Dometic HiPro 3000 Bedienungsanleitung

Type H20 / 60

821 2660-01

ENGLISH

miniBar

INSTRUCTIONS for USE

INSTALLATION INSTRUCTIONS

T.B. 04/2005 MB

HiPro 3000

HiPro 4000

HiPro 6000

HiPro Vision

1.0 INTRODUCTION 3

2.0 FOR YOUR SAFETY 3

2.1 Warnings and Safety Advice 3

2.2 Coolant 3

3.0 WARRANTY AND 3

CUSTOMER SERVICE

4.0 INSTALLATION 4

4.1 The Purpose of this Manual 4

4.2 Tools/Materials Required 4

4.3 Unpacking 4

4.4 Cleaning 4

4.5 Installation 5

4.6 Securing 6

4.7 Connecting the Device to the 6

Electricity Supply

4.8 Changing the Sliding Hinge 8

4.9 Changing the Doorhang 9

4.10 Decor Panel 10

5.0 INSTRUCTION FOR USE 11

5.1 Initial Operation 11

5.2 Temperature Control 11

5.3 Automatic Defrost Function 11

5.4 Leakage Detection 11

5.5 Postioning the Storage Rack 12

5.6 Interior Light 12

5.7 Door-opening Control Device 12

5.8 Check List 13

5.9 Technical Data 14

5.10 Spare Parts 14

5.11 Environmental Advice 15

5.12 Disposal 15

5.13 Energy Saving Tips 15

5.14 Declaration of Conformity 15

TABLE OF CONTENTS

Model No.

Product No.

Serial No.

These operating instructions should be kept in a safe place.

If this device is passed on, please include these operating instructions with it.

Warning

Attention

Information

Environmental

Advice

INTRODUCTION

You have made an excellent choice by choosing the Dometic miniBar.

We are convinced that you will be satisfied with your new appliance in every way.

Silent in operation because of the Absorption principle, the miniBar fulfils high quality

standards and guarantees an efficient use of resources and energy during its entire

working life, i.e. during manufacturing, use and disposal.

Please study the installation and operating instructions carefully before

attempting to operate the miniBar.

FOR YOUR SAFETY

Warnings and Safety Advice

In the interests of children's safety:

When disposing of the refrigerator, remove all doors and leave the

shelves inside. This prevents children from being accidentally trapped or

suffocated in the refrigerator.

Never open the cooling unit - it is under high pressure.

Never store explosive substances, such as lighter fuel, petrol, ether or

similar products in the miniBar.

The minibar is not suitable for the proper storage of medications.

The miniBar must be installed in such a way that accidental contact with

the cooling unit (which heats up when in use) is impossible.

The appliance has to be connected to a properly earthed socket in line

with the relevant valid country regulations.

Servicing must only be carried out by authorised service personnel.

Coolant

Ammonia is used as a coolant.

This is a natural compound also used in household cleaning agents (1 litre of

Salmiak cleaner contains up to 200g of ammonia - about twice as much as is

used in the refrigerator). Sodium chromate is used for corrosion protection

(1,8% of the coolant).

If a leak occurs (which can be easily detected due to the unpleasant smell):

Switch the device off (pull mains plug, if applicable);

Ventilate room thoroughly.

Inform hotel personnel.

For the safety of hotel guests and personnel, it has been established by

inspectors that the coolant poses no threat to health.

WARRANTY AND CUSTOMER SERVICE

Warranty arrangements are in accordance with EC Directive 44/1999/CE and the

normal conditions applicable for the country concerned.

For warranty or other servicing, please contact our Dometic service department.

Any damage due to improper use is not covered by the warranty. The warranty

does not cover any modifications to the appliance or the use of non-original

Dometic parts; the warranty does not apply if the installation and operating

instructions are not adhered to and no liability shall be entertained. Parts can be

ordered throughout Europe from our Dometic service department.

When contacting customer service, please always state model, product number,

11..00

22..00

2.1

33..00

2.2

MLC-Code and serial number !

You can find this information on the model label inside the device.

INSTALLATION

The Purpose of this Manual

The manual shows you how to:

install the miniBar correctly.

operate the miniBar correctly.

guarantee the miniBar´s correct maintenance and functioning.

deal with faults by yourself.

Tools / Materials Required

You will need the following tools for initial operation:

Unpacking

Check during unpacking that the device is defect-free.

Report transport damage to the transport company within 48 hours.

Check that the voltage noted on the model label corresponds to the

mains voltage.

Depending on the model, the following parts can be found in the miniBar :

Cleaning

Before operating the miniBar, we recommend you clean it both inside and

outside.

Use a soft cloth, lukewarm water and a mild detergent.

Following this, wash out the miniBar using clean water and dry thoroughly.

At annual intervals, remove dust from fridge aggregate using a brush or

soft cloth.

AATTTTEENNTTIIOONN

To prevent material damage:

Do not use soap or detergents which are harsh, coarse or which contain

soda.

Keep the door seal free from oil and grease.

The cylinder locks have been lubricated in the factory to be long-lasting.

4.1

4.2

4.4

44..00

4.3

mild detergent

e.g. HHiiPPrroo 33000000

2x sliding hinge

Special

Equipment

IR-transmitter

Reflector

Installation4.5

1. The refrigerator must be level both directions.

2. There should be 20mm clearance to the wall.

3. Ventilation must be provided as shown in

alternatives A, B, C or D.

4. The ventilation duct must at least measure

105mm x the width of the refrigerator.

5. Only the entire cooling unit must project into

the duct as shown.

6 Air passing through the duct must not be

preheated by any source of heat.

7. Ventilation grills, if used, must have openings

of at least 200cm² each.

Please follow the installation details below

carefully. Guarantee is valid for products

installed as described only.

IMPORTANT:

200 cm²

20 mm

The mains plug/socket must be freely accessible once the

miniBar has been installed.

Securing

Connecting the Device to the Electricity Supply

The device must be connected to a properly earthed

socket in line with the relevant valid country

regulations.

The mains plug/socket must be freely accessible.

Check prior to initial operation that the voltage

noted on the model label corresponds to the

mains voltage.

If this is not the case, do not connect the

device and contact your dealer!

If the connection cable is damaged it must be replaced by the Customer

Service at Dometic, or by respectively qualified personnel, in order to pre-

vent any hazards.

4.6

4.7

Drive in the screws and place the caps

on.

When being built into a cupboard or

a recess, the miniBar must be posi-

tioned in such a manner that both

hinges/feet of the unit lie flush.

The miniBar is then (see Figures a,

b) screwed, at its hinges, to the

piece of furniture in question.

In the case of units with 8mm feet

and with LED option for the door

opening control, the reflector deli-

vered with the unit must also be

installed in the manner shown in

Figure a.

Stick on

supplied reflector., ...

Attention: For GB only !

Plug connection for United Kingdom only

If a 3-pin plug is used, it should be fitted with a 3 amp fuse,

with other plug types, the circuit should contain a 5 amp fuse.

Warning - This appliance must be earthed.

IMPORTANT

The wires in the mains lead of this appliance

are coloured in accordance with the following

code:

GREEN and YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead

may not correspond with the coloured markings

identifying the terminals in your plug, proceed as

follows.

1. Connect the GREEN and YELLOW coloured wire to the plug terminal

marked letter Eor earth symbol or coloured green or green and yellow.

2. Connect the BROWN coloured wire to the plug terminal marked letter L

or coloured red.

3. Connect the BLUE coloured wire to the plug terminal marked letter Nor

coloured black.

Moulded-On Plug Version

The mains lead is fitted with a non-rewirable moulded-on plug containing

a 3 amp fuse. If the fuse requires replacing at any time, the fuse

cover/carrier should be removed using a small screwdriver to level out. The

old fuse should be replaced by a 3 amp ASTA approved BS1362 fuse and

the fuse cover/carrier must be refitted before the plug is used again.

If the fuse cover-carrier is lost, a replaceement can be obtained from the

Dometic Service Shops.

The fuse cover/carrier must be of the same colour as that of the coloured

insert in the base of the plug. In no circumstances must the plug be used

without a correct fuse cover/carrier fitted.

If the plug supplied on the mains lead is not suitable for the socket in your

home, it should be cut off and disposed of safely, or destroyed, to avoid any

possible shock hazard resulting from the plug being inserted into a 13 amp

socket elswhere in the use. A suitable replacement plug should then be

fitted as given above.

4.7.1

Changing the Sliding Hinge4.8

1. 2.

3. 4.

Distance to cupboard door (A)

1. When closed, the cupboard door (A) must not lie against the rest of the

surrounding cupboard area (distance 1-2mm).

1. 2.

2. There must be a distance of 6-8mm between the cupboard door and the

miniBar.

Changing the Doorhang

4.9

Pull out LED, lay the cable

into the cable routing and

insert the LED at the oppo-

site side.

If the miniBar is equipped with the LED first carry out steps a. - e. :

LED

(optional) LED

door-opening con-

trol always opposite

the hanging side

d. + e.

device with feet

Pull the lower hinges forwards, pull out the door with the hinge.

Remove the upper hinge pin and insert on the other side, change the lower pin in the door.

Then push the door in together with the lower hinge.

Decor Panel

Measurements

Thickness 0,4 mm

Changing the decor panel

4.10

4.10.1

4.10.2

H x W (mm)

HiPro 3000 492 x 294,5

HiPro 4000 524 x 311,5

HiPro 6000 533 x 376,5

Hole for door lock (a)

diameter O 23,5 mm

distance from the edge (h) 62 mm

- Detach the lower door hinge and pull the door out (see also "4.9").

- Remove the holder for the lock (A) (mounted).

- Detach the lower frame section (B) (not screwed) and remove.

- Slightly bend the decorative panel (C) and pull it out of the door frame.

- Push in a new decorative panel with the upper edge running exactly

parallel to the upper part of the frame.

- Place the frame section (B) on and press firmly (clip in)

- Place the door onto the lower hinge, insert the hinge pin into the top of the

door, push the door with the hinge into the hinge receptacle at the bottom

and allow the hinge to notch. Insert the hinge pin in the door, push in

the door and let the hinge click in.

Remark (devices without doorlock):

- Additional installation of a door lock is possible (available from Dometic)

- In the door the position for the opening is prepared.

- Drill the hole in accordance to the drawing above.

Andere Handbücher für HiPro 3000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic miniBar RH 465LD Bedienungsanleitung

Dometic

Dometic A30S1 Bedienungsanleitung

Dometic

Dometic RM 123E Bedienungsanleitung

Dometic

Dometic DW6 Bedienungsanleitung

Dometic

Dometic HIPRO A30 Bedienungsanleitung

Dometic

Dometic RM1350 Elite Bedienungsanleitung

Dometic

Dometic DS 200 Bedienungsanleitung

Dometic

Dometic MF20-60 Bedienungsanleitung

Dometic

Dometic AMERICANA RM2652 Handbuch

Dometic

Dometic 8 Series Bedienungsanleitung

Dometic

Dometic Frigo DC Bedienungsanleitung

Dometic

Dometic DM50D Bedienungsanleitung

Dometic

Dometic RM 4601 Bedienungsanleitung

Dometic

Dometic RML9336 Bedienungsanleitung

Dometic

Dometic RM 3762 Bedienungsanleitung

Dometic

Dometic RM 4223 Bedienungsanleitung

Dometic

Dometic NDR 1402 Bedienungsanleitung

Dometic

Dometic RM 5310 Bedienungsanleitung

Dometic

Dometic FRIGO DC Series Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic NRX Series Bedienungsanleitung

Dometic

Dometic 5 Series Bedienungsanleitung

Dometic

Dometic NDA1402 Bedienungsanleitung

Dometic

Dometic DESIGN DM50C D Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung