DTS XR2000 BEAM Bedienungsanleitung

Made in Italy

XR2000 BEAM

User’s Manual Rel 1.4

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

D.T.S

D.T.S.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S.

ARC 1200

XR2000 BEAM

ARC 1200

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 7

6- IMPORTANT SAFETY INFORMATION 8

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING THE LAMP 9

7.1 Lamp alignment

8- VOLTAGE AND FREQUENCY 10

9- INSTALLATION 10

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 11

10.1 Protection

11- DMX SIGNAL CONNECTION 12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 13

13- DISPLAY FUNCTIONS 14

14- ERROR MESSAGES 17

15- HIDDEN MENU 18

16- PAN & TILT SPEED 19

17- FANS SPEED 19

18- OPENING THE PROJECTOR HOUSING 20

19- REPLACING GOBOS 20

20- PERIODIC CLEANING 21

20.1 Lenses and reflectors

20.2 Fans and air passages

21- PERIODIC CONTROLS

22- DMX PROTOCOL 22

23- 8 MOTORS CONTROL CARD 34

24- PAN & TILT CARD 35

25- CABLES RESEND CARD

26- DISPLAY CARD

27- LAMP ON-OFF CONTROL CARD

28- ROTATING GOBO WHEEL 36

29- COLOUR WHEEL 1 37

30- MORE GOBOS PROVIDED IN THE PACK AS STANDARD ACCESSORIES 38

3XR2000 BEAM

ARC 1200

1- SYMBOLS

Graphic symbols used on this manual

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information

regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or experienced

person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON

INFLAMMABLE SURFACES”

2M THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO

BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP

CAN CAUSE DAMAGE TO EYES AND SKIN”

XR2000 BEAM

ARC 1200

4- TECHNICAL FEATURES

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit

Automatic switching ON of lamp in case of accidental switching OFF.

Lamp ON/OFF via DMX; Reset via DMX.

Optical group

XR2000 BEAM is a new compact moving head with an extremely high light power, projecting a parallel

and very concentrated beam.

With its new lens unit, XR2000 BEAM generates a luminosity of an incredible 150,000 Lux at 5 metres,

using only a 700 W lamp, giving an exceptional balance between performance and power consumption.

XR2000 BEAM is designed for a wide range of professional applications, like concerts, shows, tours and

big events.XR2000 BEAM ensures in fact great flexibility in use, because in a single projector it

incorporates a range of functions normally available only on different units (long-throw projectors with

high-power lamps, PAR 64 ACL, moving heads).XR2000 BEAM offers:

* Exceptional light power (150,000 Lux at 5 metres);

* The capacity to project a highly condensed and intense beam of light even over great distances, thanks

to the high efficiency of the new lens;

* Variety of colours (linear CMY synthesis + wheel with 7 colours);

* Customizable gobo wheel;

* Insertable linear frost filter (soft edge);

* Fast and uniform Pan and Tilt movements.

The XR2000 BEAM is also the ideal light for a vast range of applications in which quiet operation is a

priority, thanks to its silent ventilation system and silent pan/tilt operation.

The 16 bit Pan/Tilt mechanism features an exclusive Super Speed function, and a locking system with

recessed buttons. Access to every feature of the internal menu is simple and direct, thanks to the new

user interface featuring a LCD backlit graphic display (128 x 64).

XR2000 BEAM

(Cod. 03.MB001.EB.L)

• Electronic ballast 90-245V 50/60 Hz • Black finish

150.000 Lux at 5 m (5,5°beam angle)

Dichroic glass reflector

Dimmer / shutter / strobo

Linear dimmer

Shutter

Strobe from 0,85 flash/sec to 10 flash/sec

Colours

CMY colour synthesis system + colour wheel (7 colours + open) with linear selection for perfect 2-colour

beams

Colour change with blackout sync; rainbow effect

Gobos

1 customizable rotating gobo wheel (7 gobos); extractable gobo holders

Gobo change with synchronized blackout

Gobo scrolling; Gobo shake

Frost

Frost filter (soft edge)

5XR2000 BEAM

4- TECHNICAL FEATURES

Pan / Tilt

DMX channels

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

POWERCONN connector by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz)

Power consumption: 820 W

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection

Thermal

Operating ambient temperature: -10° / 40°

Weight

37 Kg

Pan 540°(3,9 sec.); Tilt 270°(2,6 sec.); 16-bit resolution

Super Speed function; extremely smooth and precise movements even at the highest speeds

Pan / Tilt locking system with recessed buttons

Automatic Pan/Tilt repositioning in case of knocks

21(default) or 16 DMX channels

Internal operating system updatable via DMX

Interface

LCD backlit graphic display (128x64)

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

ARC 1200

6XR2000 BEAM

4- TECHNICAL FEATURES

Dimensions

5- ACCESSORIES

As standard

•1 x MSR Gold 700/2 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•5 x Metal Gobos

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• User’s manual

Optional (on request)

• Double Professional Flight case; compartment for lamps and accessories, swivel wheels, cover with

hinges with-stay, dishes on cover for piling, 8 handles (2 each side) (cod. 0521C038)

• Raincover for XR2000 base (top) (cod. 03.MA009)

• Raincover for XR2000 base (bottom) (cod. 03.MA010)

• Embedding flange for XR2000 (visible display) (cod. 03.MA008)

• Embedding flange for XR2000 (no visible display) (cod. 03.MA007)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C”Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C”Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C”Clamp GQUICK with “Fast Lock”connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C”Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock”connection 1⁄4 turn

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

Unit Dimensions (LxWxH)

510x510x775mm

Weight: 37 Kg

Packaging Dimensions (LxWxH)

610 x 540 x 720 mm

Weight: 42 Kg

ARC 1200

7XR2000 BEAM

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

MSR Gold 700 Fastfit lamp

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1.5 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology inherent in the requires the assistance of specialised personnel

for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid objects is IP 20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

•

XR2000 BEAM uses a PHILIPS /2

XR2000 BEAM

Raincover for XR2000 base (top) (cod. 03.MA009)

Raincover for XR2000 base (bottom) (cod. 03.MA010)

ARC 1200

XR2000 BEAM

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

2) Insert the lamp (photo2).

3) Rotate the lamp 1/4 turn clockwise (photo 3 and 4).

The lamp used on XR2000 BEAM is made in quartz glass and should be handled with care. Always

follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue

provided in the lamp's packaging. The lamp socket is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.

WARNING: Never look directly at the lamp when it’s lit.

Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit. The lamp alignment is also essential to obtain the

maximum unifirmity and luminous performance by the projection.

3 adjusters X, Y and

Z (photo 5)

you will have an evenly projected light beam, with no shadows or

zones wich are brighter than others.

Philips MSR Gold 700/2 Fastfit

Power 700W

Luminous flux 50,000 lm

Colour temperature 7.500°K

Lampbase PGJX50

Rated life 750 hours

PGJX50

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface

no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto

the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the

until you achieve a uniform flat field.

When the lamp is correctly optimized,

ARC 1200

Photo 2Photo 1 Photo 4Photo 3

Photo 5

Lamp

Alignment

XR2000 BEAM

8- VOLTAGE AND FREQUENCY

The XR2000 BEAM with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR2000 BEAM may be either floor or ceiling mounted.

For floor mounting installations, the XR2000 BEAM is supplied with four rubber mounting feet on the

base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to

move or shake whilst the XR2000 BEAM is moving.

Eight 1/4 turn Fast Locks connections placed in the base of the units allow to fix the XR2000 BEAM in

any position, by using the two Fast Lock ‘C’ clamps provided in the box.

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the XR2000 BEAM and to the suspension

truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the

iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the

picture below.

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

ARC 1200

XR2000 BEAM

Andere DTS Beleuchtungsausrüstung Handbücher

DTS

DTS Z8 Bedienungsanleitung

DTS

DTS Thomas & Betts NT 06 Handbuch

DTS

DTS Nick Wash 600 Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS DONUT 6 Bedienungsanleitung

DTS

DTS SCENA LED 80 WHITE Bedienungsanleitung

DTS

DTS FOS 100 WHITE 36 Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS NicKWash 600 Bedienungsanleitung

DTS

DTS PROFILO 500 Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS Scena LED 150 Bedienungsanleitung

DTS

DTS HORUS FULL COLOUR Bedienungsanleitung

DTS

DTS JACK Bedienungsanleitung

DTS

DTS XR5 SPOT Bedienungsanleitung

DTS

DTS PAR64Ip66 watertight Bedienungsanleitung

DTS

DTS A.R.C. Bedienungsanleitung

DTS

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Bedienungsanleitung

DTS

DTS XM 1200 SPOT Bedienungsanleitung

DTS

DTS TITAN SOLO Bedienungsanleitung

DTS

DTS MOON 575 Bedienungsanleitung

DTS

DTS ALCHEMY 5 Bedienungsanleitung

DTS

DTS Raptor Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

LCG

LCG Thunder 400 Bedienungsanleitung