Drive Inspired Kanga Bedienungsanleitung

REV2.10.4.17

www.inspiredbydrive.com

Kanga Wheelchair

Seating Package

Headrest

Truck Support

Thigh Supports

Abductor

Poly Tray

Drive DeVilbiss Healthcare

99 Seaview Boulevard

Port Washington N.Y. 11050 USA

Made in USA

step one - seat/back assembly

kanga seating package

Warning! Do not install this equipment without first

reading and understanding the instructions and parts

included with this package. Innovative concepts will not

be responsible for damage or injury as a result of misuse

or improper installation. We recommend an experienced

professional be consulted in the selection and application

process of this product.

Warning! Until all mounting clamps, brackets and parts

are properly tightened and securely attached, make sure

client is safely supported while positioning adjustments

are made to prevent the client from falling out of the

wheelchair.

NOTE - Seat/back assembly; “holes through upholstery”

have already been made for ease of assembly. Do not ini-

tially over tighten mounting hardware as final adjustments

will be necessary prior to fitting client into seating.

1.1 For shipping purposes only; the seat-to-back hinge is

attached to the back with only one bolt, loosen bolt and

adjust so that second bolt/washer can be installed to

securely fasten in place.

1.2 Align the seat and seat-to-back hinge to attach the

remaining two bolts/washers to bottom of seat.

1.3 Align the seat and seat-to-back hinge to attach the

remaining two bolts/washers to bottom of seat.

1.4 Align the seat and seat-to-back hinge to attach the

remaining two bolts/washers to bottom of seat.

Item Number

1300-921110

Kanga Seating Package 10” w/mounting hardware

1300-921112

Kanga Seating Package 12” w/mounting hardware

1300-921114

Kanga Seating Package 14” w/mounting hardware

Tools Needed: 5/32 allen wrench, 7/16 wrench or socket,

tape measure, pencil(1) Contoured seat.

Contents in package (qty)

(1) Contoured back

(1) #1300-7093

Left-side back hardware (hardware packet included)

(1) #1300-7095

Right-side back hardware (hardware packet included)

(1) #1300-7097

Seat knob clamp hardware

(1) #1300-7099

Seat-to-back hinge bolt packet

step two - Installing hardware to

wheelchair frame

step three - attaching seat/back

to wheelchair frame

2.1 Open the package labeled “seat knob clamp hard-

ware” loosen the large plastic hand knobs and attach the

seat knob clamps onto the seat mount brackets.

2.2 Locate the desired position for the seat/back within

the wheelchair frame. Using a pencil or a non-permanent

marking tool, mark the desired position for the seat/

back knob clamps on the wheelchair seat rails and back

canes. Remove the seat knob clamps from the seat mount

brackets.

2.3 Attach the seat knob clamps on the marked position

on the wheelchair seat rails.

2.4 Remove the right/left back knob clamps by loosening

the large plastic hand knobs.

2.5 Attach the right/left back knob clamp on the marked

positions on the wheelchair back canes.

2.6 Use tape measure and verify that both seat knob

clamps measure the same distance from a specific refer-

ence point on the wheelchair seat rails.

2.7 Repeat step 2.6 for the back knob clamps mounted to

the wheelchair back canes.

Attach the seat by aligning the seat mount brackets onto

the seat knob clamps attached to the wheelchair seat

rails.

Align the back knob brackets onto the back knob clamps

on the back canes.

Tighten all four of the large plastic hand knobs to secure

the seat/back in place.

Final adjustments for installing/removing seat/back, make

all necessary fine-tuning adjustments so that seat/back

assembly installs/removes properly. Do a final check and

tighten all hardware and plastic hand knobs prior to posi-

tioning client into wheelchair.

1.1 Locate the mounting base and mounting base hard-

ware packet.

1.2 Locate the (2) t-nut holes (through upholstery) on the

contoured back to attach the mounting base, carefully

cut upholstery to access t-nuts.

1.3 Using the mounting base hardware packet, attach (2)

screws/washers through the middle holes of the mount-

ing base to securely mount to the contoured back.

1.4 Locate the horizontal headrest bar and headrest

mounting ring and attach to headrest pad using the head-

rest pad mounting packet.

1.5 Complete the assembly by attaching the vertical Item.

assemblykanga comfort max headrest,

offset hardware

Item Number

4008-401010

Kanga Comfort Max Headrest, Offset Hardware, 10”

4008-401012

Kanga Comfort Max Headrest, Offset Hardware, 12”

4008-401014

Kanga Comfort Max Headrest, Offset Hardware, 14”

Tools Needed: 5/32 allen wrench, 3/16 allen wrench.

contents in package (qty)

(1) Offset multi-axis headrest bracket assembly

(1) Small 9 inch comfort max headrest pad

(1) Mounting base hardware packet

(1) Headrest pad mounting packet

kanga lateral trunk supports,

qr-removable

Item Number

3040-021010

Kanga Lateral Trunk Supports, Removable, 10” (pair)

3040-021012

Kanga Lateral Trunk Supports, Removable, 12” (pair)

3040-021014

Kanga Lateral Trunk Supports, Removable, 14” (pair)

Tools Needed: 5/32 allen wrench

Contents in package (qty):

(2) Track mount bracket

(1) QR lateral mounting packet

(2) QR mounting base

(2) lateral bracket, flush mount with pads (attached)

(2) lateral bracket, 1inch Offset (optional use)

NOTE - It is best to dry-fit hardware in-place prior to

cutting holes in upholstery. This installation is easiest with

the contoured back removed from the wheelchair, lying

rear side up flat on a solid surface.

1.1 On the rear side of contoured back ( I cut-out area)

choose either left or right side, locate the (2) t-nut holes

through upholstery, carefully cut upholstery to access

t-nuts.

1.2 Open the lateral mounting packet and remove (2)

screws, use screws to attach track mount bracket with

lateral assembly to the contoured back.

1.3 Repeat above steps for opposite side.

1.4 Locate the silver pull knob attached to the QR mount-

ing base, lift and rotate the knob to “unlocked” position.

1.5 Adjust the lateral bracket on the QR mounting base

to the desired width location, rotate and release the pull

knob to allow it to “lock” into desired hole on the lateral

bracket to hold desired lateral width position.

1.6 Lateral height adjustment; loosen the QR mounting

base and slide up or down track mount to desired height

position. Fully tighten all bolts to secure pads, brackets to

the track.

assembly

Item Number

1072-34410

Kanga Thigh Supports, Removable, 10” (pair)

11072-34412

Kanga Thigh Supports, Removable, 12” (pair)

11072-34414

Kanga Thigh Supports, Removable, 14” (pair)

Tools Needed: 5/32 allen wrench

Contents in package (qty):

(1) Mounting base hardware packet

(2) Thigh support assembly, flush mount with pads

(attached)

(2) Upper mounting brackets, 1inch Offset (optional use)

kanga thigh supports,

removable

NOTE - The 12inch and 14inch contoured seats come

with multiple thigh support mounting base t-nut locations,

it is best to dry-fit hardware in-place prior to cutting

upholstery. This installation is easiest with the contoured

seat removed from the wheelchair, lying bottom side up

flat on a solid surface.

1.1 Locate the spring loaded pull knob on bracket(s), to

remove simply pull knob and lift up on contoured pad. To

re-attach simply align upper bracket into seat mount base

receiver and push-click into place.

1.2 Locate the desired (2) t-nut holes (through upholstery)

on the bottom of contoured seat to attach the mounting

base (see note above), carefully cut upholstery to access

t-nuts.

1.3 Using the mounting base hardware packet, attach (2)

screws/washers through the mounting base slots and

secure to the contoured seat. Repeat steps for opposite

side.

assembly

Item Number

11060-10110

Kanga Abductor Pommel, Flip Down, 10”

11060-10112

Kanga Abductor Pommel, Flip Down, 12”

11060-10114

Kanga Abductor Pommel, Flip Down, 14”

Tools Needed: 1/8 allen wrench, 5/32 allen wrench.

Contents in package (qty):

(1) Flip down-removable abductor assembly with small pad.

(1) Mounting base with T-knob.

(1) Mounting base hardware packet.

kanga abductor pommel,

ﬂip down

assembly

1.1 Locate the mounting base and mounting base hardware

packet.

1.2 Locate the (2) t-nut holes (through upholstery) on the

bottom of contoured seat to attach the mounting base,

carefully cut upholstery to access t-nuts.

1.3 Using the mounting base hardware packet, attach (2)

screws/washers through the middle holes of the mounting

base to securely mount to the contoured seat.

1.4 Complete the installation by attaching the flip down

assembly to the mounting base and tightening the T-knob.

Adjust the pad height by loosening the 1/8 allen bolt on the

vertical bar.

kanga polycarbonate tray

Item Number

11060-10110

Kanga Abductor Pommel, Flip Down, 10”

11060-10112

Kanga Abductor Pommel, Flip Down, 12”

11060-10114

Kanga Abductor Pommel, Flip Down, 14”

Tools Needed: 3/8 open end wrench.

Contents in package (qty):

(1) Poly tray with toggle plates and toggle clamps

(attached)

1.1 Toggle clamp adjustment; if necessary to adjust toggle

clamps, slightly loosen the (2) 10-24 pressure nuts holding

the toggle clamp to the underside of the toggle plate.

Slide the toggle clamp into new position and re-tighten

both 10-24 pressure nuts firmly to hold in place.

1.2 Repeat above step for opposite side

Your Inspired by Drive branded product is warrantied

to be free of defects in materials and workmanship for

the lifetime of the product for the original consumer

purchaser.

This device was built to exacting standards and

carefully inspected prior to shipment. This Lifetime

Limited Warranty is an expression of our confidence

in the materials and workmanship of our products

and our assurance to the consumer of years of

dependable service.

This warranty does not cover device failure due to

owner misuse or negligence, or normal wear and

tear. The warranty does not extend to non-durable

components, such as rubber accessories, casters,

and grips, which are subject to normal wear and need

periodic replacement.

If you have a question about your Inspired by Drive

device or this warranty, please contact an authorized

Inspired by Drive dealer.

Limited Lifetime Warranty

Inhaltsverzeichnis

Andere Drive Rollstuhl Handbücher

Drive

Drive Blue Streak Bedienungsanleitung

Drive

Drive 12202KD-4 Bedienungsanleitung

Drive

Drive TRIDENT HD Bedienungsanleitung

Drive

Drive U-drive IFU Benutzerhandbuch

Drive

Drive Seren Powerchair Bedienungsanleitung

Drive

Drive DURO Bedienungsanleitung

Drive

Drive 550 600 100 Bedienungsanleitung

Drive

Drive 12021KD-1 Bedienungsanleitung

Drive

Drive Sunfire Plus EC Bedienungsanleitung

Drive

Drive NRS185008 Bedienungsanleitung

Drive

Drive TS19 Bedienungsanleitung

Drive

Drive Inspired WCM-2000-2G Bedienungsanleitung

Drive

Drive Expedition Plus Bedienungsanleitung

Drive

Drive enigma steel Wheelchair Bedienungsanleitung

Drive

Drive Silver sport Bedienungsanleitung

Drive

Drive SSP118FA-SF Bedienungsanleitung

Drive

Drive 12004KDRT-1 Bedienungsanleitung

Drive

Drive ASB-2109 Produkthandbuch

Drive

Drive DS250 Bedienungsanleitung

Drive

Drive RTL12203KDR Bedienungsanleitung

Drive

Drive BTR22BLK Bedienungsanleitung

Drive

Drive NRS185007 Bedienungsanleitung

Drive

Drive Sunfire Gladiator Bedienungsanleitung

Drive

Drive Cirrus Plus EC Power Handbuch

Beliebte Rollstuhl Handbücher anderer Marken

Otto Bock

Otto Bock Skippi plus Bedienungsanleitung

Invacare

Invacare Action 4NG series Bedienungsanleitung

SORG

SORG LoopSORG 802 Bedienungsanleitung

Designability

Designability WizzyBug Montageanleitung

Vermeiren

Vermeiren RAPIDO Bedienungsanleitung

Excel

Excel G5 KIDS 0285 Bedienungsanleitung

M. Bartels

M. Bartels SA-3 Bedienungsanleitung

Vermeiren

Vermeiren Turios Bedienungsanleitung

Invacare

Invacare Solara Spree GT Handbuch

nino robotics

nino robotics NIno Bedienungsanleitung

Invacare

Invacare MK5 EX Bedienungsanleitung

Nova

Nova TKW-12 Bedienungsanleitung

BCW

BCW Advantage Bedienungsanleitung

You-Q

You-Q Luca Bedienungsanleitung

interco

interco Ortolight Standard Bedienungsanleitung

Nova

Nova 7190L Bedienungsanleitung

Vermeiren

Vermeiren EZ1 Bedienungsanleitung

PaceSaver

PaceSaver Scout M-300 Bedienungsanleitung