Dremel DigiLab 3D45 Gebrauchs- und Pflegehandbuch

Having th corr ct nozzl gap is vital to achi ving succ ssful prints. Th nozzl gap, also r f rr d to as Z-Gap, is

th distanc of th nozzl to th build platform wh n th first lay r is b ing print d. It is important to nsur that

th first lay r sticks w ll to th build platform, th r for , th nozzl gap n ds to b id al. Too larg of a nozzl

gap may l ad to a not w ll adh r d first lay r, l ading to obj ct shifting, and a too small nozzl gap may l ad to a

non-visibl first lay r, possibly l ading to clogging issu s.

3D45 Nozzle Gap Calibration

SERVICE INSTRUCTIONS

Step 1: Go to Calibrate screen

From print r hom scr n, navigat to tools, calibrat ,

and th n assist d nozzl calibration. Advanc d us rs

can us th nozzl gap calibration dir ctly (non-assist d

mod ).

Advanc d us rs can mov to St p 4.

Step 2: Open Assisted Nozzle

Calibration screen

a. Apply glu on th build platform. S glu application

bull tin.

b. Ensur l v ling switch is fr of glu r sidu and that

th filam nt has b n load d.

c. L v l th build platform if n d d.

Step 3: Assisted Nozzle Calibration

a. Nozzl will start h ating up in ord r to p rform th

calibration.

b. In this proc ss, thr small r ctangl s will b print d

sid by sid . R ctangl A will b print d with an off-

s t of +0.1mm from th curr nt s tting, R ctangl B

will b print d with no offs t, and R ctangl C will

b print d with a -0.1mm offs t. An additional

r ctangl will b print d nclosing R ctangl s A, B,

and Cin ord r to prim th nozzl and mak sur fil-

am nt is flowing corr ctly b for starting th print.

Step 4: Nozzle Gap Calibration Analysis

a. Onc th print has b n compl t d, th r will b

thr diff r nt r ctangl s r pr s nting thr

diff r nt Nozzl Gap offs ts.

TOOLS ASSISTED NOZZLE

CALIBRATION

CALIBRATE

A B C

Please click here for Video Tutorial

b. Look at r ctangl s A, B, and Cto d t rmin which offs t has th b st lay r adh sion. Follow th instructions

b low for ach sc nario.

• If yo see little or no filament: If th nozzl is too clos to th build platform, th first lay r will print too

tight to th build plat . Incr as th Nozzl Gap +0.1mm. R p at th Assist d Nozzl Calibration Proc ss

until an optimum nozzl gap has b n achi v d.

• If the first layer is not adhering or gaps between the lines: If th nozzl is too far from th build plat , th

first lay r will not adh r w ll. D cr as th Nozzl Gap -0.1mm. R p at th Assist d Nozzl Calibration

Proc ss until an optimum nozzl gap has b n achi v d.

• Ideal nozzle gap distance: First lay r will b adh ring and b visibl . Lin s should not look lik th y w r

pr ss d against th build platform.

Congratulations!

You are now ready to build. Build On.

Andere Handbücher für DigiLab 3D45

Andere Dremel 3D-Drucker Handbücher

Dremel

Dremel 3D40 FLEX Montageanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Bedienungsanleitung

Dremel

Dremel DigiLab 3D40 FLEX Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Betriebsanleitung

Dremel

Dremel DigiLab 3D45 Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Bedienungsanleitung

Dremel

Dremel 3D40 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D40 Idea Builder Betriebsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Bedienungsanleitung

Dremel

Dremel DigiLab 3D45 Montageanleitung

Dremel

Dremel Idea Builder 3D20-01 Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D40-EDU Montageanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Dremel

Dremel Idea Builder 3D20-01 Montageanleitung

Dremel

Dremel 3D40 Idea Builder Bedienungsanleitung

Dremel

Dremel 3D20 Idea Builder Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch