DSC SEA-B-QUE Bedienungsanleitung

○

1○

2○

3○

4○

5○

6○

7○

8○

9○

1. DC+12V IN: Power input DC+12V/1.5A.

2. DC+12V OUT: DC+12V/750mA for camera only, and with an over current protector.

(Note: If you don’t use this port for cameras, you can use the DC+12V/500mA adaptor.)

3. ALARM IN: Once triggered, the built-in buzzer rings on for a 20-sec time. This port could be connected to

alarm sensor, e.g.: PIR Detector, Magnetic Reed Switch Detector.

4. AUDIO IN: RCA female for input audio signal.

5. VIDEO IN: BNC female for input video signal.

6. POWER/State LED: Indicated to power on and ARM status.

7. DISARM: Alarm ON / OFF selection.

8. CH SELECT (A B C D): 5.8GHz transmission channel selection.

9. ID AND ALARM MUTE: ID address setting is use for paring with receivers (RX unit). It must be make the

same code setting to link transmitter and receiver each other. The alarm mute function is use for muting built

-in buzzer at TX unit.

10. ANT: RP-SMA connector for connected to 5.8 GHz antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: TX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with RX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

○

1○

2○

3○

4○

5○

6○

7○

8○

1. DC+12V IN: Power input DC+12V/500mA.

2. ALARM OUT: Once triggered, the built-in buzzer and alarm remains on for a 20-sec time. This port could

be connected to alarm devices, e.g.: Siren, Flashing Unit.

3. AUDIO OUT: RCA female for audio signal output.

4. VIDEO OUT: BNC female for video signal output.

5. POWER/STATE LED: Indicated to power on or ARM and RF link status.

6. DISARM: Alarm ON / OFF selection.

7. CH SELECT (A B C D): 5.8GHz transmission channel selection.

8. ID AND ALARM MUTE: ID address setting is use for paring with transmitters (TX unit).

It must be make the same code setting to link transmitter and receiver each other. The alarm mute function

is use for muting built-in buzzer and disables the alarm output at RX unit.

9. ANT: RP-SMA connector for connected to 5.8 GHz antenna and built-in 3.3V / 25mA bias-tee circuit for an

active antenna.

*REMARK: When the frequency channels have the interference, adjust antenna or change the channel of transmitter

and don’t close to 802.11 a/b/g AP router and other 5.8GHz devices. (Note: Please keep 3 ~ 5 meter away)

* Panel View: RX unit

Bit 1 Bit 2 Bit 3 ID Address

(Pairing with TX)

Bit 4 Alarm Mute

00000ON

00111OFF

0102

0113

1004

1015

1106

1117

(1 = SW ON, 0 = SW OFF)

11/5/2009

Indications Power/State LED

Power On On

ARM High speed Flashing

RF Loss/Waiting TX Link Low speed Flashing

MODEL:DSC-5800VHK( :SK2-5800A)

5.8GH TX (Transmitter) ×1 5.8GH RX (Receivers) x1

Antenna ×2 User manual ×1

Screws x 4 ×2 Plastic-Conical-Anchor x 4 ×2

Power Adaptor (DC 12V/1.5A) ×1 Power Adaptor (DC 12V/500mA) x1

* Packing List:

Model No. TX RX

CHANNAL CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

FREQUENCY 5740

MHz

5752

MHz

5771

MHz

5790

MHz

5809

MHz

5828

MHz

5847

MHz

5760

MHz

RF IMPEDANCE 50 ΩTypical

5.8G BIAS-TEE 3.3V/25mA

MINIMUM RECEIVER SENSITIVITY -84dBm

POWER SUPPLY DC12V/1.5A Adaptor DC12V/500mA Adaptor

CURRENT CONSUMPTION 350mA 280mA Max.

DC OUTPUT DC12V/750mA

RF OUTPUT POWER 500mW

VIDE INPUT / VIDEO OUTPUT 1.0 Vp-p Composite @ 75Ω

AUDIO INPUT / VIDEO OUTPUT 2.0 Vp-p Typical, 3.0 Vp-p Max. @ 600Ω

ALARM INPUT TTL/CMOS (Level Detection)

ALARM OUTPUT NC/NO/COM (Dry Contact) Contact

Rating: AC 125V / 0.5A ; DC 24V / 1A

OPERATION TEMPERATURE 14° F ~ 122° F (-10°C ~ 50°C)

WEIGHT 5.8 Oz ( 164 g)

DIMENSIONS W x H x D: 110 x 30 x 88 mm (without Antenna)

* Specification :

11/5/2009

*** All Specifications are subject to change without notice.

1. Be careful, never let any water in this equipment.

2. If necessary, use a soft cloth moistened with alcohol to wipe off the dust.

3. Be extra careful not to shake the unit.

4. Avoid places where temperatures exceed 122° F (50°C)or higher.

5. Avoid places where there are frequent vibrations or shocks.

6. When any abnormalities occur, make sure to unplug the unit and contact your local dealer.

* Caution for Installation:

MODEL:DSC-5800VHK( :SK2-5800A)

FCC Part 15 Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pur-

suant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

3. Any changes or modifications (including the antennas) made to this device that are not ex-

pressly approved by the manufacturer may void the user’s authority to operate the equip-

ment.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DSC Sicherheitssystem Handbücher

DSC

DSC GSM 1000 Bedienungsanleitung

DSC

DSC Power632 PC1555 Bedienungsanleitung

DSC

DSC neo HS2016 Bedienungsanleitung

DSC

DSC PC5132-433 Bedienungsanleitung

DSC

DSC PowerSeries PC1864 Bedienungsanleitung

DSC

DSC IMPASSA Bedienungsanleitung

DSC

DSC SYSTEM MASTER PC4000 Bedienungsanleitung

DSC

DSC PC56O Bedienungsanleitung

DSC

DSC PowerSeries PC1832 Bedienungsanleitung

DSC

DSC iOtega Bedienungsanleitung

DSC

DSC WT5500 Bedienungsanleitung

DSC

DSC Power832 PC5015 Bedienungsanleitung

DSC

DSC Power608 Bedienungsanleitung

DSC

DSC PC 4010 Bedienungsanleitung

DSC

DSC PC 4020 - V3.0 Bedienungsanleitung

DSC

DSC 3G2055 Bedienungsanleitung

DSC

DSC neo HS2016 Bedienungsanleitung

DSC

DSC LC-171 Handbuch

DSC

DSC PowerSeries PC5108FLR Bedienungsanleitung

DSC

DSC Power632 PC1555 Bedienungsanleitung

DSC

DSC PowerSeries Bedienungsanleitung

DSC

DSC neo HS2016 Bedienungsanleitung

DSC

DSC neo HS2016 Bedienungsanleitung

DSC

DSC Classic PC580 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung