200 min-1 0 - 6,000 min-1 0 - 7,100 min-1

EM404MP, EM406MP 0 - 3,500 min-1 0 - 5,000 min-1 0 - 6,000 min-1

HT-CS 1, HT-CS 2, HT-CS 3,

EN401MP, EN410MP, EN420MP

(Strokes per minute)

0 - 2,400 min-1 0 - 3,400 min-1 0 - 4,000 min-1

PS-CS 1, EY401MP (chain speed) 0 - 12 m/s 0 - 17 m/s 0 - 20 m/s

MC-CS, KR400MP 0 - 160 min-1 0 - 230 min-1 0 - 280 min-1

MC-CS1, KR401MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1

PE-CS, EE400MP 0 - 2,800 min-1 0 - 4,000 min-1 0 - 4,700 min-1

CH-CS, EJ400MP 0 - 1,600 min-1 0 - 2,300 min-1 0 - 2,800 min-1

MB-CS, BR400MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1

MW-CS, SW400MP 0 - 130 min-1 0 - 190 min-1 0 - 230 min-1

AG-CS, UB400MP 0 - 5,700 min-1 0 - 7,850 min-1 0 - 8,250 min-1

Approved attachment

Type Model

Brushcutter attachment BC-AC, EM401MP, EM404MP

String trimmer attachment EM406MP

Hedge trimmer attachment HT-CS 1, HT-CS 2, EN401MP, EN410MP

Ground trimmer attachment HT-CS 3, EN420MP

Pole saw attachment PS-CS 1, EY401MP

Cultivator attachment MC-CS, MC-CS1, KR400MP, KR401MP

Edger attachment PE-CS, EE400MP

Co󰀨ee harvester attachment CH-CS, EJ400MP

Shaft extension attachment SE-CS, LE400MP

Power brush attachment MB-CS, BR400MP

Power sweep attachment MW-CS, SW400MP

6ENGLISH

Type Model

Blower attachment AG-CS, UB400MP

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Read instruction manual.

Take particular care and attention.

Do not expose to moisture.

Ni-MH

Li-ion

Only for EU countries

Do not dispose of electric equipment or battery

pack together with household waste material!

In observance of the European Directives,

on Waste Electric and Electronic Equipment

and Batteries and Accumulators and Waste

Batteries and Accumulators and their imple-

mentation in accordance with national laws,

electric equipment and batteries and battery

pack(s) that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility.

Intended use

This cordless multi function power head is intended for driving an

approved attachment listed in the section "SPECIFICATIONS" of

this instruction manual. Never use the unit for the other purpose.

WARNING: Read the instruction manual of

the attachment as well as this instruction manual

before using. Failure to follow the warnings and

instructions may result serious injury.

Noise

Attachment Sound pressure level

average

Sound power level

average

Applicable

standard

LPA (dB (A))

Uncertainty K

(dB (A))

LWA (dB (A))

Uncertainty K

(dB (A))

BC-AC, EM401MP

(as a brushcutter)

78.5 1.0 90.2 1.5 EN11806

BC-AC, EM401MP

(as a string trimmer)

Nylon cutting head 84.3 0.6 93.3 1.6 EN50636

Plastic blade 77.0 1.7 88.5 1.8 EN50636

EM404MP (as a brushcutter) 82.5 2.2 93.3 2.9 EN11806

EM404MP (as a string trimmer) Nylon cutting head 84.7 2.3 92.8 1.6 EN50636

Plastic blade 76.0 1.8 87.7 1.5 EN50636

EM406MP Nylon cutting head 84.7 2.5 93.5 2.2 EN50636

Plastic blade 77.0 1.9 85.6 2.0 EN50636

HT-CS 1, EN401MP 83.7 1.2 92.6 0.7 ISO10517

HT-CS 1 + SE-CS

EN401MP + LE400MP

83.7 1.3 92.8 1.1 ISO10517

HT-CS 2, EN410MP 80.2 1.9 88.2 2.2 ISO10517

HT-CS 2 + SE-CS

EN410MP + LE400MP

78.9 1.7 88.3 2.7 ISO10517

HT-CS 3, EN420MP 84.0 0.8 94.0 0.7 ISO10517

PS-CS 1, EY401MP 92.5 1.4 101.9 1.4 ISO11680

PS-CS 1 + SE-CS

EY401MP + LE400MP

86.6 1.0 101.2 1.0 ISO11680

MC-CS, KR400MP 76.7 2.2 84.2 1.0 EN709

MC-CS1, KR401MP 73.1 1.4 84.2 1.8 EN709

PE-CS, EE400MP 74.8 1.5 88.2 2.6 ISO11789

CH-CS, EJ400MP 87.4 1.4 94.5 1.3 ISO10517

CH-CS + SE-CS

EJ400MP + LE400MP

85.6 1.0 95.5 1.3 ISO10517

MB-CS, BR400MP 79.5 0.9 89.0 0.7 EN60335

MW-CS, SW400MP 80.1 1.8 88.8 0.7 EN60335

AG-CS, UB400MP 89.8 0.4 100.4 0.8 EN50636

7ENGLISH

• Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB

(A). Wear ear protection.

Vibration

Attachment Left handle (Front grip) Right handle (Rear grip) Applicable

standard

ah (m/s2)

Uncertainty K

(m/s2)

ah (m/s2)

Uncertainty K

(m/s2)

BC-AC, EM401MP

(as a brushcutter)

3.0 1.5 2.5 1.5 EN11806

BC-AC, EM401MP

(as a string trimmer)

Nylon cutting head 5.0 1.5 2.5 1.5 EN50636

Plastic blade 2.5 1.5 2.5 1.5 EN50636

EM404MP (as a brushcutter) 3.0 1.5 2.5 1.5 EN11806

EM404MP (as a string trimmer) Nylon cutting head 3.0 1.5 2.5 1.5 EN50636

Plastic blade 2.5 1.5 2.5 1.5 EN50636

EM406MP Nylon cutting head 2.5 1.5 2.5 1.5 EN50636

Plastic blade 4.0 1.5 2.5 1.5 EN50636

HT-CS 1, EN401MP 5.5 1.5 3.5 1.5 ISO10517,

EN60745

HT-CS 1 + SE-CS

EN401MP + LE400MP

5.5 1.5 4.0 1.5 ISO10517,

EN60745

HT-CS 2, EN410MP 4.0 1.5 2.5 1.5 ISO10517,

EN60745

HT-CS 2 + SE-CS

EN410MP + LE400MP

4.5 1.5 2.5 1.5 ISO10517,

EN60745

HT-CS 3, EN420MP 6.5 1.5 4.0 1.5 ISO10517

PS-CS 1, EY401MP 2.5 1.5 2.5 1.5 ISO11680

PS-CS 1 + SE-CS

EY401MP + LE400MP

5.5 1.5 2.5 1.5 ISO11680

MC-CS, KR400MP 2.5 1.5 2.5 1.5 EN709

MC-CS1, KR401MP 2.5 1.5 2.5 1.5 EN709

PE-CS, EE400MP 2.5 1.5 2.5 1.5 ISO11789

CH-CS, EJ400MP 4.0 1.5 3.0 1.5 ISO10517

CH-CS + SE-CS

EJ400MP + LE400MP

4.5 1.5 3.0 1.5 ISO10517

MB-CS, BR400MP 2.5 1.5 2.5 1.5 EN60335

MW-CS, SW400MP 2.6 1.5 2.6 1.5 EN60335

AG-CS, UB400MP 4.5 2.0 2.5 1.5 EN50636

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can di󰀨er from the declared

value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the

times when the tool is switched o󰀨 and when it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

8ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o󰀨 open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may result in poor performance or

breakdown of the tool or battery cartridge.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

9ENGLISH

PARTS DESCRIPTION

► Fig.1

1Battery cartridge 2Lock-o󰀨 lever 3Switch trigger 4Hanger

5Handle 6Release button 7Barrier (country specic) 8Speed indicator

9Power lamp 10 Main power button 11 Reverse button 12 Shoulder harness

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before adjusting or checking function on the tool.

Failure to switch o󰀨 and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

Installing or removing battery

cartridge

CAUTION: Always switch o󰀨 the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip o󰀨 your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► Fig.2: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts o󰀨 power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Status Indicator lamps

On O󰀨 Blinking

Overload

Overheat

Over

discharge

Overload protection

If the tool is overloaded by entangled weeds or other

debris, and the middle indicators start blinking and

the tool automatically stops.

In this situation, turn the tool o󰀨 and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

Overheat protection for tool or

battery

When a over heating occurs, all speed indicators blink.

If the overheating occurs, the tool stops automatically.

Let the tool and/or battery cool down before turning the

tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and indicator blinks.

If the tool does not operate even when the switches are

operated, remove the batteries from the tool and charge

the batteries.

10 ENGLISH

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

► Fig.3: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted O󰀨 Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may di󰀨er slightly

from the actual capacity.

Main power switch

WARNING: Always turn o󰀨 the main power

switch when not in use.

To stand by the tool, press the main power button until the main

power lamp lights up. To turn o󰀨, press the main power button again.

► Fig.4: 1. Main power button

NOTE: The main power lamp brinks if the switch

trigger is pulled under unoperatable conditions. The

lamp blinks if you turn on the main power switch while

holding down the lock-o󰀨 lever and the switch trigger.

NOTE: This tool employs the auto power-o󰀨 function.

To avoid unintentional start up, the main power switch

will automatically shut down when the switch trigger

is not pulled for a certain period after the main power

switch is turned on.

Switch action

WARNING: For your safety, this tool is

equipped with lock-o󰀨 lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-o󰀨 lever. Return the

tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-o󰀨 lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-o󰀨 lever. This can cause

switch breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-o󰀨 lever is provided.

► Fig.5: 1. Lock-o󰀨 lever 2. Switch trigger

To start the tool, turn on the main power switch and

grasp the handle (the lock-o󰀨 lever is released by the

grasp) and then pull the switch trigger. Tool speed is

increased by increasing the pressure on the switch

trigger. To stop the tool, release the switch trigger.

Speed adjusting

You can adjust the tool speed by tapping the main

power button.

Each time you tap the main power button, the level of

speed will change.

► Fig.6: 1. Main power button

Indicator Mode

High

Medium

Low

Reverse button for debris removal

WARNING: Switch o󰀨 the tool and remove

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation

function can not remove. Failure to switch o󰀨 and

remove the battery cartridge may result in serious

personal injury from accidental start-up.

This tool has a reverse button to change the direction of

rotation. It is only for removing weeds and debris entan-

gled in the tool.

To reverse the rotation, tap the reverse button and pull

the trigger when the tool’s head is stopped. The power

lamp starts blinking, and the tool's head rotates in

reverse direction when you pull the switch trigger.

To return to regular rotation, release the trigger and wait

until the tool's head stops.

► Fig.7: 1. Reverse button

Andere Handbücher für AC3611

Inhaltsverzeichnis

Sprachen:

Andere Dolmar Zubehör für Elektrowerkzeuge Handbücher

Dolmar

Dolmar SE-CS Bedienungsanleitung

Beliebte Zubehör für Elektrowerkzeuge Handbücher anderer Marken

Bosch

Bosch OSC004 Bedienungsanleitung

Rockler

Rockler 57510 Bedienungsanleitung

Bosch

Bosch RA1054 Montageanleitung

Grizzly

Grizzly T10808 Bedienungsanleitung

Kitagawa

Kitagawa SC N Series Bedienungsanleitung

Wolfcraft

Wolfcraft FKS 145 Kurzanleitung

ADAMAS

ADAMAS B32 Bedienungsanleitung

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Bedienungsanleitung

Echo

Echo Speed-Feed Universal 400 LH/RH Bedienungsanleitung

SCHUNK

SCHUNK ROTA TB-TBS-EP Gebrauchsanweisung

Schmid

Schmid RAPID Secure XL Bedienungsanleitung

Drill Master

Drill Master 360X Bedienungsanleitung

Toro

Toro 138-5050 Bedienungsanleitung

jbc

jbc SF-SD Bedienungsanleitung

Bosch

Bosch GTA 3800 Professional Montageanleitung

RG AVAK

RG AVAK MaxDrill Series Bedienungsanleitung

infaco

infaco PW3 Bedienungsanleitung

Gloria

Gloria CUT & BRUSH Bedienungsanleitung