Duratool D03293 Bedienungsanleitung
1
Foam Cutter Kit
Model: D03293
2
IMPORTANT SAFETY INFORMATION
WHAT’S INCLUDED
Please read these instructions carefully before use and retain for future reference
• When using electrical appliances basic safety precautions should always be
followed.
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the power adapter to the mains power supply.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children unless they are older than 8 and supervised.
• Do not operate the appliance with a damaged plug or cord, after a malfunction or
after being dropped or damaged in any way.
• If the supply cord is damaged, it must be replaced by a qualied engineer in order
to avoid injury or a hazard.
• Ensure there is sufcient space and ventilation around the appliance to allow the
escape of heat and/or fumes.
• Do not touch the cutting parts until cooled to room temperature.
• Do not expose to rain or moisture.
• Never place the product or part of it in water, or operate if your hands are wet.
• The tool must not be left unattended while it is powered on.
• Turn the tool off and unplug the power supply when it is not in use.
APPLICATION & OPERATION
• Cutting tool
• Stand
• 1 additional cutting tip and 1 additional engraving tip
• Mains PSU
• User manual
Note: The rst time you use the cutter, it may smoke slightly before use as the heating
element dries out. This is normal and should only last for a few minutes.
3
TOOL REPLACEMENT
• Replacing the cutting tip should only be done when the tool is switched off and at
room temperature.
• It is imperative that the tool is switched off, unplugged and allowed to cool before
and after cutter replacement.
• Caution: Damage could occur if the tool is left on without the cutter attached.
Warning: Care should be taken to avoid burns.
• Attach the tip required for the cutting operation required.
• Connect the cutting tool to the supplied PSU and plug the PSU into a mains power
socket.
• Switch the in-line power switch to the ON position and the cutter will start to heat
up. The cutter is ready for use in around 10 seconds.
• Always rest to cutter on the stand when not in use.
• Avoid breathing any fumes or smoke given off by the material being worked. It is
advisable to wear a face mask when cutting foam.
CLEANING
SPECIFICATION
• Cleaning should only be done when the iron is switched off and at room
temperature.
• The iron may be cleaned with a damp cloth and a small amount of liquid detergent
if necessary.
• Never submerse the soldering iron in liquid or allow any liquid to enter the case.
• Do not use any chemicals, abrasives or solvents that could damage the soldering
iron.
Voltage 220-240V~50Hz
Power 8W
Power adaptor output 5V DC 1500mA
4
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area. Made in China. PR2 9PP
Man Rev 1.0
Inhaltsverzeichnis
Andere Duratool Cutter Handbücher
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
