Dräger Evita V Series Bedienungsanleitung

D-5759-2018

Disassembly/Assembly Flow Sensor

Open the ap by lifting the lower

edge upwards.

Close the ap.

Push the ow sensor as far as it

possible go to the left.

Push the ow sensor to

the right into the socket.

Remove the expiratory valve

from the tting.

Turn the locking ring as far as

possible to the left.

Remove and empty the water

trap container.

Connect the water trap container.

Remove the diaphragm.

Fit the ow sensor

into the socket.

Remove the ow sensor

from the socket.

Remove the sensor sleeve

from the expiratory valve.

Attach the diaphragm onto the

edge of the expiratory valve housing.

Make sure that it tts properly.

Attach the ow sensor sleeve

on the expiratory valve.

Turn the locking ring as far

as possible to the right

until it clicks into place.

Turn the locking ring as far as

possible to the left, push the

expiratory valve into the tting.

Dräger Evita®V-Series

Flow Sensor and Expiratory Valve

Disassembly/Assembly

Disassembly/Assembly Expiratory Valve*

* The Neonatal Expiratory Valve is

also working with Evita® V-Series.

For manual reprocessing of the

Neonatal Expiratory Valve please

refer to Babylog guideline.

This guideline does not replace or amend the instructions for use. Please always refer to the

reprocessing instruction in the latest instruction for use of the components. The instructions

for use and the hospital guidelines and policies always have to be observed.

D-5759-2018

Prepare the cleaning and the disinfectant solution in

accordance with manufacturer’s instructions.

Dräger Evita®V-Series

Flow Sensor

Reprocessing instructions

Manual cleaning

This guideline does not replace or amend the instructions for use. Please always refer to the

reprocessing instruction in the latest instruction for use of the components. The instructions

for use and the hospital guidelines and policies always have to be observed.

Swirl the ow sensor back and forth at least 3 times.

Make sure the cleaning agent reaches all surfaces

and interior spaces.

Place the ow sensor in the cleaning agent. Ensure that the cleaning solution ushes all surfaces

and interior spaces. At the end of the specied

contact time, swirl the ow sensor back and forth

again at least 3 times.

After the contact time, rinse the ow sensor in the

water bath (at least drinking water quality). Shake out residual water carefully.

Check the ow sensor for visible soiling and repeat

steps if necessary.

Check the ow sensor for visible damage, paying particular attention to its measuring wires and their pins,

and replace if necessary.

Allow the ow sensor to dry completely.

Do this until no more cleaning agent residue is visible.

D-5759-2018

Dräger Evita®V-Series

Disinfection

Machine cleaning

This guideline does not replace or amend the instructions for use. Please always refer to the

reprocessing instruction in the latest instruction for use of the components. The instructions

for use and the hospital guidelines and policies always have to be observed.

Manufacturer:

Drägerwerk AG & Co. KGaA

Moislinger Allee 53–55

23558 Lübeck, Germany

Disinfection by immersion

Place the ow sensor in the disinfectant. Observe the specied contact time.

At the beginning of the contact time, swirl the ow sensor back and forth at least

3 times. Make sure the disinfectant reaches all surfaces and interiors.

At the end of the contact time, swirl the ow sensor back and forth again at least

3 times.

After the contact time, rinse the ow sensor in the water bath (at least drinking

water quality) until no more disinfectant residue can be detected.

Shake out residual water carefully. Allow the ow sensor to dry completely.

Check the ow sensor for visible damage, paying particular attention to its

measuring wires and their pins, and replace if necessary.

If you need visual descriptions, please look at the reprocessing instructions for manual cleaning.

Position the expiratory valve as shown. Position the components (ow sensor sleeve, diaphragm, water trap container)

to be stable.

Please ensure that all surfaces and interior spaces can be completely rinsed and the water can drain o freely.

Machine cleaning

Andere Handbücher für Evita V Series

Andere Dräger Steuereinheit Handbücher

Dräger

Dräger RailGard-S1 Bedienungsanleitung

Dräger

Dräger VarioGard Bedienungsanleitung

Dräger

Dräger REGARD 2400 Bedienungsanleitung

Dräger

Dräger PAS ASV Bedienungsanleitung

Dräger

Dräger PAS ASV Bedienungsanleitung

Dräger

Dräger Regis 300 Bedienungsanleitung

Dräger

Dräger RAB 7000 Bedienungsanleitung

Dräger

Dräger REGARD 4208797 Montage- und Bedienungsanleitung

Dräger

Dräger PEX 1000 Bedienungsanleitung

Dräger

Dräger REGARD 7000 Bedienungsanleitung

Dräger

Dräger Area Bedienungsanleitung

Dräger

Dräger REGARD 3900 Series Bedienungsanleitung

Dräger

Dräger BS8468-1 Bedienungsanleitung

Dräger

Dräger Plus Series Bedienungsanleitung

Dräger

Dräger Scio Four Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung