DTSystems NO BARK TRAINER Bedienungsanleitung

D.T. SYSTEMS, INC.

2872 Walnut Hill Lane

Dallas, Texas 75229

Tel: (214) 350-9446

Fax: (214) 350-7847

www.dtsystems.com

customerservice@dtsystems.com

D.T. SYSTEMS, INC.

1145DT

NO BARK TRAINERTM

INSTRUCTION MANUAL

TABLE OF CONTENTS

•

Introduction ..................................................3

•

Features ........................................................4

•

Package Contents .........................................4

•

Parts & Functions .........................................5

•

Choosing the Correct

Electrodes and Sensors.................................6

•

Adjusting and Positioning Your Collar........7

•

Operation......................................................8

•

Changing the Battery....................................9

•

Testing..........................................................10

•

Maintenance .................................................10

•

Important Safety Notes................................. 11

•

Warranty.......................................................11

•

Contact Information .....................................12

IMPORTANT SAFETY NOTES

•

Before beginning bark training your dog should be examined by a veteri-

narian to assure that there are no physical reasons for your dog’s exces-

sive barking and to assure that your dog in good health.

•

Since no electronic device is perfect, there is an extremely slim possibil-

ity that your dog may receive an unintentional electric stimulation.

Therefore never leave the unit on your dog while unsupervised.

•

Your 1145DT No Bark Trainer is a very valuable tool if used correctly.

Therefore it is extremely important that you completely understand all

functions of the collar and how to properly train with it before placing it

on your dog.

•

The electrodes on this collar are made with high grade stainless steel to

help prevent any chemical or allergic reactions with your dog’s skin.

•

To prevent neck irritation, the collar should never be worn for more than

12 hours a day. Daily changing the collar location on the dog’s neck will

also help prevent irritations. It is important to keep the collar clean.

Clean the electrodes regularly with a mild anti-bacterial soap.

•

If an irritation is found, carefully wash the dog’s neck with soap and

water and then wipe the area with Hydrogen peroxide. Dry thoroughly

and apply an antibiotic ointment.

WARRANTY

All 1145DT No Bark Trainers have a Six Month Parts and Labor Warranty,

effective from the original date of purchase. (A copy of the original sales

receipt is required to validate the date of purchase).

NOTE

1145DT batteries are replaceable/disposable and are not covered under the

warranty.

Damage by user, abuse or loss of parts, and attempted repair damage by the

user or his agent are not covered. All repairs, whether warranted or not,

should be sent to the address on the last page of this manual.

TESTING

1. Place the two red wires from the Test Light onto the

electrodes (as shown in the picture above).

2. Turn the unit ON using either magnet.

3. Slide the bottom of the test light (the serrated edge) across the top

of the sensor.

4. If the light comes on, the unit is functioning properly.

• Higher intensity levels will cause the Tester to light up brighter.

• If the tester doesn’t light, wait 3 seconds then repeat the process.

MAINTENANCE

• It is very important to periodically clean your 1145DT No Bark

trainer for maximum performance. Regular cleaning will also

lengthen the life of your unit.

• Clean the 1145DT collar box with lukewarm water and a mild

anti-bacterial soap.

• Take care to thoroughly clean the space between the electrodes

and the belt.

• The belt and buckle should be cleaned with water and a mild soap

then allowed to dry completely.

• Always allow the entire unit to completely dry before

using. Never completely submerge the unit.

INTRODUCTION

Congratulations and Thank you for purchasing the

1145DT No Bark Training System. This collar is one

of the best and most advanced No Bark Trainers in

the World.

The 1145DT has been specially designed for training

your dog and for preventing excessive barking by

automatically sending out an electrical stimulation

whenever problem barking occurs. This training system

is ideal for all dog temperaments from the most stubborn

to the meekest.

IMPORTANT

It is recommended that you fully read and understand

this entire owner’s manual prior to operating your

1145DT No Bark Trainer. If you have any questions

or do not fully understand any part of this manual, or

the product’s features or operation please contact our

customer service department at the phone number or

address on the back of this manual.

The 1145DT is perfect for:

•

Preventing excessive barking at home, in a kennel or

while traveling.

•

Preventing your dog from howling at night.

•

Preventing your dog from barking in restricted areas.

• Completely Digital Micro-processor System.

• Adjustable Collar fits small to large dogs.

• Replaceable 6 Volt Battery

• System delivers 1/2 second corrective stimulation.

• Automatic three-second safety delay.

• Built in Magnetic ON/OFF system.

• Magnet built right into the collar clip. (No more

lost magnets)

• Digital Numeric Display shows 8 different intensity

levels.

• Vibration Sensor only picks up vocal cord

vibrations eliminating unnecessary “shock” from

extraneous noises or dog’s tags.

• Data Memory System saves last used intensity

setting.

• Completely Waterproof.

FEATURES

The newly redesigned 1145DT No Bark Training

System features:

PACKAGE CONTENTS

1145DT No Bark Collar - Size: 2.3” X1.6” X1.1” Weight: 4 oz.

1/2” Electrodes & 1/2” Sensor

3/4” Electrodes & 3/4” Sensor

Key-Ring Magnet Test Light

(Battery Not Included)

CHANGING THE BATTERY

Follow these steps to change the battery on the 1145DT:

1) Use a coin or screw driver to open the battery

compartment cap by turning it counter-clockwise.

2) Remove the old battery.

3) Insert the new battery positive “+” side first into the

battery compartment.

4) Close the battery cap in a clockwise direction.

NOTE

Use only 6 Volt Alkaline or Lithium Battery.

(Lithium will last longer)

CAUTION

Make sure to check that the cap is properly closed and

tightened to prevent water leakage.

OPERATING THE 1145DT

Turning the 1145DT ON & OFF:

Turning the Unit ON:

•

Touch either magnet to the White Dot on the side of the

1145DT collar box for approximately one half second

until the number 0 flashes briefly on the LED Display.

•

The number 0 will be followed immediately by another

number (0-8) which will flash for approximately

1.5 seconds. This indicates on which intensity level the

unit is currently set.

•

The small sub LED light on the display will blink steadily

every 2.5 seconds to let you know the unit is ON and

functioning properly.

Turning the Unit OFF:

•

Touch either magnet to the white dot for 2 seconds. The

number 0 will quickly blink twice on the display. This

indicates the unit is now off.

Changing the Stimulation Level

While the unit is on quickly touch either magnet to the White

Dot (less than one second). Each time a magnet touches the

White Dot the stimulation level will increase by one level.

The level will flash in the display for 1/2 second. When the

level reaches 8 the next touch will reset the unit back to 0.

PARTS & FUNCTIONS

•

The collar belt is adjustable from approximately 7” to

approximately 21”.

•

The round circle on the clip with D.T.S. imprinted on it is a

magnet for turning the unit ON/OFF and changing intensity

levels. (You can also use the key ring magnet.)

•

The White dot on the collar box is where you hold one of

the magnets to turn the unit ON/OFF and change intensity

levels.

•

The display shows an LED number to indicate the current

intensity level and also has a small blinking light to let you

know the unit is ON.

•

The Sensor is vibration sensitive and is designed to not be

activated by extraneous noises (including rattling dog tags

or other dogs barking).

•

The unit starts on intensity level Zero and cycles through

intensity level Eight then back to Zero.

CHOOSING THE CORRECT

ELECTRODES AND SENSORS

Choosing the proper electrode and sensor length is vital to

the proper operation of the unit.

Electrodes and sensors should be long enough to make

good contact with the dog’s skin without being so long as

to interfere with the dog’s normal breathing.

***Tip: With some longer haired dogs it can be beneficial

to trim the hair around the area of the voice box.***

CAUTION

When screwing in the electrodes and sensor,

tighten by hand only. Proper hand tightening will

allow the electrodes and sensor to vibrate for

maximum stimulation. Over tightening can cause

damage to the unit.

ADJUSTING & POSITIONING YOUR COLLAR

FOR PROPER FIT

•

All electronic collars need to be very snug to work

properly. They must be just tight enough to allow the

electrodes and the sensor to make good skin contact.

•

If your collar is too loose, the stimulation may not work

properly because good skin contact is not being achieved.

This can directly affect the stimulation performance and

whether or not the dog will receive the stimulation. Always

check for good contact if it appears that your dog is not

responding to the stimulation.

•

A loose collar can promote skin irritation from moving or

rubbing too much on a dog’s neck while they are running or

training. The proper snug fit will help prevent this from

occurring.

•

Proper fit of the collar is extremely important. It should be

just tight enough on the dog’s neck to make good skin

contact while still allowing the dog to breath normally. The

collar should never be so tight that it restricts the dog’s

normal breathing pattern.

•

For proper positioning of your collar receiver box, it should

be placed so that the electrodes and sensor are facing the

dog’s vocal cords.

•

Check your dog’s neck daily for signs of possible irritation.

Proper collar tightness and position are very important to

insure safety and correct functioning every time you use

the collar.

CHOOSING THE CORRECT

ELECTRODES AND SENSORS

Choosing the proper electrode and sensor length is vital to

the proper operation of the unit.

Electrodes and sensors should be long enough to make

good contact with the dog’s skin without being so long as

to interfere with the dog’s normal breathing.

***Tip: With some longer haired dogs it can be beneficial

to trim the hair around the area of the voice box.***

CAUTION

When screwing in the electrodes and sensor,

tighten by hand only. Proper hand tightening will

allow the electrodes and sensor to vibrate for

maximum stimulation. Over tightening can cause

damage to the unit.

ADJUSTING & POSITIONING YOUR COLLAR

FOR PROPER FIT

•

All electronic collars need to be very snug to work

properly. They must be just tight enough to allow the

electrodes and the sensor to make good skin contact.

•

If your collar is too loose, the stimulation may not work

properly because good skin contact is not being achieved.

This can directly affect the stimulation performance and

whether or not the dog will receive the stimulation. Always

check for good contact if it appears that your dog is not

responding to the stimulation.

•

A loose collar can promote skin irritation from moving or

rubbing too much on a dog’s neck while they are running or

training. The proper snug fit will help prevent this from

occurring.

•

Proper fit of the collar is extremely important. It should be

just tight enough on the dog’s neck to make good skin

contact while still allowing the dog to breath normally. The

collar should never be so tight that it restricts the dog’s

normal breathing pattern.

•

For proper positioning of your collar receiver box, it should

be placed so that the electrodes and sensor are facing the

dog’s vocal cords.

•

Check your dog’s neck daily for signs of possible irritation.

Proper collar tightness and position are very important to

insure safety and correct functioning every time you use

the collar.

OPERATING THE 1145DT

Turning the 1145DT ON & OFF:

Turning the Unit ON:

•

Touch either magnet to the White Dot on the side of the

1145DT collar box for approximately one half second

until the number 0 flashes briefly on the LED Display.

•

The number 0 will be followed immediately by another

number (0-8) which will flash for approximately

1.5 seconds. This indicates on which intensity level the

unit is currently set.

•

The small sub LED light on the display will blink steadily

every 2.5 seconds to let you know the unit is ON and

functioning properly.

Turning the Unit OFF:

•

Touch either magnet to the white dot for 2 seconds. The

number 0 will quickly blink twice on the display. This

indicates the unit is now off.

Changing the Stimulation Level

While the unit is on quickly touch either magnet to the White

Dot (less than one second). Each time a magnet touches the

White Dot the stimulation level will increase by one level.

The level will flash in the display for 1/2 second. When the

level reaches 8 the next touch will reset the unit back to 0.

PARTS & FUNCTIONS

•

The collar belt is adjustable from approximately 7” to

approximately 21”.

•

The round circle on the clip with D.T.S. imprinted on it is a

magnet for turning the unit ON/OFF and changing intensity

levels. (You can also use the key ring magnet.)

•

The White dot on the collar box is where you hold one of

the magnets to turn the unit ON/OFF and change intensity

levels.

•

The display shows an LED number to indicate the current

intensity level and also has a small blinking light to let you

know the unit is ON.

•

The Sensor is vibration sensitive and is designed to not be

activated by extraneous noises (including rattling dog tags

or other dogs barking).

•

The unit starts on intensity level Zero and cycles through

intensity level Eight then back to Zero.

• Completely Digital Micro-processor System.

• Adjustable Collar fits small to large dogs.

• Replaceable 6 Volt Battery

• System delivers 1/2 second corrective stimulation.

• Automatic three-second safety delay.

• Built in Magnetic ON/OFF system.

• Magnet built right into the collar clip. (No more

lost magnets)

• Digital Numeric Display shows 8 different intensity

levels.

• Vibration Sensor only picks up vocal cord

vibrations eliminating unnecessary “shock” from

extraneous noises or dog’s tags.

• Data Memory System saves last used intensity

setting.

• Completely Waterproof.

FEATURES

The newly redesigned 1145DT No Bark Training

System features:

PACKAGE CONTENTS

1145DT No Bark Collar - Size: 2.3” X1.6” X1.1” Weight: 4 oz.

1/2” Electrodes & 1/2” Sensor

3/4” Electrodes & 3/4” Sensor

Key-Ring Magnet Test Light

(Battery Not Included)

CHANGING THE BATTERY

Follow these steps to change the battery on the 1145DT:

1) Use a coin or screw driver to open the battery

compartment cap by turning it counter-clockwise.

2) Remove the old battery.

3) Insert the new battery positive “+” side first into the

battery compartment.

4) Close the battery cap in a clockwise direction.

NOTE

Use only 6 Volt Alkaline or Lithium Battery.

(Lithium will last longer)

CAUTION

Make sure to check that the cap is properly closed and

tightened to prevent water leakage.

TESTING

1. Place the two red wires from the Test Light onto the

electrodes (as shown in the picture above).

2. Turn the unit ON using either magnet.

3. Slide the bottom of the test light (the serrated edge) across the top

of the sensor.

4. If the light comes on, the unit is functioning properly.

• Higher intensity levels will cause the Tester to light up brighter.

• If the tester doesn’t light, wait 3 seconds then repeat the process.

MAINTENANCE

• It is very important to periodically clean your 1145DT No Bark

trainer for maximum performance. Regular cleaning will also

lengthen the life of your unit.

• Clean the 1145DT collar box with lukewarm water and a mild

anti-bacterial soap.

• Take care to thoroughly clean the space between the electrodes

and the belt.

• The belt and buckle should be cleaned with water and a mild soap

then allowed to dry completely.

• Always allow the entire unit to completely dry before

using. Never completely submerge the unit.

INTRODUCTION

Congratulations and Thank you for purchasing the

1145DT No Bark Training System. This collar is one

of the best and most advanced No Bark Trainers in

the World.

The 1145DT has been specially designed for training

your dog and for preventing excessive barking by

automatically sending out an electrical stimulation

whenever problem barking occurs. This training system

is ideal for all dog temperaments from the most stubborn

to the meekest.

IMPORTANT

It is recommended that you fully read and understand

this entire owner’s manual prior to operating your

1145DT No Bark Trainer. If you have any questions

or do not fully understand any part of this manual, or

the product’s features or operation please contact our

customer service department at the phone number or

address on the back of this manual.

The 1145DT is perfect for:

•

Preventing excessive barking at home, in a kennel or

while traveling.

•

Preventing your dog from howling at night.

•

Preventing your dog from barking in restricted areas.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DTSystems Tierpflegeprodukte Handbücher

DTSystems

DTSystems Super Trainer EZT plus 5000 Bedienungsanleitung

DTSystems

DTSystems CDT 1000 PLUS Bedienungsanleitung

DTSystems

DTSystems Micro-iDT PLUS Series Bedienungsanleitung

DTSystems

DTSystems Ultra-e 2010 Bedienungsanleitung

DTSystems

DTSystems DT-Good dog ST300 Pro Bedienungsanleitung

DTSystems

DTSystems R.A.P.T. 1400 Bedienungsanleitung

DTSystems

DTSystems RH1202 Bedienungsanleitung

DTSystems

DTSystems BTB 809 Bedienungsanleitung

DTSystems

DTSystems Micro-iDT Z3000 Bedienungsanleitung

DTSystems

DTSystems RedHead RH Pro 1000 Bedienungsanleitung

DTSystems

DTSystems RedHead RH 300 Bedienungsanleitung

DTSystems

DTSystems Micro-iDT Z3000 Bedienungsanleitung

DTSystems

DTSystems Super Trainer EZT plus Series Bedienungsanleitung

DTSystems

DTSystems SUPER TRAINER EDT 100 Bedienungsanleitung

DTSystems

DTSystems Ultra Min-e 2090 Bedienungsanleitung

DTSystems

DTSystems RDL 1209 Bedienungsanleitung

DTSystems

DTSystems SPT 2420 Bedienungsanleitung

DTSystems

DTSystems H2O 1810 PLUS Bedienungsanleitung

DTSystems

DTSystems 1125DT Bedienungsanleitung

DTSystems

DTSystems SUPER PRO LITE TRAINER SPT Series Bedienungsanleitung

DTSystems

DTSystems H2O 1810 PLUS Bedienungsanleitung

DTSystems

DTSystems H20 1810 PLUS Bedienungsanleitung

Beliebte Tierpflegeprodukte Handbücher anderer Marken

Schwinn

Schwinn Rascal Bedienungsanleitung

K&H

K&H Small Animal Bedienungsanleitung

SHOR-LINE

SHOR-LINE 006.3230.00 Bedienungsanleitung

Petsafe

Petsafe Stubborn Dog Receiver Collar Bedienungsanleitung

Datamars

Datamars OMNI MAX Bedienungsanleitung

Trixie

Trixie 24444 Bedienungsanleitung

Roverpet

Roverpet 30DDPP Bedienungsanleitung

SportDOG

SportDOG SD-105S-C Bedienungsanleitung

Staywell

Staywell 400 Series Magnetic Bedienungsanleitung

Dogtek

Dogtek Sonic Birdhouse Bedienungsanleitung

Togfit

Togfit Deluxe Trigger Lock Door Gate Bedienungsanleitung

Girafus

Girafus 227PA Bedienungsanleitung

ubbink

ubbink KoiFeeder Solar Bedienungsanleitung

ULTRACOM

ULTRACOM KOIRA-GPS Bedienungsanleitung

CADOCA

CADOCA Deuba 106911 Bedienungsanleitung

Dogtra

Dogtra RR Deluxe Bedienungsanleitung

Carson

Carson CONVERTIBLE PET YARD 2200 Bedienungsanleitung

Creative Cedar Designs

Creative Cedar Designs K-9 Kabin Bedienungsanleitung