Dungs DMV Series Bedienungsanleitung

1 … 2

MC • Karl Dungs, Inc. • DMV/6x2 Series Coil Replacement • Edition 2016.02 • P/N 261408

DMV/6x2 Series

Coil Replacement

Installation Instructions

Table of Contents

USA CDN

Table of Contents ........................Page 1

Attention ................................Page 1

Procedure ...............................Page 2

1, 2, 3 ... = Action

• = Instruction

Explanation of symbols

On completion of work on the

safety valve, perform a leakage

and function test.

Please read the instruction be-

fore installing or operating. Keep

the instruction in a safe place. You

nd the instruction also at www.

dungs.com If these instructions

are not heeded, the result may

be personal injury or damage to

property.

Any adjustment and application-

specic adjustment values must

be made in accordance with the

appliance-/boiler manufacturers

instructions.

Attention

Check the ratings in the speci-

cations to make sure that they

are suitable for your application.

[V][A]

[Hz][VA]

Safety

first

O.K.

Theinstallationandmaintenance

of this product must be done

under the supervision of an ex-

periencedand trainedspecialist.

Never perform work if gas pres-

sure or power is applied, or in

the presence of an open ame.

2 … 2

MC • Karl Dungs, Inc. • DMV/6x2 Series Coil Replacement • Edition 2016.02 • P/N 261408

Procedure

1. Disconnect all power to prevent electrical shock and

equipment damage.

2. Closetheupstreammanualshutovalve.

3. Remove DIN electrical connector.

4. Remove blue paint from the countersunk screw on the

hydraulic brake unit (DMV-DLE series) or black adjustment

knob (DMV-D series). (Fig. 1)

5. Remove the pan head screw on the hydraulic brake unit

(DMV-DLE series) or black adjustment knob (DMV-D

series). (Fig. 1)

6. Liftothehydraulicbrakeunitorblackadjustmentknob.

7. Remove washer.

8. Remove solenoid by pulling directly up. Note solenoid #

and voltage.

9. Verify the replacement coil has the same coil # and electri-

cal rating. Install replacement coil.

10.Replace washer.

11. Check the o-rings (clean if necessary) on the hydraulic

brake unit or black adjustment knob.

12.Remount the hydraulic brake unit or black adjustment

knob. During mounting, take care not to damage the

o-rings on the shaft of the hydraulic brake on DMV-

DLE models and the adjustment knob on DMV-D

models.

13.Install and secure screws to the hydraulic brake unit or

black adjustment knob. Take care not to overtighten

14.With the gas pressure applied and valve #1 energized or

with both valve energized, perform an external leakage

test: Apply liquid leak detector around the gap between

the hydraulik brake unit or black adjustment knob, the

valve body and the solenoid.

15.If bubbles form, remove hydraulic brake unit or black

adjustment knob. Check and clean o-rings. (If o-rings

are damaged contact Karl Dungs, Inc. for a replacement

hydraulic brake or black adjustment cap.) Inspect the

bore in the cylinder shaft. Make sure it does not contain

any debris or burrs. Make sure no dirt can come into the

valve system. Remount the hydraulic brake unit or black

adjustment knob. Perform leakage test again. If the valve

still leaks contact Karl Dungs, Inc.

16.If no leak is detected, connect the DIN electrical connector.

17. Perform a complete function test: apply power to the valve,

make sure both valves open and close properly.

18.If the valve does not operate properly, contact Karl Dungs,

Inc. for technical help or replacement.

Karl Dungs GmbH & Co. KG

P.O. Box 12 29

D-73602 Schorndorf, Germany

Phone +49 (0)7181-804-0

Fax +49 (0)7181-804-166

e-mail info@dungs.com

Internet http://www.dungs.com

Karl Dungs, Inc.

3890 Pheasant Ridge Drive NE

Suite 150

Blaine, MN 55449, U.S.A.

Phone 763 582-1700

Fax 763 582-1799

e-mail info@karldungsusa.com

Internet http://www.dungs.com/usa/

Andere Dungs Steuereinheit Handbücher

Dungs

Dungs MultiBloc MBE-S Series Bedienungsanleitung

Dungs

Dungs VDK 200 A S02 Service-Handbuch

Dungs

Dungs GSV Series Bedienungsanleitung

Dungs

Dungs MB-ZR B07 Series Bedienungsanleitung

Dungs

Dungs DGAI. 20/5 Produkthandbuch

Dungs

Dungs VDK 200 Service-Handbuch

Dungs

Dungs DMK 5040 Service-Handbuch

Dungs

Dungs VPM-VC Bedienungsanleitung

Dungs

Dungs GasMultiBloc MBC-65 Series Bedienungsanleitung

Dungs

Dungs FRSBV Bedienungsanleitung

Dungs

Dungs DMV-D(LE) 704/6x4 Series Bedienungsanleitung

Dungs

Dungs DMV 11 eco Series Service-Handbuch

Dungs

Dungs MPA 5111 Bedienungsanleitung

Dungs

Dungs DGAI. 33F/2 Service-Handbuch

Dungs

Dungs VPS 504 Service-Handbuch

Dungs

Dungs SV-DLE 1005/604 Service-Handbuch

Dungs

Dungs VPM-VC Bedienungsanleitung

Dungs

Dungs HPSV 10020/604 Bedienungsanleitung

Dungs

Dungs DSLC px Vx Service-Handbuch

Dungs

Dungs GasMultiBloc MB-VEF B01 Bedienungsanleitung

Dungs

Dungs GasMultiBloc MB-D B07 Series Bedienungsanleitung

Dungs

Dungs VPM-VC Service-Handbuch

Dungs

Dungs MV X Produkthandbuch

Dungs

Dungs SAV 100065 MD Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung