Dunkirk ESC-3090S Gebrauchsanweisung

Dmkj'

MODELS

ESC-3090S

ESC-3090ST

ESC-4125S

ESC-4125ST

ESC-5185S

ESC-5185ST

ESC-6210S

ESC-6210ST

ESC IV STEAM SERIES 4

OIL-FIREDCASTIRON BOILER

INSTALLATION, OPERATION &

MAINTENANCE MANUAL

,,,,, .... ., ,uJq,ll_lllj_ pi_,

•"1,u,,,_,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

PATENT 7,823,544

/\_ /

_' M,E 1

Manufactured by:

ECR International, Inc.

2201 Dwyer Avenue. Utica NY 13501

web site: www.ecnnternat/onal.com P/N 240009804, Rev. A [10/2012]

Figure #1

35,3/4"

A,S,M,E

RELIEF PRESSURE

VALVE

ELWC[]

CYCLE GUARD

OIL BURNER

PRESSURE

ESC-3090 163/8'' 61/2'' 6"

ESC-4125 20¼" 81/2'' 6"

ESC-5185 23%" 101/2' 7"

ESC-6210 271/2'' 85/16'' 8"

Boiler model number on rating plate includes suffix 'S' or 'ST'.

STANDARD EOUIPMENT: Crated boiler, flush jacket, oil burner,

target wall/liner, safety valve, steam water level gauge, steam

pressure gauge, steam pressure control, low water cut-off, drain

valve, wiring harness, burner electric disconnect, plastic cover, 2"

supply tapping, 11/2'' return tapping, skim port, and primary control.

(NOTE: For tankless heater units, add tankless hot water coil, and

low limit control.)

Boiler Model 1 3 M n Natura Draft

. O,IBurnerInput() INetAHRIRat,ngs()l _:. _I

_umoer _mmney b_ze

Capacity A.RU.E.

WITHOUT WITH .... I ..... (2) MBH(4) ISteam ' Sq. Ft. I _ . I _ . Rating

TA.K'ESS,TANKLESS._'"" I 'v'°" I I MBH SteamI "°un°I _quareI

ESC-3090S ESC-309OST o.9o 126 106 80 333 6 8"x8"x15' 82.0

ESC-4125S ESC-4125ST 1.25 175 147 110 458 6 8"x8"x15' 82.0

ESC-5185S ESC-5185ST 1.85 259 216 162 675 8 8"x8"x15' 82.0

ESC-6210S ESC-6210ST 2.10 294 247 185 771 8 8"x8"x15' 82.0

NOTES:

1)Burner input is based on an oil heating value of 140,000 Btu/gal.

2)MBH = 1000 Btu per hour [Btu = British Thermal Unit].

3)Net AHRI Steam Ratings based on piping and pick-up allowance of 1.333. Consult manufacturer before selecting boiler for

installations having unusual piping and pick-up requirements, such as intermittent system operation, extensive piping, etc.

4)Electrical service is 120 Volts, 15 Amps, 60 Hz

iLine

ESC-3090ST 2 11

ESC-4125ST 4½ 13

ESC-5185ST 4½ 15

ESC-6210ST 4½ 17

Dimensions ........................................................ 2

Ratings, Data ..................................................... 3

Safety Symbols .................................................. 4

Locating The Boiler ............................................. 5

Ventilation And Combustion Air ............................ 6

Supply And Return Piping .................................... 8

Venting System Inspection & Installation ............. 12

Oil Tank And Piping ........................................... 13

Electrical Wiring ............................................... 14

Operating Instructions ....................................... 16

Maintenance Procedures .................................... 19

Service Checklist .............................................. 21

KEEP THIS MANUAL NEAR BOILER

RETAIN FOR FUTURE REFERENCE

IMPORTANT: Read and understand the following

instructions COMPLETELY before installing.

Installations of boilers and venting shall be done

only by qualified expert and in accordance with this

manual. Installing or venting a boiler or any other

gas appliance with improper methods or materials

could result in serious injury or death due to fire

or to asphyxiation from poisonous gases such as

carbon monoxide which is odorless and invisible.

Keep boiler area clear and free from combustible

materials, gasoline and other flammable vapors and

liquids.

Do not obstruct air openings to boiler room.

Modification, substitution or elimination of factory

equipped, supplied or specified components could

result in personal injury or the loss of life.

i_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!!iii__iiiiiiiiiiiiiiii_i!_!i_iii!:_ii!i!_ii!i!_i_!i_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!iiiii!iiiiiiiliiiiiii!i!i!ii!iliow.er InstaIIationandserviceofthisboilermust

be performed by a qualified installer.

The following defined symbols are used throughout this

manual to notify reader of potential hazards of varying risk

levels. Installer - Leave all instructions with the boiler for

future reference.

Indicates a hazardous situation which, if not

avoided, WILL result in death or serious injury.

When this product is installed in the Commonwealth

of Massachusetts the installation must be performed

by a Licensed Plumber or Licensed Gas Fitter.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

,i_ CAUTION

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

Indicates information which should be followed to

ensure proper installation and operation.

PATENT 7,823,544

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilUiLi_!_i_ii_!iiliNiii_ii!i!i!ii!ii!i_ii_iililEi!ii!ii!ii!il!!iili_il!_ii!_ii!ii_iii_ili_iiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiiiiiiiii_iiiiiiiiii

•Installations shall conform to the requirements of

the authority having jurisdiction. Such applicable

requirements take precedence over the general

instructions of this manual.

•Where required by the authority having jurisdiction,

the installation must conform to the American Society

of Mechanical Engineers Safety Code for Controls and

Safety Devices for Automatically Fired Boilers, ANSI/

ASME No. CSD-1.

•Locate boiler in front of final position before removing

crate.

•Provide level solid base as near chimney as possible

and centrally located with respect to heat distribution

system as practical.

•Allow 24 inches in front, top and right hand side for

servicing and cleaning, or removing tankless water

heating coil.

•Recommend 24 inches be allowed in back of boiler for

convenience when skimming hole is used.

•When installed in a utility room, the door should be

wide enough to allow largest boiler part to enter, or to

permit replacement of another appliance such as water

heater.

•Install boiler such that oil ignition system components

are protected from water (dripping, spraying, rain etc.)

during appliance operation and service.

Fire hazard. Do not install boiler on combustible

flooring or carpeting. Failure to follow these

instructions could result in death or serious injury.

FOR INSTALLATION ON NON-COMBUSTIBLE FLOORS ONLY

Boiler must not be installed on carpeting or vinyl flooring.

Minimum clearances to combustible construction are:

TOP 24 IN.

FRONT 24 IN.

FLUE CONNECTOR 9 IN.

REAR 24 IN.

LEFT SIDE 6 IN.

RIGHT SIDE 24IN.

NOTE:Clearance for accessshould exceedfire protection

clearance.

Figure #2 -Hinimum Clearances To Combustible

Construction (as seen from above)

BACK

FRONT

Asphyxiation, fire hazard. Do not obstruct air

openings to combustion area. Follow instructions

below, to maintain adequate combustion air.

126 26 126 32 63

175 35 175 44 88

259 52 259 65 130

294 59 294 74 147

* A space whose volume is not less than 50 cubic feet per 1000 BTU/Hour of all appliances installed in that space (cubic feet of

space = height x width x length)

** A space whose volume is less than 50 cubic feet per 1000 BTU/Hour of all appliances installed in that space (cubic feet of space

= height x width x length)

1. Ventilation of boiler room must be adequate enough to

provide sufficient air to properly support combustion,

venting and maintain safe ambient temperatures under

normal operating conditions.

2. When the boiler is located in an unconfined space in a

building of conventional construction frame, masonry

or metal, infiltration normally is adequate to provide

air for combustion and ventilation. However, in any

building which has been altered to conserve energy

or to minimize infiltration, the boiler area should

be considered as a confined space. If there is any

doubt, install air supply provisions for combustion

and ventilation in accordance with Chapter 5, Air for

Combustion and Ventilation, of NFPA 31, Standard

for the Installation of Oil Burning Equipment. The

recommendations that follow, or applicable provisions

of the local building codes.

3. When the boiler is installed in an unconfined space,

in a building of unusually tight construction, air for

combustion and room ventilation must be obtained

from outdoors or from spaces freely communicating

with the outdoors. A permanent opening or openings

having a total free area of not less than 1 square inch

per 5,000 BTU per hour of total input rating of all

appliances shall be provided. Ducts may be used to

convey make-up air from the outdoors and shall have

the same cross-sectional area of the openings to which

they are connected.

,When air for combustion and room ventilation is from

inside buildings, the confined space shall be provided

with two permanent openings, one starting 12 inches

from the top and one 12 inches from the bottom of the

enclosed space. Each opening shall have a minimum

free area of 1 square inch per 1,000 BTU per hour of

the total input rating of all appliances in the enclosed

space, but must not be less than 100 square inches.

These openings must freely communicate with the

interior areas having adequate infiltration from the

outside. See Figure #3.

Figure #3

f.. CHIMNEY

L TYPE VENT PIPE

BASEBOARD _h

When the boiler is installed in a confined space and

all air is provided from the outdoors, the confined

space shall be provided with two permanent openings,

one commencing within 12 inches from the top and

one commencing 12 inches from the bottom of the

enclosure. The openings shall communicate directly, or

by ducts, with the outdoors or spaces (crawl or attic)

that freely communicate with the outdoors. One of the

following methods must be used to provide adequate

air for ventilation and combustion.

A. When directly communicating with the outdoors,

each opening shall have a minimum free area of 1

square inch per 4,000 BTU per hour of total input

rating of all equipment in the enclosure. (Figure

#4)

B. When communicating with the outdoors by means

of vertical ducts, each opening shall have a

minimum free area Z square inch per 4,000 BTU

per hour of total input rating of all appliances in the

enclosed space. (Figure #5)

C. If horizontal ducts are used, each opening shall

have a minimum free area 1 square inch per 2,000

BTU per hour total input rating of all appliances in

the enclosed space. (Figure #6)

D. When ducts are used, they shall be of the same

cross sectional area as the free area of the area of

the openings to which they connect. The minimum

dimension of rectangular air ducts shall not be less

than 3 inches.

In calculating free area using louvers, grills or screens

for the above, consideration shall be given to their

blocking effect. Screens used shall not be smaller than

1/4 inch mesh. If the free area through a design of

louver or grill is known, it should be used in calculating

the size opening required to provide the free area

specified. If the design and free area is not known, it

may be assumed that wood louvers will have 20-25%

free area and metal louvers and grills will have 60-75%

free area. Louvers and grills shall be fixed in the open

position or interlocked with the boiler so that they are

opened automatically during boiler operation.

Figure #5

C iq I M_iNE Y

PI_PE

Burn or Scald Hazard. Discharge line shall be installed to safety valve outlet connection to avoid burns,

scalding, or water damage due to discharge of steam and/or hot water during operation.

Discharge line shall:

• Connect to safety valve outlet. Piped down to safe point of disposal. Check local codes for maximum

distance from floor or allowable safe point of discharge.

• Pipe size be of equal to or greater than of safety valve outlet over entire length of discharge line.

• Have no intervening shutoff valve between safety valve and discharge to atmosphere. Do not plug or

place any obstruction in discharge line.

• Terminate freely to atmosphere where any discharge will be clearly visible and at no risk of freezing.

• Allow complete drainage of valve and discharge line.

• Install safety valve with spindle in vertical position.

• Do not install shutoff valve between boiler and safety valve.

• Support safety valve discharge piping.

• Be short and straight as possible.

• Terminate with plain end, not threaded.

• Constructed of material suitable for exposure to temperatures of 375 ° F (191°C); or greater.

Refer to local codes and appropriate ASME Boiler and Pressure Vessel Code for additional installation

requirements.

Figure 4 -Safety Valve

SAFETY VALVE

DTSCHARGI

pTpTNG

Check local codes

for maximum

distance from

floor or other

allowable safe

point of discharge

6" Above Floor

1. Suggested piping for steam heating system can be

seen in Figure #7. Actual piping may vary based on

system design and local conditions.

Figure #7

NOTE: BOTH 2" SUPPLY TAPPINGS MUST

BE: USED, ALL NEAR BOILER SUPPLY HEADER

P_PING MUST BE A M_N|MUM OF 2". DO NOT

REDUCE,

OPTIONAL ONE OR TWO

TAKE°OFFS TO SYSTEM

HEADER

3 SECTION: 2 °

4 SECTION: 2A12"

5_ 6 7 SECTION: 3 '_

12" MIN

11/2" MINIMUM, IF RETURN

PIPING IS LARGER,

INCORPORATE SIZE TO EQUAL

THE RETURN PIPE SIZE,

SUPPLY

CONNECTION

SKiM TAPPING

ON SACK

OF BOILER

CLOSE NIPPLE

HARTFORD LOOP

CONNECTION

"RETURN MAIN

CLEANOUT TEE'S

FROM BOTTOM OF BOILER

See Figure #8 for typical piping for domestic hot water

heater.

• Automatic mixing valve must be installed on tankless

heater outlet. Install per valve manufacturer's

instructions.

• Install adjustable flow restrictor in cold water inlet

due to varying water conditions.

See Figures #9 and #10 for the suggested piping for

a modular steam boiler.

Water temperatures exceeding 125°F will cause

severe burns instantly or death by scalding.

Figure #8

PIPING FOR BUILT-IN

DOMESTIC HOT WATER HEATER

UNTEMPERED HOT WATER TO

__..._UTOM ATI C WASHER

UNTEMPERED _ TEMPERING VALVE

HOTWATER "-'_ _ INSTALLED BELOW CENTER

_ LINE OF BOILER HOT

IL; FI F

COLD WATER IN J

Dieses Handbuch passt für folgende Modelle

Andere Dunkirk Kessel Handbücher

Dunkirk

Dunkirk XEB-4 Gebrauchsanweisung

Dunkirk

Dunkirk Q95M-200 Gebrauchsanweisung

Dunkirk

Dunkirk Q90-50 Bedienungsanleitung

Dunkirk

Dunkirk EXCELSIOR EXB4075 Gebrauchsanweisung

Dunkirk

Dunkirk DCC-150 Gebrauchsanweisung

Dunkirk

Dunkirk DMG-240 Gebrauchsanweisung

Dunkirk

Dunkirk Q90-200 Gebrauchsanweisung

Dunkirk

Dunkirk DCB-100 Bedienungsanleitung

Dunkirk

Dunkirk PVWB Bedienungsanleitung

Dunkirk

Dunkirk Q90-50 Gebrauchsanweisung

Dunkirk

Dunkirk Q95M-200 Betriebsanleitung

Dunkirk

Dunkirk Empire II Bedienungsanleitung

Dunkirk

Dunkirk D247 Bedienungsanleitung

Dunkirk

Dunkirk Q90-125 Gebrauchsanweisung

Dunkirk

Dunkirk XEB-3 Gebrauchsanweisung

Dunkirk

Dunkirk EXCELSIOR Series Gebrauchsanweisung

Dunkirk

Dunkirk DCBF-125 Gebrauchsanweisung

Dunkirk

Dunkirk Helix VX-050 Gebrauchsanweisung

Dunkirk

Dunkirk DMG-380 Gebrauchsanweisung

Dunkirk

Dunkirk ESB0365 Technisches Dokument

Dunkirk

Dunkirk 90-50 Bedienungsanleitung

Dunkirk

Dunkirk GAS-FIRED BOILERS Bedienungsanleitung

Dunkirk

Dunkirk Q95M-200 Bedienungsanleitung

Dunkirk

Dunkirk EXCELSIOR Series Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung