Duratech PL-REM Bedienungsanleitung
PL-REM
Manual
English....................Page 2
Nederlands.......Pagina 12
Français...............Page 22
Deutsch...............Seite 32
LINK Driver
2
Table of contents
Technical specifications
Box contents
Installation instructions
Pairing Handheld Transmitter & controller
Handheld transmitter functions
Replacing transmitter battery
Change relay A/B mode
Troubleshooting
Page 3
Page 4
Page 5-6
Page 7
Page 8
Page 8
Page 9
Page 10
3
ENG
Technical specifications
Electrical specifications
General specifications Controller
Ambient air temperature
Humidity
Dimensions
Weight
Ingress protection rate
0°C ... +40°C
10% ... 90% RH
non condensing
150x157x51 mm
500 g
IP54
Nominal Input voltage
Max rating Relay Contacts
“Color&Light”, “A” and “B”
Resistive Load
Inductive Load
Frequency band transmitter
IEC Protection Class
230 VAC 50 Hz
14A 250VAC
14A 30VDC
6A 250VAC
6A 30VDC
868 MHz
Class II
For operation only with 12VAC safety isolation transformer
to power Spectravision®LED Pool Lights
4
Box contents
12
45
1. PL-REM controller
2. Handheld transmitter (DuraLink™ version)
3. Spare battery (type A23 12V)
4. Screws (4x) & wall plugs (4x)
5. Owners’s manual
3
5
ENG
Installation instructions
230VAC
Garden lights
Pool cover
230VAC 230VAC
12VAC
Option 1: PL-REM in transformer primary
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal
• Connect the primary circuit of a 12VAC transformer (sold sepa-
rately) in series with the “Color&Light” terminal of the PL-REM.
The “Color&Light” relay contact has an output of 14A, which can
drive a 12V transformer of max. 3000W (220Vx14A).
Optional: The “Switch A” & “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.
6
Option 2: PL-REM in transformer secondary
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal
• Connect the secondary circuit of a 12VAC transformer (sold sepa-
rately) in series with the “Color&Light” terminal of the PL-REM.
The “Color&Light” relay contact has an output of 14A, or 170W on a 12V
transformer secondary (14Ax12V). The total load of pool lights can not
exceed this.
Optional: The “Switch A” & “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.
230VAC
Garden lights
Pool cover
230VAC 230VAC
12VAC
7
ENG
Pairing handheld transmitter & controller
The handheld transmitter is already paired in the factory and ready to
use. The PL-REM can pair with up to 6 handheld transmitters. In case a
problem arises, the pairing process can be done manually:
Manual Pairing process:
Make sure the PL-REM is connected to a power source.
1. Press the pairing button on the small circuit board, inside the con-
troller for at least 5 seconds.
--> The LED will start to blink fast
2. Within 25 seconds, press any button on the handheld transmitter.
--> If the transmitter is paired correctly, the LED will flash slowly for 5 times
--> If the PL-REM pairing memory is full, the LED will flash 15 times.
This means 6 handheld devices have already been paired.
To unpair all handheld transmitters with the controller: Push the pair-
ing button for at least 5 seconds, then do nothing for at least 25 sec-
onds.
--> The pair memory will be erased - the red LED will flash 5x on/o.
Red LED
Pairing button
8
Handheld transmitter functions
Toggle the lamps ON/OFF
Go to next color scenario
Toggle Output A ON/OFF
Toggle Output B ON/OFF
Replacing transmitter battery
+
-
• Remove the philips head screw and open the transmitter
• Replace the battery, respecting the polarity
Battery type: A23 12V
9
ENG
The relays A & B can be used to control auxiliary circuits like garden
lighting or a pool cover.
The operation mode of these relays can be modified:
Option 1: Normal open/closed contact
Option 2: Pulsed contact
Modification process:
1. Locate the 5 pinholes on the circuit board
2. Make a connection between pin 1 and 2
(use a piece of wire, or a paperclip)
3. Power ON the device by connecting a 230VAC power source
to the 220-240VAC INPUT terminal
4. Power OFF the device
5. Remove the connection between pin 1 and 2
Every time the above process is repeated, the A & B relays switch
between Normal open/closed mode and Pulsed operation mode
Pin 1 Pin 2
Change Relay A/B mode
10
PROBLEM SOLUTION
The controller doesn’t react
to transmitter commands
• Check the battery of the hand-
held transmitter
• The transmitter is not paired-
correctly with the controller.
Repeat the pairing process
• Reduce the distance between
handheld transmitter and PL-
REM and/or remove obstacles
The pool lights don’t work • Check if all connections are
made according to the electri-
cal scheme on page 5 or 6.
• Check if the “Color&Light” out-
put terminals of the controller
switch on and of when pushing
the on/o button on the trans-
mitter.
Troubleshooting
Inhaltsverzeichnis
Sprachen:
Andere Duratech Gleichstromantrieb Handbücher
Beliebte Gleichstromantrieb Handbücher anderer Marken
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Stücklistenhandbuch
Chamberlain Garog
Chamberlain Garog D Series Bedienungsanleitung
Parker
Parker PDS Series Bedienungsanleitung
Festo
Festo DGC G Series Einrichtungshandbuch
Binks
Binks QS-5012-1-CE Bedienungsanleitung
