Dowtel DTT-800 Bedienungsanleitung

CONTENTS

About Dowtel FWT

1Before using

1.1 Checking accessories

1.2 Physical Description

1.3 Sound & Tone

1.4Precautions

2Installations

2.1 General installation

2.2 Installation to use Data Service

3Basic Functions

3.1 Turing on the power

3.2 Turning off the power

3.3 Making a call

3.4Answering a incoming call

3.5 Using the Analog G3 Fax

3.5.1 Transmitting a document by fax

3.5.2Receiving a document by fax

3.6 Data Service

3.6.1 Setting Data service receiving mode

4 Supplementary Functions

4.1 Call Functions

4.1.1 Speed Dial

4.1.2 Emergency Call Hold

4.1.3 Hot Line

4.2 Phone Book

4.2.1 Storing phone numbers

4.2.2 Deleting phone numbers

4.3 Additional

4.3.1 Alarm Reminder

4.3.2 Ear-piece Volume Control

4.3.3 Voice Privacy

4.4 Lock

4.4.1 Outgoing Lock

4.4.2 Changing Lock code

DTT-800/1900 Operating Manual

4.4.3 Reset as Default

4.5. Maintenance Setup

4.5.1 CLIP setting

4.5.2 Analog G3 Fax standard setting

4.5.3 Default Data rate setting

4.5.4 Ringer Frequency & Cadence Control

4.5.5 Dial Tone Frequency Control

4.5.6 Default Vocoder Selection

4.5.7 Timed Hot Line Dial send waiting time control

4.5.8 Hook-Flash detecting time setting

4.5.9 Serial Baudrate

4.5.10 Network Dial Tone setting

4.6 System Parameter Setup

4.6.1 Phone Number(MIN) Input

4.6.2 A-key Input

APPENDIX

1. Summary table for supplementary function

2. Technical Specification

3. Troubleshooting

4. Feature Code Table

DTT-800/1900 Operating Manual

About Dowtel FWT

(1) This is simple and elegant design and is devised very suitable for the office and the house.

(2) Its basic purpose is for the use at the desk, but you can install this at any place thanks to the Wall-

mount kit.

(3) This provides clear and noiseless voice quality. (QCELP, EVRC)

(4) A user can control the volume of a handset at one’s choice.

(5) A built-in battery secures the phone use even in the blackout.

(6) Three tricolor LEDs visually indicate the status of the terminal.

(7) A user can control the terminal use of the other part with the Outgoing Lock function.

(8) A user can simply transmit the number stored in a phone book by using One-Touch and Two-Touch

Dial.

(9) Emergency Call Hold function enables a user to notify the emergency situation to the other part.

(10)The most frequently used number is automatically connected even when a user picks up a handset,

thanks to the Hotline Call function.

(11)In case of Battery discharge, wrong operation or Air Link cut-off, this provides various alert functions

(by sound & LED)

(12)The connection of this terminal with the system supplies DTMF transmission for ARS connection.

(13)The connection with the system supports a variety of additional functions such as the three-way

calling, call waiting , call transfer and call forwarding.

(14)Connected with PC, the packet, circuit and PC fax communication become possible.

(15)By the Voice Privacy function, the illegal tapping can be prevented.

(16)This terminal has an authentication function preventing a user’s phone number from being used

illegally by others.

(17)Calling Line Identification is supported.

(18)As this is designed with the convenient menu to use, a user can set the terminal function easily and

simply.

(19)Analog G3 Fax (Optional) service is supported.

(20) To support the Pay Phone Interface, this transmits 16KHz, 12KHz, Metering Pulse, Polarity

Reversal signal. (Optional)

DTT-800/1900 Operating Manual

1. Before Using

This manual consists of the terminal introduction, the installation method, the basic directions,

feature code and the technical standard, describing ways to resolve some possible problems in

using. Please carefully read through contents of this manual before using this product.

[Note]

When you have any questions or think that you got any product defect in using FWT terminal,

please contact a place you bought.

1.1 Accessories check

FWT terminal provides following accessories. After purchasing, you are required to open up the

box and check out if accessories inside consist of all as below.

FWT terminal Antenna TEL LINE

SMPS User’s Manual Screws

DTT-800/1900 Operating Manual

1.2 Name and function of each part

lPOWER LED

LED lights on in red when the external power is supplied.

lBATTERY LED

Indicates the status of backup battery.

The terminal can be operated if the backup battery is connected, even though the external power

supply is stopped.

Please refer to following table for the LED operation.

-From the moment that battery LED blinks, a phone call is possible for about 10 minutes.

Battery Power (V) Battery Level Battery LED Power LED Terminal

Status

6.6 ~ 5Green Off Normal

6.1 ~ 6.5 4Green Off Normal

5.8 ~ 6.0 3Orange Off Normal

5.6 ~ 5.7 2Orange & Blink Off Normal

Warning Tone

~ 5.5 1Off Off Power off

External power

supply Off Red Normal

SERIAL PORT ANTENNA

RJ-11 JACK DC JACK POWER SWITCH

SERVICE LED BATTERY LED POWER LED

DTT-800/1900 Operating Manual

lSERVICE LED

Indicates call service availability.

Power intensity (dBm)

RSSI Level LED status Terminal status

~ -85 5Green Service available

-86 ~ -91 4““

-92 ~ -97 3““

-98 ~ -103 2““

-104 ~ -110 1Green & Blink “

-111 ~ 0Red No Service

During a call Orange Indicates during a

call

LED Red : Indicates the call service is not available as the receiving power intensity is weak.

LED Green & Blink : Indicates the call service is available although the receiving power intensity is weak.

LED Green : Indicates the receiving power intensity is strong and the call service is available.

LED Orange : Indicates the call service is now on, regardless of the receiving power intensity.

[Notice] Malfunction Indicator

In case of the terminal malfunction, Service LED and Battery LED light in red and blink at the same

time.

Please contact the service provider for this matter.

lDC JACK

Through This part, the SMPS supplies the FWT terminal with the power.

-AC Input voltage of SMPS ranges 100 ~ 240 V.

lPOWER SWITCH

The power of FWT terminal consists of the external and the internal power.

Although DC Jack at the terminal backside gets unplugged, the terminal does operate until the

built-in battery discharges. If a user does not use the terminal for long or wants to turn off the

power, please switch off the power.

lSERIAL PORT

A port used to connect to the PC for the maintenance/repair and the data communication.

lRJ-11 JACK

Connects the general phone or a fax.

-This terminal is basically provided with 2 jacks.

-You can connect 2 phones at the same time but there is no mutual security function.

-You can connect up to 5 phones to RJ-11 jack.

(A user must buy additional parts to extend the connection)

DTT-800/1900 Operating Manual

1.3 Sound & Tone

1.3.1 Power-up Sound

The sound sent to the buzzer when the terminal starts booting.

1.3.2 Dial Tone

Indicates that the call is available.

1.3.3 Warning Tone

The sound transmitted to the handset in below cases.

-In case the call is not available due to the broken air link of terminal.

-In case the dialing is late after picking up a handset

-In case the terminal is in the wrong operation.

1.3.4 Howler Tone

In case the handset is not put in place after the end of a warning tone, it alarms through a buzzer

for 30 seconds.

1.3.5 Keypad Tone

The sound transmitted to the handset when the keypad is pushed,

1.3.6 Ring Sound

The sound transmitted to the buzzer indicating the receipt of a call after a handset is picked up.

1.3.7 Low Battery Warning Tone

In a situation that the terminal operates with the built-in battery, this is the sound transmitted to the

buzzer indicating the falling of remaining current below the specific value.

1.3.8 SMS/VMS notification tone

The sound transmitted to the buzzer to notify the receipt of SMS or VMS message.

1.3.9 Error Tone

The sound to indicate the keypad operation that isinconsistent to the present terminal status.

But, the keypad operation that was already input is ignored.

DTT-800/1900 Operating Manual

1.4 Notes for using

lFWT terminal was designed as the durable equipment to ensure the operational reliability

in the normal environment and went through the test. However, you are requested to use in

a careful way.

A user is able to use for a long time by abiding by the following notes and handling the FWT

terminal right in a proper environment

1) Do not disassemble or alter the FWT terminal on your own.

(Please inquire a place you bought about the disassembling and the repair)

2) Do not touch antenna or let any parts of body touched during the call.

3) Do not use at hot and humid places. Be careful not to moisten the FWT terminal or to spill

any liquid on it. It may cause irreparable damage.

4) Avoid the vibration and impact and keep the FWT terminal at a safe place to avoid damage

while you are not using.

5) Do not use the FWT terminal near to explosives or in places where combustible liquids are

used.

6) Do not wipe the FWT terminal with a chemical solution like solvent or thinner.

(Wipe the outside with the soft cloth soaked with non-alkali detergent)

7) Switch off the FWT terminal and unplug the SMPS (Switch Mode Power Supply) when you

do not use for long.

DTT-800/1900 Operating Manual

2. Installations

2.1 General installation

lBefore installing the FWT terminal, check accessories in the package and start installing in

order as explained below.

1) As shown in the figure below, plug in the antenna in the arrow direction and turn it to clockwise

for the connection with FWT terminal.

2) Connect a general phone to RJ-11 Jack as shown in the figure below. There are 2 RJ-11 Jacks

in the terminal and you can connectany of them to use.

DTT-800/1900 Operating Manual

3) Connect SMPS exclusively used for the FWT terminal to DJ-JACK positioned at the left of

terminal. At this time, properly insert the power jack until it is not inserted any further.

4) Connect the power plug of SMPS to the outlet.

5) Switch on the power and the next operation is done as follows.

lAfter all 3 lamps(LED) light on, only a power lamp that is now on the use lights.

lAfter a power-up beep sound through the terminal, a service lamp lights on to indicate the call

available.

[Notes] Malfunction Indicator

In case of a malfunction, a service LED and a battery LED light in red and blink at the same time.

Inquire a service provider for this.

Andere Handbücher für DTT-800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dowtel Touch-Terminal Handbücher

Dowtel

Dowtel WS-2100 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung