Dunlop Billy Duffy Cry baby BD95 Bedienungsanleitung

92503019538REVA

THE ORIGINAL SINCE 1967.

92503019538REVB

BD95 BILLY DUFFY CRY BABY®

WAH

POWER

The Billy Duffy Cry Baby Wah can

be powered by one 9-volt battery

(accessed via the bottom of the pedal),

a 9-volt AC adapter such as the Dunlop

ECB003/ECB003EU, or the DC Brick™

and Iso-Brick™power supplies.

CONTROL DIAGRAMS

SETUP INSTRUCTIONS

• Run an instrument cable from your

guitar to the BD95’s INSTRUMENT

jack and another instrument cable from

the BD95’s AMPLIFIER jack to your

ampliﬁer’s input.

• To engage the effect, simply push the

toe of the pedal down with your foot.

To disengage, remove your foot from

the pedal.

• Use MODE kickswitch to toggle between

95Q mode, indicated by blue LEDs on

either side of pedal, and Vintage mode,

indicated by red LEDs.

• Rotate internal AUTO-RETURN DELAY

control clockwise to increase length of

effect ring out or counterclockwise to

decrease it.

• Rotate the VOLUME control clockwise to

increase volume of effect in 95Q mode

or counterclockwise to decrease it.

Note: This control is inactive in

Vintage mode.

• Rotate the Q control clockwise to

narrow 95Q mode’s bandpass and

emphasize higher end harmonics or

counterclockwise for a wider bandpass

that emphasizes lower end harmonics.

Note: This control is inactive in

Vintage mode.

• Rotate internal BLUE trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in Vintage mode.

• Rotate internal RED trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in 95Q mode.

• Rock your foot back and forth on the

pedal to hear the vocal, expressive tones

that the Cry Baby Wah is famous for.

CONTROLS

1. MODE kickswitch toggles between 95Q

mode (indicated by blue LEDs) and

Vintage mode (indicated by red LEDs)

2. VOLUME control sets 95Q mode’s

output level

3. Q control adjusts width of 95Q

mode’s bandpass

4. AUTO-RETURN DELAY control

(internal) sets how long effect rings

out after being disengaged

5. BLUE trimpot (internal) sets toe-down

range of 95Q mode

6. RED trimpot (internal) sets toe-down

range of Vintage mode

VOLUME control boosts

gain up to +15dB

Q control adjusts wah

frequency width

MODE switch toggles between

95Q & Vintage modes

LED LED

RED BLUE

SPECIFICATIONS

Impedance

Input 800 kΩ

Output < 1 kΩ

Noise Floor

Heel Down < -98 dBV

Toe Down < -90 dBV

Center Frequency fcRange*

95Q Mode 410 to 2,000 Hz

+20/-10%

Vintage Mode 450 to 2,200 Hz

+17/-10%

Max Gain at fc17 dB

Boost 0.1 to 15 dB

Bypass Buffered

Current Draw 8 mA

Power Supply DC 9 volts

*Center Frequency fcRange speciﬁcations are with the RED

and BLUE potentiometers fully clockwise.

• •

DUNLOP MANUFACTURING, INC.

P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

AUTO-RETURN

DELAY

BD95 BILLY DUFFY CRY BABY®

WAH

POWER

The Billy Duffy Cry Baby Wah can

be powered by one 9-volt battery

(accessed via the bottom of the pedal),

a 9-volt AC adapter such as the Dunlop

ECB003/ECB003EU, or the DC Brick™

and Iso-Brick™power supplies.

CONTROL DIAGRAMS

SETUP INSTRUCTIONS

• Run an instrument cable from your

guitar to the BD95’s INSTRUMENT

jack and another instrument cable from

the BD95’s AMPLIFIER jack to your

ampliﬁer’s input.

• To engage the effect, simply push the

toe of the pedal down with your foot.

To disengage, remove your foot from

the pedal.

• Use MODE kickswitch to toggle between

95Q mode, indicated by blue LEDs on

either side of pedal, and Vintage mode,

indicated by red LEDs.

• Rotate internal AUTO-RETURN DELAY

control clockwise to increase length of

effect ring out or counterclockwise to

decrease it.

• Rotate the VOLUME control clockwise to

increase volume of effect in 95Q mode

or counterclockwise to decrease it.

Note: This control is inactive in

Vintage mode.

• Rotate the Q control clockwise to

narrow 95Q mode’s bandpass and

emphasize higher end harmonics or

counterclockwise for a wider bandpass

that emphasizes lower end harmonics.

Note: This control is inactive in

Vintage mode.

• Rotate internal BLUE trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in Vintage mode.

• Rotate internal RED trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in 95Q mode.

• Rock your foot back and forth on the

pedal to hear the vocal, expressive tones

that the Cry Baby Wah is famous for.

CONTROLS

1. MODE kickswitch toggles between 95Q

mode (indicated by blue LEDs) and

Vintage mode (indicated by red LEDs)

2. VOLUME control sets 95Q mode’s

output level

3. Q control adjusts width of 95Q

mode’s bandpass

4. AUTO-RETURN DELAY control

(internal) sets how long effect rings

out after being disengaged

5. BLUE trimpot (internal) sets toe-down

range of 95Q mode

6. RED trimpot (internal) sets toe-down

range of Vintage mode

VOLUME control boosts

gain up to +15dB

Q control adjusts wah

frequency width

MODE switch toggles between

95Q & Vintage modes

LED LED

RED BLUE

SPECIFICATIONS

Impedance

Input 800 kΩ

Output < 1 kΩ

Noise Floor

Heel Down < -98 dBV

Toe Down < -90 dBV

Center Frequency fcRange*

95Q Mode 410 to 2,000 Hz

+20/-10%

Vintage Mode 450 to 2,200 Hz

+17/-10%

Max Gain at fc17 dB

Boost 0.1 to 15 dB

Bypass Buffered

Current Draw 8 mA

Power Supply DC 9 volts

*Center Frequency fcRange speciﬁcations are with the RED

and BLUE potentiometers fully clockwise.

• •

DUNLOP MANUFACTURING, INC.

P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

AUTO-RETURN

DELAY

BD95 BILLY DUFFY CRY BABY®

WAH

POWER

The Billy Duffy Cry Baby Wah can

be powered by one 9-volt battery

(accessed via the bottom of the pedal),

a 9-volt AC adapter such as the Dunlop

ECB003/ECB003EU, or the DC Brick™

and Iso-Brick™power supplies.

CONTROL DIAGRAMS

SETUP INSTRUCTIONS

• Run an instrument cable from your

guitar to the BD95’s INSTRUMENT

jack and another instrument cable from

the BD95’s AMPLIFIER jack to your

ampliﬁer’s input.

• To engage the effect, simply push the

toe of the pedal down with your foot.

To disengage, remove your foot from

the pedal.

• Use MODE kickswitch to toggle between

95Q mode, indicated by blue LEDs on

either side of pedal, and Vintage mode,

indicated by red LEDs.

• Rotate internal AUTO-RETURN DELAY

control clockwise to increase length of

effect ring out or counterclockwise to

decrease it.

• Rotate the VOLUME control clockwise to

increase volume of effect in 95Q mode

or counterclockwise to decrease it.

Note: This control is inactive in

Vintage mode.

• Rotate the Q control clockwise to

narrow 95Q mode’s bandpass and

emphasize higher end harmonics or

counterclockwise for a wider bandpass

that emphasizes lower end harmonics.

Note: This control is inactive in

Vintage mode.

• Rotate internal BLUE trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in Vintage mode.

• Rotate internal RED trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in 95Q mode.

• Rock your foot back and forth on the

pedal to hear the vocal, expressive tones

that the Cry Baby Wah is famous for.

CONTROLS

1. MODE kickswitch toggles between 95Q

mode (indicated by blue LEDs) and

Vintage mode (indicated by red LEDs)

2. VOLUME control sets 95Q mode’s

output level

3. Q control adjusts width of 95Q

mode’s bandpass

4. AUTO-RETURN DELAY control

(internal) sets how long effect rings

out after being disengaged

5. BLUE trimpot (internal) sets toe-down

range of 95Q mode

6. RED trimpot (internal) sets toe-down

range of Vintage mode

VOLUME control boosts

gain up to +15dB

Q control adjusts wah

frequency width

MODE switch toggles between

95Q & Vintage modes

LED LED

RED BLUE

SPECIFICATIONS

Impedance

Input 800 kΩ

Output < 1 kΩ

Noise Floor

Heel Down < -98 dBV

Toe Down < -90 dBV

Center Frequency fcRange*

95Q Mode 410 to 2,000 Hz

+20/-10%

Vintage Mode 450 to 2,200 Hz

+17/-10%

Max Gain at fc17 dB

Boost 0.1 to 15 dB

Bypass Buffered

Current Draw 8 mA

Power Supply DC 9 volts

*Center Frequency fcRange speciﬁcations are with the RED

and BLUE potentiometers fully clockwise.

• •

DUNLOP MANUFACTURING, INC.

P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

AUTO-RETURN

DELAY

BD95 BILLY DUFFY CRY BABY®

WAH

POWER

The Billy Duffy Cry Baby Wah can

be powered by one 9-volt battery

(accessed via the bottom of the pedal),

a 9-volt AC adapter such as the Dunlop

ECB003/ECB003EU, or the DC Brick™

and Iso-Brick™power supplies.

CONTROL DIAGRAMS

SETUP INSTRUCTIONS

• Run an instrument cable from your

guitar to the BD95’s INSTRUMENT

jack and another instrument cable from

the BD95’s AMPLIFIER jack to your

ampliﬁer’s input.

• To engage the effect, simply push the

toe of the pedal down with your foot.

To disengage, remove your foot from

the pedal.

• Use MODE kickswitch to toggle between

95Q mode, indicated by blue LEDs on

either side of pedal, and Vintage mode,

indicated by red LEDs.

• Rotate internal AUTO-RETURN DELAY

control clockwise to increase length of

effect ring out or counterclockwise to

decrease it.

• Rotate the VOLUME control clockwise to

increase volume of effect in 95Q mode

or counterclockwise to decrease it.

Note: This control is inactive in

Vintage mode.

• Rotate the Q control clockwise to

narrow 95Q mode’s bandpass and

emphasize higher end harmonics or

counterclockwise for a wider bandpass

that emphasizes lower end harmonics.

Note: This control is inactive in

Vintage mode.

• Rotate internal BLUE trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in Vintage mode.

• Rotate internal RED trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in 95Q mode.

• Rock your foot back and forth on the

pedal to hear the vocal, expressive tones

that the Cry Baby Wah is famous for.

CONTROLS

1. MODE kickswitch toggles between 95Q

mode (indicated by blue LEDs) and

Vintage mode (indicated by red LEDs)

2. VOLUME control sets 95Q mode’s

output level

3. Q control adjusts width of 95Q

mode’s bandpass

4. AUTO-RETURN DELAY control

(internal) sets how long effect rings

out after being disengaged

5. BLUE trimpot (internal) sets toe-down

range of 95Q mode

6. RED trimpot (internal) sets toe-down

range of Vintage mode

VOLUME control boosts

gain up to +15dB

Q control adjusts wah

frequency width

MODE switch toggles between

95Q & Vintage modes

LED LED

RED BLUE

SPECIFICATIONS

Impedance

Input 800 kΩ

Output < 1 kΩ

Noise Floor

Heel Down < -98 dBV

Toe Down < -90 dBV

Center Frequency fcRange*

95Q Mode 410 to 2,000 Hz

+20/-10%

Vintage Mode 450 to 2,200 Hz

+17/-10%

Max Gain at fc17 dB

Boost 0.1 to 15 dB

Bypass Buffered

Current Draw 8 mA

Power Supply DC 9 volts

*Center Frequency fcRange speciﬁcations are with the RED

and BLUE potentiometers fully clockwise.

• •

DUNLOP MANUFACTURING, INC.

P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

AUTO-RETURN

DELAY

BD95 BILLY DUFFY CRY BABY®

WAH

POWER

The Billy Duffy Cry Baby Wah can

be powered by one 9-volt battery

(accessed via the bottom of the pedal),

a 9-volt AC adapter such as the Dunlop

ECB003/ECB003EU, or the DC Brick™

and Iso-Brick™power supplies.

CONTROL DIAGRAMS

SETUP INSTRUCTIONS

• Run an instrument cable from your

guitar to the BD95’s INSTRUMENT

jack and another instrument cable from

the BD95’s AMPLIFIER jack to your

ampliﬁer’s input.

• To engage the effect, simply push the

toe of the pedal down with your foot.

To disengage, remove your foot from

the pedal.

• Use MODE kickswitch to toggle between

95Q mode, indicated by blue LEDs on

either side of pedal, and Vintage mode,

indicated by red LEDs.

• Rotate internal AUTO-RETURN DELAY

control clockwise to increase length of

effect ring out or counterclockwise to

decrease it.

• Rotate the VOLUME control clockwise to

increase volume of effect in 95Q mode

or counterclockwise to decrease it.

Note: This control is inactive in

Vintage mode.

• Rotate the Q control clockwise to

narrow 95Q mode’s bandpass and

emphasize higher end harmonics or

counterclockwise for a wider bandpass

that emphasizes lower end harmonics.

Note: This control is inactive in

Vintage mode.

• Rotate internal BLUE trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in Vintage mode.

• Rotate internal RED trimpot clockwise

for a brighter toe-down response or

counterclockwise for a warmer toe-down

response. Note: This control is inactive

in 95Q mode.

• Rock your foot back and forth on the

pedal to hear the vocal, expressive tones

that the Cry Baby Wah is famous for.

CONTROLS

1. MODE kickswitch toggles between 95Q

mode (indicated by blue LEDs) and

Vintage mode (indicated by red LEDs)

2. VOLUME control sets 95Q mode’s

output level

3. Q control adjusts width of 95Q

mode’s bandpass

4. AUTO-RETURN DELAY control

(internal) sets how long effect rings

out after being disengaged

5. BLUE trimpot (internal) sets toe-down

range of 95Q mode

6. RED trimpot (internal) sets toe-down

range of Vintage mode

VOLUME control boosts

gain up to +15dB

Q control adjusts wah

frequency width

MODE switch toggles between

95Q & Vintage modes

LED LED

RED BLUE

SPECIFICATIONS

Impedance

Input 800 kΩ

Output < 1 kΩ

Noise Floor

Heel Down < -98 dBV

Toe Down < -90 dBV

Center Frequency fcRange*

95Q Mode 410 to 2,000 Hz

+20/-10%

Vintage Mode 450 to 2,200 Hz

+17/-10%

Max Gain at fc17 dB

Boost 0.1 to 15 dB

Bypass Buffered

Current Draw 8 mA

Power Supply DC 9 volts

*Center Frequency fcRange speciﬁcations are with the RED

and BLUE potentiometers fully clockwise.

• •

DUNLOP MANUFACTURING, INC.

P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658

AUTO-RETURN

DELAY

Andere Handbücher für Billy Duffy Cry baby BD95

Inhaltsverzeichnis

Andere Dunlop Musikpedal Handbücher

Dunlop

Dunlop EJF1 ERIC JOHNSON SIGNATURE FUZZ FACE Bedienungsanleitung

Dunlop

Dunlop Authentic Hendrix 68 Shrine Series Bedienungsanleitung

Dunlop

Dunlop Cry baby Classic Bedienungsanleitung

Dunlop

Dunlop GEEZER CRY BABY GZR95 WAH Handbuch

Dunlop

Dunlop CBM95 Cry Baby Mini Wah Bedienungsanleitung

Dunlop

Dunlop Fuzz Face JHM1 Bedienungsanleitung

Dunlop

Dunlop CRY BABY MINI 535Q WAH Bedienungsanleitung

Dunlop

Dunlop GCB95Original Cry Baby Bedienungsanleitung

Dunlop

Dunlop VOLUME (XL) Bedienungsanleitung

Dunlop

Dunlop GCB95F Cry Baby Bedienungsanleitung

Dunlop

Dunlop FUZZFACE FFM2 MINI Bedienungsanleitung

Dunlop

Dunlop AUTHENTIC HENDRIX 69 PSYCH SERIES OCTAVIO... Bedienungsanleitung

Dunlop

Dunlop MXR PHASE 95 Bedienungsanleitung

Dunlop

Dunlop VOLUME (X)8 Bedienungsanleitung

Dunlop

Dunlop EVH117 Bedienungsanleitung

Dunlop

Dunlop CRY BABY Q ZONE QZ1 Bedienungsanleitung

Dunlop

Dunlop CRY BABY WULDE WAH ZW-45 Bedienungsanleitung

Dunlop

Dunlop MXR M109 Bedienungsanleitung

Dunlop

Dunlop FUZZ FACE FFM1 Bedienungsanleitung

Dunlop

Dunlop MXR M236 SUPER BADASS Bedienungsanleitung

Dunlop

Dunlop MXR Phase 90 Bedienungsanleitung

Dunlop

Dunlop 105Q BASS WAH Bedienungsanleitung

Dunlop

Dunlop BFG07 Bedienungsanleitung

Dunlop

Dunlop Authentic Hendrix 68 Shrine Series Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung

TREX

TREX ToneBug Totenschläger Bedienungsanleitung

BBE

BBE ORANGE SQUASH Bedienungsanleitung

Tube Works

Tube Works 310 Bedienungsanleitung