Duratool D03046 Bedienungsanleitung

DIGITAL MULTIMETER

Model: D03046 and D03047

IMPORTANT SAFETY INFORMATION

Please read these instructions carefully before use and retain for future reference.

• Check the test leads, probes and case insulation before using. If you nd any

breakage or abnormality, or you consider the device is broken, stop using the

device immediately.

• When using the test probes, keep your ngers behind the nger protection

ring.

• Do not use the meter with the back cover open.

• Select appropriate test range for measurements.

• Ensure all inputs are less than the range selected otherwise it may cause

electrical shock or meter damage.

• Do not change the range selector position during voltage or current

measurements.

• Do not apply a voltage exceeding the marked voltage between COM terminal

and ground.

• Take caution when working voltages are above 60V DC or 30V AC rms.

• Do not connect the meter to voltage signals when the range selector is on

current, resistance, diode or continuity range.

• When measuring current, each single measurement should be shorter than 10

seconds.

• When a measurement has been completed, disconnect the testing probes

from the circuit under test.

• Replace the batteries as soon as the low battery indicator appears on the

display.

• Remove dead batteries from the meter or if it is not going to be used for a long

time.

• Never mix old and new batteries together, or different types of batteries.

• Never dispose of batteries in a re, or attempt to recharge ordinary batteries.

• Before replacing the battery, turn off the meter and disconnect all the test

probes.

• To prolong battery life turn off the meter after use.

FUNCTIONS

Model DCV ACV DCA ΩhFE

D03046 PPPPP P

D03047 PPPPPPPP

DC VOLTAGE

LCD

Rotary

Range

Selector

5A Jack

VΩmA Jack

COM Jack

hFE Socket

Range Resolution Accuracy

200mV 100µV ±(0.5% of rdg +3D)

2000mV 1mV

±(0.8% of rdg +5D)20V 10mV

200V 100mV

500V 1V ±(1.0% of rdg +5D)

• OVERLOAD PROTECTION: 220V rms AC for 200mV range and 500V DC or

500V rms for all ranges.

AC VOLTAGE

CONTINUITY

DC CURRENT

Range Resolution Accuracy

200V 100mV

±(2.0% of rdg +10D)

500V 1V

Range Description

Built in buzzer sounds if resistance is less

than 30±20Ω

• RESPONSE: Average responding, calibrated in rms of a sine wave.

• FREQUENCY RANGE: 45Hz ~ 450Hz.

• OVERLOAD PROTECTION: 500V DC or 500V rms for all ranges.

• OVERLOAD PROTECTION: 15 seconds maximum 220V RMS.

• OVERLOAD PROTECTION: F0.5A/500V and F5A/250V fuse.

• MEASURING VOLTAGE DROP: 200mV.

Range Resolution Accuracy

200µA 100nA

±(1.8% of rdg +2D)

2000µA 1µA

20mA 10µA

200mA 100µA ±(2.0% of rdg +2D)

5A 10mA ±(2.0% of rdg +10D)

RESISTANCE

OPERATION

• MAXIMUM OPEN CIRCUIT VOLTAGE: 3V.

• OVERLOAD PROTECTION: 15 seconds maxi- mum 220Vrms.

Range Resolution Accuracy

200Ω0.1Ω±(1.0% of rdg +10D)

2000Ω1Ω

±(1.0% of rdg +4D)

20kΩ10kΩ

200kΩ100kΩ

2000kΩ1kΩ

DC & AC VOLTAGE MEASUREMENT

• Connect red test lead to “VΩmA” jack, Black lead to “COM” jack.

• Set RANGE switch to desired VOLTAGE position, if the voltage to be

measured is not known beforehand, set switch to the highest range and

reduce it until satisfactory reading is obtained.

• Connect test leads to device or circuit being measured.

• Turn on power of the device or circuit being measured voltage value will

appear on Digital Display along with the voltage polarity.

DC CURRENT MEASUREMENT

• Red lead to “VΩmA”. Black lead to “COM” (for measurements between 200mA

and 5A connect red lead to “5A” jack with fully depressed).

• Set RANGE switches to desired DCA position.

• Open the circuit to be measured, and connect test leads IN SERIES with the

load in with current is to measure.

• Read current value on Digital Display.

• Additionally, “5A” function is designed for intermittent use only. Maximum

contact time of the test leads with the circuit is 10 seconds, with a minimum

intermission time of 15 minutes between tests.

RESISTANCE MEASUREMENT

• Red lead to “VΩmA”. Black lead to “COM”.

• Set RANGE switch to desired Ω position.

• If the resistance being measured is connected to a circuit, turn off power and

discharge all capacitors before measurement.

• Connect test leads to circuit being measured.

• Read resistance value on the display.

DIODE MEASUREMENT

• Red lead to “VΩmA”, Black lead to “COM”.

• Set RANGE switch to “ ” position.

• Connect the red test lead to the anode of the diode to be measured and black

test lead to cathode.

• The forward voltage drop in mV will be displayed. If the diode is reversed,

gure “1” will be shown.

TRANSISTOR hFE MEASUREMENT

• Set RANGE switch to the hFE position.

• Determine whether the transistor is PNP of NPN type and locate the Emitter,

Base and Collector leads. Insert the leads into the correct pins of the hFE

socket.

• The meter will display the approximate hFE value at the condition of base

current 10μA and VCE2.8V.

AUDIBLE CONTINUITY TEST

• Red lead to “VΩmA”, Black lead to “COM”.

• RANGE switch to “ ” position.

• Connect test leads to two points of circuit to be tested. If the resistance is

lower than 30Ω ± 20Ω, the buzzer will sound.

TEST SIGNAL

• Set RANGE switch to “ ” position.

• A test signal (50Hz) is produced between “VΩmA” and “COM” jack.

• The output voltage is approx 5V p-p with 50KΩ impedance.

NOTE: OVERLOAD PROTECTION: 15 seconds maximum 220Vrms.

BATTERY REPLACEMENT

CLEANING

SPECIFICATIONS

• If “ ” appears in display, it indicates that the battery should be replaced.

• To replace battery remove the meter from the protective surround, then

remove the 2 screws in the rear of the case

• Remove the rear case half and simply remove the old battery, and replace with

a new one. (9-volt battery, NEDA 1604 6F22 type)

• Be careful to observe correct polarity.

• Fuses rarely need replacement and blow almost always as a result of operator

error. (F500mA/500V for mA terminal and F5A/500V for 5A terminal).

• Clean the meter with a clean, soft cloth.

• Do not use any chemicals, abrasives or solvents that could damage the meter.

Max display: LCD 3½ digits (1999 count) 0.5” high

Polarity: Automatic, indicated minus, assumed plus.

Measure method: Double integral A/D switch implement

Sampling speed: 2 times per second

Over-load indication: “1” is displayed

Operating Environment: 0o~40o, at <80%RH

Storage Environment: -10o~50o, at <85%RH

Power: 9V NEDA 1604 or 6F22

Low battery indication: “ ”

Static electricity: Approx 4mA

Dimension: 126 x 70 x 26mm

Weight: 108g (including battery)

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL

& ELECTRONIC EQUIPMENT.

When this product has reached the end of its life it must be treated as Waste Electrical &

Electronics Equipment (WEEE). Any WEEE marked products must not be mixed with general

household waste, but kept separate for the treatment, recovery and recycling of the materials

used. Contact your local authority for details of recycling schemes in your area.

Made in China. PR2 9PP

Man Rev 1.0

Andere Handbücher für D03046

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Duratool Multimeter Handbücher

Duratool

Duratool D03124 Bedienungsanleitung

Duratool

Duratool D03305 Bedienungsanleitung

Duratool

Duratool D03046 Montageanleitung

Duratool

Duratool D03143 Bedienungsanleitung

Duratool

Duratool D03127 Bedienungsanleitung

Duratool

Duratool D03125 Bedienungsanleitung

Duratool

Duratool D03126 Bedienungsanleitung

Duratool

Duratool D03145 Bedienungsanleitung

Duratool

Duratool D03124 Bedienungsanleitung

Duratool

Duratool D03131 Bedienungsanleitung

Duratool

Duratool D03122 Bedienungsanleitung

Duratool

Duratool D03143 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung