Duke TSC-6/18M Bedienungsanleitung

MAIN CONTROLLER

REPLACEMENT INSTRUCTIONS FOR:

P/N 120107

REV C 05/22/2019

INSTALLATION

INSTRUCTIONS

Items required for this installation:

• #2 Phillips Screw Driver

• 11/32” Nut-driver

• ESD Wrist Strap (included in kit)

This kit contains:

Main Control Module Assembly For:

• ELC0017-1 - PCB, TSC, TSCM

• ELC0017-7 - PCB, TSC, PBC

• 512418 Strap, Disposable Wrist ESD

Reproduction without written permission is prohibited. Duke is a registered

trademark of the Duke Manufacturing Co.

CAUTION: Please read this manual completely before attempting

to install, operate or service this equipment

DUKE KITS

# 600309 - TSC-6/18M

# 600546 - PBC-6/18M

Main Controller Replacement Instructions:

TSC-6/18 and PBC-6/18

1. Verify the Main Control Module Assembly

requires replacement prior to proceeding.

Reference Service Manual Troubleshooting

Guide.

2. Verify recipe settings (recipe names and set

points) with store sta prior to replacement.

Record recipe setting for reference to reprogram

any variance in recipes names and set points on

the new control after replacement.

3. Turn OFF the unit’s Power Switch on the left side

middle of the oven.

NOTE: The Main Control Module Assembly

is 12VDC supplied only and is isolated from

dangerous or high voltages by inner safety

cover inside the controls cavity behind the

exterior controls panel.

4. Loosen, but do not remove the bottom and rear

screws on the slide out. Remove top left and top

right screws.

5. Slide the control panel forward and tilt down the

control panel.

6. Connect ESD Wrist strap to Unit in location

shown.

Attach

ESD Strap

to flange

7. Place ESD strap on wrist and tighten. Strap

must be tight around wrist to be eective.

8. Unplug the two connectors on the back of the

Main Control assembly in the unit.

Loosen

Remove

REMOVAL OF OLD CONTROL

Main Controller Replacement Instructions:

TSC-6/18 and PBC-6/18

9. Remove the outer 4 corner retaining nuts that

mount the Main Control Module Assembly to

the inner controls panel.

Do not remove the center nuts or PCB cover of the Main Control

Module Assembly. Warranty may be voided if cover has been

removed or tampered with.

1. Using proper ESD procedures, remove the

replacement Main Control Module Assembly

from the shipping box. Visually inspect the new

Main Control Module Assembly for damage.

If damage is identied, do not install the new

control and immediately contact Duke Service

Department for instruction.

2. A display glass protector must be removed from

the new Main Control Module Assembly display

glass before installing. The protector is a clear

transparent plastic layer over the glass which is

easily removed by hand. Contact Duke Service if

you have question about the glass protector.

Remove Outer

Nuts

Do not remove

2 Center Nuts

Remove Outer

Nuts

INSTALLING NEW CONTROL

3. To prevent static cling between the display

and overlay, lightly dust the display glass with

baby powder or talc powder. Gently remove

powder by brushing with a cosmetic brush (as

shown below). Do not wipe the display with

hands or any cloth as this may scratch the glass.

Additionally, do not put any powder on the

overlay.

5. Repack the prior / damaged Main Control

Module Assembly in the ship packaging for

return shipment to Duke Manufacturing.

6. Remove the ESD Wrist Strap.

7. Turn ON the left side power switch and verify

the LED indicators on the new Main Control

Module PCB Assembly are active (viewed

through the rear cover window. The PCB LED’s

will activate as the control boots and while

running. Go to the Troubleshooting Guide if

LEDs do not activate.

4. Remove the prior / damaged Main Control

Module Assembly from the mounting studs

and place the new replacement Main Control

Module Assembly. Verify the new Main Control

Module display is centered in the control panel

window. Reinstall the 4 retaining nuts and

reconnect the 2 PCB header connections.

Duke Manufacturing Co.

2305 N. Broadway

St. Louis, MO 63102

Phone: 314-231-1130

Toll Free: 1-800-735-3853

Fax: 314-231-5074 www.dukemfg.com

Main Controller Replacement Instructions:

TSC-6/18 and PBC-6/18

12. Touch / select the top right “info” button (circled

exclamation point) on the display. Touch / select

the upper left “User” icon. Touch / select the

“System Status”button and verify input levels

and output loads are functioning as expected.

13. Exit to the PIN code screen and program the

prior recorded recipe names and set points if

they are dierent from the new Main Control

Module Assembly’s recipe settings.

14. Allow the unit to run until Preheat cycles are

complete and the Oven and Proofer are in

“READY” modes. Verify Proofer RH is active

via proofer door glass visual. Verify Oven and

Proofer temperatures reasonably correlate with

other temperature measurement equipment.

8. Tilt up and slide back the control panel. Replace

the Top 2 screws and tighten all 8 screws on

both sides. Verify the Duke logo screen or the

“gray” button start screen is properly displayed.

NOTE: Verify wiring is not trapped or

visible under the controls panel after fully

slid into position.

9. Turn OFF and turn back ON the left side power

switch while watching the control display.

Record the software version identier (Example

“A005.88F”) at the bottom of the Duke Logo

screen. Repeat O / On cycle if the software

version I.D. is missed during the automatic logo

screen view.

10. From the “gray” screen, select either the Oven

icon or an Oven recipe and verify the Oven

lights turn ON and verify fault messages are not

displayed in the top tool bar of the display. Go to

the Troubleshooting Guide if Oven lights do not

turn ON.

11. Select either the Proofer icon or a Proofer recipe

and verify the Proofer lights turn ON and verify

fault messages are not displayed in the top tool

bar of the display. Go to the Troubleshooting

Guide if Proofer light do not turn ON.

NOTE: The units controls and sensors are

high precision and should not require

to be recalibrated. Up to 10% variances

between the measurement device and

the units controls are most probably due

to measurement equipment accuracy

and not the units control system. Contact

Duke Service should any sensor calibration

questions arise.

Andere Handbücher für TSC-6/18M

Dieses Handbuch passt für folgende Modelle

Andere Duke Controller Handbücher

Duke

Duke 600183 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch