Dometic Type: JCB-1 Bedienungsanleitung

207.5013.03 0402

Type: JCB - 1

Gebrauchsanweisung

Mode demploi

Instruzioni per luso

Operating instructions

Gebruiksaanwijzing

Instrucciones de manejo

DE AT CH LU

BE CH

IT CH

Dear customer,

please read the instruction book and all additional information

before using the appliance. It is most important that they should be

retained with the appliance for future reference!

1. Warnings and directions

These warnings are provided in the interest of safety. You must read them

carefully before installing or using the appliance

This product is designed to be operated by adults. Children should not

be allowed to tamper with the controls or play with the product.

Any electrical work required to install this appliance should be carried

out by a qualified electrician.

It is dangerous to alter the specifications or modify this product in any

way.

The absorption refrigerator is designed to be used specifically for the

storage of edible foodstuffs and drinks only.

There are working parts in this product which heat up. Always ensure

that there is adequate ventilation as a failure to do this will result in

component failure and possible food loss (refer to relevant instructions

for unit installation under point 4.).

Before defrosting, cleaning or maintenance work is carried out, be sure

to switch off the appliance and unplug it. Shut down gas operation

Manufacturers' food storage recommendations should be strictly

adhered to. Refer to relevant instructions for food and drink storage

under point 13.

Under no circumstances should you attempt to repair the appliance

yourself. Repairs carried out by inexperienced persons may cause injury

or more serious malfunctioning. This product should be serviced by an

authorised Service Engineer, and only genuine spare parts should be

used.

2. Area of use

The cooling unit must not be installed in motor vehicles and boats when

using the gas operation method

Operation using liquid gas in enclosed spaces in not permitted

THIS COOLING NIT MAY ONLY BE SED WITH GAS O T OF DOORS!

Outdoor use includes tents (awnings) which are well ventilated throughout

unit operation and flat garden terraces.

There are no restrictions on electrical operation.

Site of operation must be protected from rain and other water sources.

3. Storage of gas cylinders

Liquid gas cylinders should never be stored in unventilated areas or below

ground (funnel-shaped holes). Avoid direct sunlight. The gas cylinder should

not be exposed to temperatures in excess of 50°C.

4. Installation

To be installed horizontally on a smooth, firm or any other appropriate

surface. If necessary, adjust/align using a spirit level or a water-filled vessel.

There should be a distance of at least 10cm between the back of the unit

and any other object (wall).

Avoid placing unit in direct sunlight and next to other sources of heat.

For good air circulation the air vents on the top and under sides, as well as

at the back of the cooling unit must not be obstructed.

This will result in a good, energy-saving cooling system.

5. Cleaning

Prior to initial use and later after defrosting, or prior to a prolonged period

out of operation, clean the container and lid with luke-warm water and, if

necessary, washing-up liquid. Warning: do not inadvertently press or

force the opened door past its stop-point (this could cause the hinges

to break). Never use scouring or corrosive agents to clean the unit.

Wipe cleaned surfaces dry with a soft cloth.

6. A/C operation

Do not use any additional form of energy (batteries/gas).

Check that the supply voltage corresponds with the line-voltage data on the

type-plate (see back of unit).

(The following instructions refer in the main to coolers manufactured for the

United Kingdom).

The mains lead of your refrigerator is fitted with a non-rewirable moulded-on

13 amp plug containing a 3 amp fuse. It is a regular earthed plug for

connection to a regular earthed socket.

Due to the difference in the plugs used, an adapter will be necessary for

other countries.

If the fuse requires replacing at any time, the fuse cover/carrier should be

removed using a small screwdriver to lever it out. The old fuse should be

replaced by a 3 amp ASTA approved BS 1362 fuse and the fuse

cover/carrier must be refitted before the plug is used again.

If the fuse cover/carrier is lost, a replacement can be obtained from the

service shops. The fuse cover/carrier must be of the same colour as that of

the coloured insert in the base of the plug. In no circumstances must the

plug be used without a correct fuse cover/carrier fitted.

If the plug supplied on the mains lead is not suitable for the socket in your

home, it should be cut off and disposed of safely, or destroyed, to avoid any

possible shock hazard resulting from the plug being inserted into a 13 amp

socket elsewhere in the house. A suitable replacement plug should then be

fitted as given below.

General guide to fitting any plug

Ensure the lengths of wire inside the plug are prepared correctly.

Connections should be firmly made after all conductor strands are entered

into the terminal posts. When preparing the cable ends take care not to

damage the outer sheath, or the insulation surrounding the inner conductors.

Tighten all screws. Replace the top cover of the plug and secure.

Other versions

Your refrigerator has a 3-wire mains lead which is intended for connection

to a 3-pin plug and a properly earthed socket outlet.

IMPORTANT: The wires in the mains lead of this appliance are coloured

in accordance with the following code:

GREEN-AND-YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE

As the colours of the wires in the mains lead may not correspond with the

coloured markings identifiying the terminals in your plug, proceed as follows:

the wire which is coloured GREEN-

AND-YELLOW must be connected to the

terminal in the plug which is marked with the

letter E or by the earth symbol or coloured

green or green-and-yellow. The wire which is

coloured BLUE must be connected to the

terminal which is marked with the letter N or

coloured black. The wire which is coloured

BROWN must be connected to the terminal

which is marked with the letter L or coloured

red.

WARNING - THIS APPLIANCE M ST BE EARTHED!

If a 13 amps (B.S. 1363) fused-plug is used, it should be fitted with a 3 amp

fuse. In other cases, the circuit to which the refrigerator is connected should

be fitted with a 5 amp fuse.

To turn on (Fig. 1)

Turn thermostat knob (A) clockwise to position 7/MAX. Only after

approximately 1 hour will the unit become noticably cool (frost on

evaporator).

The temperature can be regulated using the thermostat knob: '0'=off, 1-

7 increasing degrees of coolness.

After sufficient cooling (approximately 5 hours), the thermostat position

can be set to a lower temperature, between 2-5. The thermostat will now

automatically regulate the set temperature.

To turn off (Fig. 1)

Turn thermostat knob (A) anticlockwise to position '0' (a slight resistance

will be felt just before this position).

Pull out mains plug.

7. D/C operation

Do not use any additional form of energy (mains/gas). A safety fuse must be

installed in the electricity supply between battery and refrigerator in a duct.

12 V: maximum 15 amps; 24 V: maximum 7.5 amps.

It is not necessary to consider the polarity when connecting the unit. Check

that the battery voltage corresponds with the line-voltage data on the

cooling unit type-plate. If no battery is used independently of the vehicle, the

cooling unit is only to be used when the vehicle is in motion, since, when the

engine is not running, the battery can discharge to such an extent that the

engine will not restart.

Recommendation: Before a journey, pre-cool the unit using the supply

voltage.

max. cable lengths

Cable cross section 12 V 24 V

2.5 mm2until 2.5 m 5 m

4.0 mm2until 4.0 m 8 m

6.0 mm2until 6.0 m 12 m

To turn on

The car plug fitted to the connecting cable is to be plugged into the

socket/cigar lighter (car plugs are not supplied with every model).

When using battery operation, the cooling performance is not

thermostatically regulated, i.e. knob (A) is ineffective.

When knob (A) is ineffective or if the temperature is unnecessarily too low:

Turn off unit

Pull out plug from socket.

8. Liquid gas operation

Do not use any additional form of energy (mains/battery). The unit must not

be connected to town or natural gas pipelines. It is only suitable for use with

propane/butane gas (e.g. Calor Gas, Camping Gaz, Caravangas, etc).

The specified gas-connection pressure is given in mbar on the type plate

(see back of appliance). It is important that a non adjustable pressure-

regulator is used to reduce the pressure in the gas cylinder to the operating

pressure specified on the rating-plate, no other pressure may be used.

Needle valve operated gas control taps are NOT suitable for use with

this appliance and must not be used as a substitute for a pressure

regulator.

9. Connecting the cooling unit to the gas

cylinder

(The following instructions refer in the main to coolers manufactured for the

United Kingdom. For other countries please refer to your supplier).

Always connect in the following sequence:

GAS BOTTLE →→PRESS RE-REG LATOR →→APPLIANCE.

To connect the appliance to the pressure-regulator SUREFLEX

ARMOURED FLEXIBLE PIPE should be used. This can be ordered through

CALOR GAS dealers, caravan accessory shops, or direct from the

manufacturer, The Lunken Co. Ltd.

When ordering the Sureflex Pipe, it must be specified which type of

connector is required at each end:

a) if the pressure-regulator outlet has a 3/8" B.S.P. female thread, the pipe

must have a 3/8" B.S.P. male thread at one end;

b) if the pressure-regulator has a ridged nozzle outlet instead of a thread,

the pipe must have a special connector at one end.

To connect this to the pressure-regulator, first unscrew the nut (3) and place

it tgether with the sleeve (2) onto the nozzle of the regulator. The shouldered

end of the sleeve should face away from the regulator Remove the rubber

'0'ring (1) and push it over the end of the nozzle so that it locates in the first

corrugation. Push the threaded end ot the Sureflex Pipe against the end of

the nozzle, then screw up the nut, tightening the assembly with spanners to

make a gas-tight joint.

In both of the above instances, the other end of the Sureflex Pipe should

terminate in a 1/4" o.d. extension piece. In order to connect this to a 1/8"

B.S.P. female threaded gas inlet of the appliance a coupling which has a

1/8" B.S.P. male thread at one end and a nut and 1/4" olive connection at

the other end to suit the 1/4" o.d. extension piece (such as manufactured by

Wade Couplings Ltd. under their part number 4063/1 is needed.

When fitting the connection to the gas inlet of the appliance by applying a

fork-spanner, hold counterpart to avoid straining and possibly damaging.

The gas bottle must only be used in an upright position and particular care

must be taken every time the appliance is connected to the gas bottle to

ensure that there are no leaks, that the gas pipe (rubber hose) is not under

tension or kinked, and that it is not in contact with hot surfaces.

The connection pipe and gas bottle should always be located in positions

where they will not be tripped over or otherwise inadvertently disturbed.

Before attempting to light the burner, every time after connection, turn on the

gas at the bottle and check the gas connections for leaks by applying a soap

and water solution over them and watching for bubbles, which would

indicate a leak.

For your safety

Do not check for leaks with a naked flame

Do not smoke while checking for leaks

10. Gas equipment system (Fig. 1)

This consists of a control knob (B) with built-in safety pilot, a burner with

igniter plug and a piezo-gas igniter (E).

The control knob has 3 positions:

MAX : high cooling capacity,

MIN : low cooling capacity,

: off-position = gas supply to burner is shut off.

Remark: cooling boxes for the United Kingdom are fitted with a multiple

regulator-unit which has only two positions: MAX an MIN. There is no

position CLOSED.

If, for any reason the gas flame extinguishes the ignition control is working

automatically and shuts off gas supply.

11. Igniting the gas burner (Fig. 1)

1. Open gas cylinder or pressure regulating valve.

2. Turn knob (B) anti-clockwise to the MAX position, press and hold down.

3. After approximately 10 seconds press knob (E) several times. After

ignition, hold down knob (B) for a further 20-30 seconds before

releasing.

The flame can be controlled by aperture (C).

Should no ignition occur, repeat the ignition process after 1 minute.

(This could take longer than 10 seconds if the unit has been out of

operation for a prolonged period or after replacing the gas cylinder.

Cause: air in the lines).

4. Once sufficient refrigeration has been obtained in the cooling tank at the

MAX position, the control knob should be turned to the MIN position by

low outside temperatures or when the refrigerator is only lightly loaded

respectively the ambient temperature is below +18°C, in order to avoid

overfreezing the contents.

12. Shutting down gas operation

1. Close gas cylinder or pressure regulating valve.

2. Turn knob (B) clockwise to the off position*.

*excluding units for the United Kingdom.

13. Food and drink storage

Foodstuffs and drinks should always be sealed when stored in the

cooling unit. Thus, changes in taste and smell are avoided.

Food and drink should be so placed in the cooler so as to allow air to

circulate freely.

Do not place hot food or drinks in the cooler

Under no circumstances should inflammable liquids and/or gases be

stored in the cooler. Explosion hazard

14. Defrosting and measures for prolonged

periods of disuse

A build up of too much ice on the evaporator hinders cooling of the unit and

thus reduces effectiveness. When there is an approximately 5-mm-thick

layer of ice build-up it is recommended to defrost the cooling unit. Thus, the

cooling unit will be turned off and any goods to be cooled removed. Never

use heated appliances, heaters, etc. to speed up the defrosting process If

necessary, a cloth dipped in warm water can be placed on the unit to help

the defrosting process. After defrosting, clean up the defrosted water with a

clean cloth and clean the cooler containers as described in chapter 4.

Should the unit be out of operation for a prolonged period, turn off unit and

remove contents. After defrosting, the cooler should be cleaned carefully

and dried.

To avoid the build-up of any unpleasant smells in the cooler, it is

recommended to leave the lid slightly open.

15. Measures after prolonged periods of disuse

Should the cooling unit not function correctly when switched on after being

out of operation for a prolonged period, SHUT OFF THE POWER SUPPLY

AND DISCONNECT then turn the appliance upside down.

After a few minutes return the appliance to its upright position and switch on

again. Should the unit still not fuction correctly, repeat the process several

times.

16. Maintenance

Changing the gas filter: the cellulose gas filter is situated at the back in the

gas connection piece. When it becomes necessary to replace the gas filter,

remove the filter from the duct and replace it with a new one. Any other

maintenance and repair works, especially those relating to the cooling

aggregate and the gas-burner system, may only be undertaken by

authorized customer service points.

17. After-sales service

Should a problem arise with the unit, please check the following before

contacting customer service:

is the unit suitably placed and is it well ventilated?

is the unit placed on a flat surface?

does the socket supply current?

is the connecting cable damaged in any way?

is there a loose connection?

has the plug been properly plugged into the socket?

has the electrothermostat been correctly adjusted?

in the case of gas operation, has the safety pilot knob (regulator) been

pressed down long enough?

has the regulating knob been turned to the correct position?

is the gas cylinder or pressure regulating valve open?

does the liquid gas cylinder still contain gas? If no liquid movement is

evident on shaking the cylinder, then the gas cylinder is empty.

are several operating methods being used simultaneously?

have warm foodstuffs been stored in the cooler?

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic TCW 3000 SDD Montage- und Bedienungsanleitung

Dometic

Dometic CRD0050 Bedienungsanleitung

Dometic

Dometic GM CCF-T Bedienungsanleitung

Dometic

Dometic RC Series Bedienungsanleitung

Dometic

Dometic RH430STE Bedienungsanleitung

Dometic

Dometic RM 4605 and Handbuch

Dometic

Dometic 5 Series Bedienungsanleitung

Dometic

Dometic Coca-Cola Cool Can 10 AC/DC Bedienungsanleitung

Dometic

Dometic RM 7271 L Bedienungsanleitung

Dometic

Dometic CDF2 Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic NRX Series Bedienungsanleitung

Dometic

Dometic RMD 8501 Bedienungsanleitung

Dometic

Dometic CDF-11 Bedienungsanleitung

Dometic

Dometic RMDT 8501 Bedienungsanleitung

Dometic

Dometic RMS 8465 Bedienungsanleitung

Dometic

Dometic SUPERCOOLER RC 4000 Bedienungsanleitung

Dometic

Dometic RML933 Series Bedienungsanleitung

Dometic

Dometic RMT 7650 Bedienungsanleitung

Dometic

Dometic RCCA 920 Bedienungsanleitung

Dometic

Dometic RGE Series Bedienungsanleitung

Dometic

Dometic 5 Series Bedienungsanleitung

Dometic

Dometic RGE Series Bedienungsanleitung

Dometic

Dometic CF SERIES Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung