Dometic EA3100 Bedienungsanleitung

207.5166.20

EA 3100 EA 3080 EA 3140

RA 80 RA 140

RH 200

miniCool

Operating Instructions

Thank you for choosing our appliance. We are sure it will provide you with trouble free use.

In the following, we would like to familiarise you with some symbols, which we bring to your attention to ensure

the safe and efficient operation of the appliance:

source of danger, in event of improper operation

suggested useful tips to read

information concerning environmental protection

This refrigerator is intended for the storage of food and drinks.

Attention!

This product is designed to be operated by adults. Children should not be

allowed to tamper with the controls or play with the product.

Any electrical work required to install this appliance should be carried out by a

qualified electrician.

This product should be serviced by an authorised Service ngineer, and only

genuine spare parts should be used.

It is dangerous to alter the specifications or modify this product in any way.

Care must be taken to ensure that the appliance does not stand on the

electrical supply cable.

There are working parts in this product which heat up. Always ensure that there

is adequate ventilation as a failure to do this will result in component failure

and possible content loss. See installation instructions.

Parts which heat up should not be exposed. Wherever possible the back of the

product should be close to a wall but leaving the required distance for

ventilation as stated in the installation instructions.

Before defrosting, cleaning or maintenance work is carried out, be sure to

switch off the appliance and unplug it.

DO NOT US SHARP INSTRUM NTS to scrape off frost or ice. Under no

circumstances should solid ice be forced off the cooling fins. Solid ice should

be allowed to thaw when defrosting the appliance. See defrost instructions.

This appliance is heavy. Care should be taken when moving it.

Under no circumstances should you attempt to repair the appliance yourself.

Repairs carried out by inexperienced persons may cause injury or more serious

malfunctioning. Refer to your local Service Centre and always insist on

genuine spare parts.

In this appliance the storage of any toxic or explosive substance is forbidden!

Please read these operating instructions carefully before putting the

refrigeration unit into operation. If you later sell or dispose of it, please ensure

that the new owner receives these operating instructions.

Please follow the installation details below carefully Guarantee is valid for

products installed as described only. (See chapter 4.1)

CONT NT

CONT NTS

1. Unpacking

2. View of the appliance

3. Cleaning

4. Positioning the appliance

4.1. Installation instruction

5. Using the appliance

5.1. Temperature regulation

6. Ice cubes

7. Useful suggestions

8. Defrosting, cleaning and maintenance

9. Changing the lightbulb

10. Reversing the door hang

11. Replacing the decorative door panel

12. Assembly of door handle

13. Changing the feet

14. Customer service

15. Putting into operation, technical data

15.1. Connecting to electrical mains

16. Environmental protection information

17. Recycling

1. Unpacking

After removal from the cardboard packaging, make

sure the appliance is not damaged. If you find damage

to the appliance resulting from transport, report it

immediately to the transportation firm.

2. View of the appliance

1. Door lock

2. Sensor

3. Thermostat knob

4. Evaporator

5. Lamp (if available)

Figure 1.

IN CAS IF YOUR R FRIG RATOR IS QUIPP D WITH LOCK, DOM TIC RT DO NOT ACC PT

LIABILITY FOR LOSS OR DAMAG OF K YS. HOW V R W WOULD B HAPPY TO SUPPLY A

COMPL T LOCK AND K Y R PLAC M NT.

EA 3100 EA 3080

EA 3140

3. Cleaning

Clean the refrigerator thoroughly at intervals, as

necessary. Remove the shelves; these, the

cabinet interior and the door should be washed with a

warm solution of sodium bi carbonate. Finally wipe

over with a cloth rinsed in warm water only, and dry

with a clean cloth. Do not wash any plastic parts in

water that is more than hand warm, and do not expose

them to dry heat. The outside of the cabinet should be

wiped down regularly with a clean, damp cloth.

NEVER USE STRONG CHEMICALS OR ABRASIVE

CLEANING MATERIALS ON ANY PART OF THE

CABINET.

4. Positioning the appliance

When first using this refrigerator please consider the

following points:

ENSURE REFRIGERATOR IS LEVEL

THE PIPEWORK AT THE BACK GETS HOT IN USE

THE REFRIGERATOR HAS NO 'MOTOR' AND IS

THEREFORE VIRTUALLY SILENT

ALLOW AT LEAST 3 HRS. FOR SIGNS OF

COOLING

During the refrigeration process, the appliance

gives off heat from the condenser (under the

upper part of the rear cover) into the surrounding air.

The more ventilated the condenser is, the more

effective the refrigeration will be.

The other condition for satisfactory operation is that

the appliance stands on a flat surface. This is best

seen by placing a glass of water on top of the

appliance.

It is important that the appliance is not directly

exposed to radiated heat (sunlight, radiator, near an

oven, etc.).

4.1. Installation instructions

The refrigerator is equipped with an electrically heated

absorption cooling unit which is virtually silent in

operation. The fridge is designed for free standing

installation, but can be built in if the following

conditions are complied with to ensure satisfactory

operation and maximum cooling efficiency.

IMPORTANT

Please follow the installation details below

carefully Guarantee is valid for products installed

as described only.

1. The refrigerator must be level both directions

2. There should be 20mm clearance to the wall

Figure 2.

3. Ventilation must be provided as shown in

alternatives A, B, C or D (fig 2-3)

4. The ventilation duct must at least measure

105mm x the width of the refrigerator

5. Only the entire cooling unit must project into

the duct as shown

6. Air passing through the duct must not be

preheated by any source of heat

7. Ventilation grills, if used, must have openings

of at least 200cm2 each

During installation, please ensure the mains plug

is accessible at all times.

5. Using the appliance

To start the refrigerator connect the plug to the socket

outlet and switch on the socket. The cooling fins

should show signs of cooling after about 3 hours.

The refrigerator needs about 6 hours at normal

ambient temperature to reach 6 °C in the storage

compartment.

5.1. Temperature regulation

The usual setting required is in the region of 2 to 3 on

the thermostat knob (Fig. 4), but this can vary with

conditions of load and installation. If it is found

necessary to alter the setting,the knob can be turned

to a higher number to produce a colder temperature,

or a lower number to produce a warmer temperature.

The effect of any adjustment can be checked by

means of the thermometer after leaving the

refrigerator operating for a further period to settle

down again.

Figure 4.

Figure 3.

6. IC CUB S

Fill the ice tray to 4/5 with drinking water, cover with

the lid and place the closed ice tray on the ice tray

shelf. Wipe off any excess water to prevent the ice tray

from freezing to the surface.

To speed up the making of ice cubes, turn the

thermostat to position 5 for a short while. Remember

to turn the dial to its normal setting when the ice cubes

are frozen.

To remove the cubes from the ice tray, hold it under

running water. Remove the lid with the ice cubes from

the ice tray and the ice cubes can now be taken out

easily.

7. Useful suggestion

Do not overfill the appliance. It is advisable to leave

some space between the products in the cabinet to

ensure efficient and even cooling. If the shelves are

packed too tightly there may be unacceptable

temperature variations.

8. Defrosting, cleaning and

maintenance

Frost will gradually form on the cooling surfaces and it

must not be allowed to become too thick since it acts

as an insulator and interferes with the cooling.

This frost formation is kept back by the FUZZY LOGIC

system built into the appliance by switching off the unit

for two hours in every 24 hours. The frost will melt and

the defrost water will run through the drain tube from

the drip channel into an evaporating vessel located at

the bottom rear of the refrigerator. (Fig 5) The defrost

water will evaporate automatically into the circulating

air and the vessel will not need emptying manually.

If we want to switch off the unit, turn the thermostat

knob to "0", disconnect the refrigerator from the

electricity supply and leave the cabinet door open.

After defrosting the cabinet interior should be wiped

out with a clean, damp cloth.

9. Changing the lightbulb (If available)

If the lightbulb needs changing, pull out the plug and

proceed as follows:

Press the metal reflector to one side and draw the

lamp covering backwards. Replace the bulb and push

the covering back into place.

A new 10 watt bulb can be obtained at any service

shop.

10. Reversing the door hang, Fig. 6

Lay the appliance on its back. Remove the 8 screws

(1). Remove the door, together with the two hinges

(2), from the housing.

Remove the two cover caps (3) from the housing and

place them in the open hinge holes in the housing.

Place the bottom righthand hinge in the top left of the

door and the top righthand hinge in the bottom left of

the door and hang the door on its hinges in the open

Figure 5.

Figure 6.

cover cap holes in the housing. Secure the hinges

and cover caps with the 8 screws.

Check that the door closes easily and is sealed

properly.

11. Replacing the decorative

door panel, Fig. 7-9

Remove the two screws (1) from the upper hinge of

the door.

Pull the door together with the hinge away from the

housing and up off the lower hinge bolt (2 3).

Remove screws (4) and pull off the frame edge (5).

Slide the decorative panel (6) out of the door frame

and insert the new panel (7), so that the upper edge

of the panel runs exactly parallel to the upper edge of

the frame. A new panel can be inserted more easily

into the upper edge of the frame when the two corners

are cut off by approx. 5 x 5mm (8). Put the frame edge

(5) back in place and secure with screws.

Place the door on the lower hinge (9), slot the upper

hinge into the opening, press together with the door

against the housing and secure with the two screws

(11).

12. Assembly of door handle

(Fig. 10)

Figure 7.

Figure 8.

Figure 9

Figure 10

13. Changing the feet

Should you wish to install your miniCool, you will not

need the 40 mm feet. After having removed the 40

mm feet, you can then re attach the 12 mm feet,

located inside the 40 mm feet, to the front and rear

fixing points. The 40 mm feet and the 4 remaining

screws should be retained for future use.

14. Customer service

Before you call a service engineer, carry out the

following simple tests:

Is there a power failure? Check the fuses.

Is the plug firmly connected to the socket and is the

socket switched on? Check the socket by plugging

in another appliance, e.g. a table lamp.

Is the thermostat at the correct setting? (normally 3

or 4).

Has the door not been closed properly causing the

inside temperature to rise too quickly?

Is the refrigerator level?

Has the ventilation become obstructed?

If after checking all the above points, the refrigerator

is still not working satisfactorily, contact your nearest

service engineer. State the problem, model, product

and serial number.

(Details of the model, product and serialnumber are

to be found on the data label in the top left of the

inside compartment.)

This refrigerator is equipped with overheating

protection. An authorised service technician can

check whether this has been triggered or not.

In the event of a fault developing, contact your

nearest Service Centre see local telephone directory.

15. Putting into operation

Technical data:

Model EA 3100 EA 3080 EA 3140

RA 80; RH 200 RA 140

Type MF20-60 MF20-60 MF20-60

Gross volume 31 litre 23 litre 41 litre

M ins oper tion 100V (AC) 100V (AC) 100V (AC)

Input 90W 90W 90W

Energy consumption 0.97 kWh/24h 0,92 kWh/24h 1.07 kWh/24h

Clim te cl ss N N N

Refriger nt 245g NH3+ H2O 245g NH3+ H2O 245g NH3+ H2O

Figure 11

15.1 Connecting to electrical mains

The appliance may only be operated from

nominal voltage mains as shown on the data

plate. The appliance mains plug may be connected to

a mains socket earthed in accordance with

regulations.

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

The manufacturer declines any liability should

these safety measures not be observed.

lectrical Requirements

Before switching on, make sure the electricity supply

voltage is the same as that indicated on the appliance

rating plate.

16. nvironmental protection

information

The appliance does not contain any CFCs/HCFCs.

Ammonia (natural hydrogen and nitrogen compound)

is used as a refrigerating agent in the refrigeration unit.

The ozone friendly cyclopentane is activated as a

motive agent for the PU foam insulation.

Sodium chromate is used for corrosion protection

(less than 2 weight % of the coolant).

17. Recycling

After unpacking the appliance, the packing materials

should be delivered to a local collection site. At the

end of its useful lifetime, the appliance should be

delivered to a specialized collection and reprocessing

firm, which reclaims the usable materials. The rest is

properly destroyed.

This appliance complies with the following C

directives:

LVD Directive 73/23/EEC with amendment

90/683/EEC

EMC Directive 89/336/EEC

Andere Handbücher für EA3100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic TCW 3000 SDD Montage- und Bedienungsanleitung

Dometic

Dometic DMH1072 Bedienungsanleitung

Dometic

Dometic RM 4223 Handbuch

Dometic

Dometic ABSORPTION RMD 8501 Bedienungsanleitung

Dometic

Dometic CRD0050 Bedienungsanleitung

Dometic

Dometic RM 5380 Bedienungsanleitung

Dometic

Dometic CFF12 Bedienungsanleitung

Dometic

Dometic HIPRO CARE A30 Bedienungsanleitung

Dometic

Dometic DM20F Bedienungsanleitung

Dometic

Dometic RM 122F Technisches Datenblatt

Dometic

Dometic RMV 5301 Bedienungsanleitung

Dometic

Dometic DE15F Bedienungsanleitung

Dometic

Dometic DM Series Bedienungsanleitung

Dometic

Dometic RM2612 Montageanleitung

Dometic

Dometic miniCool EA 3210 Bedienungsanleitung

Dometic

Dometic A40S1 Bedienungsanleitung

Dometic

Dometic RC1700 EGP Bedienungsanleitung

Dometic

Dometic 9 SERIES Bedienungsanleitung

Dometic

Dometic RMS 8465 Bedienungsanleitung

Dometic

Dometic RMD 8501 Bedienungsanleitung

Dometic

Dometic CRX110 Bedienungsanleitung

Dometic

Dometic CFF12 Bedienungsanleitung

Dometic

Dometic RM 2355 and Bedienungsanleitung

Dometic

Dometic RM2351 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung