DutchWest 2181 (Small) Bedienungsanleitung

SERVICE MANUAL

For the

Vermont Castings

Please place picture here.

1990 - 1993 D

CONVECTION

UTCHWEST

HEATERS

ODELS:

ll)

arge)

2181 (Sma

2183 (Large)

2184 (Extra L

HISTORY OF CHANGES

1990 – 1993 DUTCHWEST CONVECTION HEATERS

Models 2181 (Small), 2183 (Large), and 2184 (Extra Large)

In 1990, Vermont Castings changed the Dutchwest Convection Heaters to improve the

appearance, performance and serviceability of the stoves. The changes include:

•A horizontal brass bar in a convection outlet slot where the top and front meet. This

replaces the earlier two separate screened openings.

•Convection air inlets on the bottom of the stove. These become invisible to the user, and

replace earlier screened openings on the stove front.

•A modified damper linkage using a ductile-iron ‘crank-shaft’ passing through an adjustable

‘stirrup’ lifter.

•A ceramic fiber insulator around the combustor.

•A larger cook top. It is no longer a separate polished part but part of the stove top. A rope

gasket is used on the under side of the stove top for quick and easy access to the combustor

and damper.

•A heavier catalyst baffle. It is now heavier, and round, and made of ductile-iron, and has a

Sequoia-style round air distributor between it and the catalyst.

•Coal grate sides and front are now optional and the fire screen is optional.

•Latches are helical on un-threaded steel stems.

•An ‘air balance plate’ at the right end of the firebox. This brings room air into the firebox, to

balance the effect of the primary air inlet on the side-load door.

•An air diffuser plate on the inside of the side-load door. This slows the flow of the air into

the firebox.

•A round flue collar on the small and large units. The extra-large uses the Encore 8” oval

flue collar.

•Heat-reflective coating on the glass panels. This helps them stay clearer. For the extra-

large, there are left and right panels. Glass became standard equipment in 1992.

•Dropped the earlier steel gasket caps for the rocker grates, and substituted a single a cast-

iron panel to form the seal on the left side.

In 1992, Vermont Castings changed the inner tops to include a separate ‘web’ piece between the

damper and the catalyst. Since the web is separate from the main inner top, it can ‘float’ in

response to the high temperatures in that area.

Instructions for installing the new two piece inner top are found in the Repair Procedures Section.

REPAIR PROCEDURES

1990 – 1993 DUTCHWEST CONVECTION HEATERS

Models 2181 (Small), 2183 (Large), and 2184 (Extra Large)

INSTALLING THE TWO PIECE INNER TOP

Tools Required: Phillips and flat screwdrivers, socket wrench with 7/16” socket/open-end wrench,

rubber mallet, and 3 tubes of stove cement, caulking gun, putty knife, rags, hammer, cold chisel,

and wooden block.

1. Remove the top (one bolt in each corner). Since there is a gasketed seam between inner and

outer tops, you won’t need to break a cement seal here.

2. Remove the refractory insulator and combustor.

3. Remove the anchor bolt holding the #29 damper adjuster to the #28 damper. There is a hex

nut on the anchor bolt on the under side of the damper.

4. Rotate #35 damper crank counter-clockwise (as you face left side of the stove) until it

separates from the #36 damper operating rod. Lift the damper and operating crank off along

with adjuster.

5. Lift the front doors (including ash door) and brass bar #60 off the stove front.

6. Remove 2 hex nuts from the studs joining the stove front to the stove sides, above the inner

top.

7. Use a hammer and a wooden block to tap outward on the stove front from inside the firebox.

Once the cement seal is broken, lift the front off and set it aside. If you have left the ash door

on the stove front, do not set the front down vertically--pressure on the ash door can break it or

the stove front.

8. Remove the hex nut and washer from the stud above the right rear corner of the inner top

(joining the right side and the outer back). From inside, tap outward against the right side to

break its cement seal. Pull the right outward and forward at the same time until it clears the

inner back and then lift it off.

9. Tap around the left and rear edges of the inner top to separate it from the inner back and the

left side, and lift it out.

10. Use hammer and cold chisel to clean old cement out of the joints of all parts to be re-used.

11. Work in reverse order to re-assemble. Replacement inner tops include a separate ‘web’ piece

between the catalyst chamber and the damper opening. This web can move separately in

response to the high temperatures in that area.

The web is loosely bolted into place at each end and has Interam gasket to seal its ends. On

installation, the Interam gasket can look too small for the gap it seals. However, this Interam

will expand greatly under heat, and seal the gaps.

It’s worthwhile to do a ‘dry fit’ to ensure that parts fit together well before you cement anything.

Put a heavy bead of stove cement in each joint groove before putting the mating piece of iron

into it. When installing the inner top, be sure to align the inner top with the bypass operating

rod’s hole in the left side so that the bypass gate operates freely without causing the operating

rod to be forced to one side of the hole in the stove’s left side. Adjust the bypass gate so it

closes with only a little pressure.

12. Transfer the original baffle, channel cap, and air distributor from the original inner top to the

new one.

13. When the inner top is in place and the right side is attached and supports the inner top, use

hex bolts and steel tabs to attach the damper to the inner top. After you have positioned the

damper crank, damper operating rod, and adjuster--anchor the adjuster to the damper with a

hex bolt and nut below the damper.

14. Re-attach the stove front, after cementing its seams where it joins the stove sides and the

inner top and the inner bottom. Add the doors.

15. Install the catalytic combustor and insulator. Be sure there is Interam gasket around the

combustor.

16. Re-install the brass bar across the top/front opening.

17. Check the gasketing on the under side of the stove top to ensure a good seal here. Replace

the top. The bolts should be snug but not overly tight; over-tightening can warp the top,

possibly causing leakage.

18. Direct the customer to re-‘cure’ the stove, to acclimate the new inner top to the pressures of

expansion and contraction. Curing is a series of five small fires, with each fire hotter and

longer than the previous one.

INSTALLING THE SHAKER CENTRE GRATE

The shaker centre grate is easy to install in your stove. It should take about ten minutes to replace

it.

Start by removing the grate back and the side half-wall (called ‘air balance plate’ on some models).

Each panel has two bolts holding it in place.

Lift the rear edge of the grate frame (called ‘grate’ in some instructions) and prop it up out of the

way. Now you can lift out the centre grate through the front door and the centre opening of the

frame. There is no hardware holding the centre grate; it sits on ‘saddles’ on the stove’s inner

bottom. Replace the shaker centre grate, putting the edge with the longer teeth toward the front of

the stove. The longer teeth point downward. These prevent coal embers from falling into the pan,

unless you intentionally rock the rockers more than 60 degrees. When you lower the grate frame

back into position, be sure the rockers are level, so that they will rotate properly when everything is

back in place. Then bolt the grate back and the side half wall onto the back and side of the firebox,

and you’re done. Be sure to build your next fire slowly, so that the new iron will ‘cure’ properly.

ADJUSTING THE DAMPER

Using a 7/16 socket wrench, preferably with a socket extension:

1. Remove the top.

2. Open the damper.

3. Carefully remove the refractory cover.

4. Loosen the adjusting bolt’s lock nut.

5. Loosen the anchor bolt’s lock nut, located on the underside of the damper and accessible

inside the stove through the front door.

6. Loosen the anchor bolt a turn or two.

7. Tighten the adjusting bolt.

8. Test the damper mechanism. If further adjusting is necessary, continue to tighten the adjusting

bolt until the damper closes snugly.

9. When final adjustment has been made, tighten the adjusting bolt lock nut.

10. Tighten the anchor bolt. Tighten the anchor bolt lock nut.

DISASSEMBLY and ASSEMBLY

1990 – 1993 DUTCHWEST CONVECTION HEATERS

Models 2181 (Small), 2183 (Large), and 2184 (Extra Large)

DISASSEMBLY

Clear a space for storing parts as you take the stove apart.

You will need pliers, a 7/16” socket wrench or open end wrench, a 5/32” Allen wrench and a

Phillips head screwdriver to remove nuts and bolts and screws. You will need a dead blow

hammer to dislodge parts which have been cemented together. A conventional, steel hammer and

block of wood may be used in place of the dead blow hammer. Use the block of wood to protect

the metal parts from direct blows of the steel hammer.

These directions will tell you what screws or nuts should be removed during the disassembly of

your stove. Some hex head screws in the top and sides are for the installation of optional

accessories. Do not remove these screws unless directed to do so in the instructions for

installation of the accessories.

**NOTE: Wear gloves and protective eye wear.

Instructions are given as you face the stove.

You may wish to pull out, empty and clean the ash pan, and use it to hold hardware you remove

from the stove.

1. Lift the Probe Thermometer from the Top.

2. Lift the Front Doors from the Stove.

3. Lift the Load Door from the Stove.

4. Remove the Top.

Use a 7/16” wrench to remove the four hex head cap screws that hold the top plate to the body

of the stove. The four screws pass upward through the slotted tabs at the top of each side and

into the underside of the top plate. Lift the top from the stove.

**NOTE: To protect the refractory package and the catalytic combustor from damage as you

work on the stove, remove these parts from the inner top. It may be necessary to rock the

catalyst gently to free it from the top.

5. Remove the Hearth.

Use a 5/32” Allen wrench to remove the two set screws which hold the hearth in place, and

remove the hearth.

6. Remove the Ash Door.

Pull the ash door hinge pins put, and remove the ash door.

7. Remove the Flue Collar.

While holding the nuts that are inside the flue collar with pliers, remove the two Phillips head

screws that hold the flue collar in place, and remove the flue collar.

8. Remove the Front.

Threaded studs are screwed into the back of the front plate. The studs pass through slotted

tabs in the side plates. Nuts screwed onto these studs hold the front to the sides of the stove.

Remove the two nuts and washers, being careful to hold the front in place as you remove the

last nut. Lift the front from the stove.

**NOTE: Stoves are constantly being improved. You may notice some small differences

between the stove you are working on and these instructions. These instructions will serve as

a guide for disassembling and assembling your stove.

9. Remove the Balance Air Plate.

Remove the two hex head cap screws that hold the balance air plate to the inside of the right

side plate, and remove the air plate.

10.Remove the Grate Back.

Remove the two cap screws and washers that hold the grate back to the inner back, and

remove the grate back.

Remove the balanced air plate and the grate back

**NOTE: The next step is to remove the back. Before removing the back, brace the two sides

to prevent them from falling over when the back is removed. A pipe clamp adjusted to hold the

two sides together works well.*

11.Remove the Back.

Remove the nuts and washers on the two studs that hold the back to the sides, and remove

the back.

Remove the nuts and washers and remove the back.

On some older heaters, two additional screws, passing through tabs at the lower corners of the

back and into the bottom, helped secure the back. A long extension for a 7/16” socket is needed to

reach these screws.

**NOTE: Before continuing with the disassembly, brace the left side so that when the right

side, inner top and inner back are removed, the left side will remain upright.

12.Lift the Right Side from the Bottom.

13.Lift the Grate Frame from the Inner Bottom.

Lift the grate frame from the inner bottom. Remove the rocker and fixed grates.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DutchWest Heizung Handbücher

DutchWest

DutchWest 2479 Bedienungsanleitung

DutchWest

DutchWest 2478 Bedienungsanleitung

DutchWest

DutchWest 2460CE Montageanleitung

DutchWest

DutchWest 2478 Montageanleitung

DutchWest

DutchWest 2477 Bedienungsanleitung

DutchWest

DutchWest 2460 Bedienungsanleitung

DutchWest

DutchWest 2460 Montageanleitung

DutchWest

DutchWest 2479CE Bedienungsanleitung

DutchWest

DutchWest 2477 Montageanleitung

DutchWest

DutchWest 2463 Montageanleitung

DutchWest

DutchWest 2479 Bedienungsanleitung

DutchWest

DutchWest 2463 Bedienungsanleitung

DutchWest

DutchWest 2460CE Bedienungsanleitung

DutchWest

DutchWest 2460 Bedienungsanleitung

DutchWest

DutchWest 2479 Bedienungsanleitung

DutchWest

DutchWest 2477 Bedienungsanleitung

DutchWest

DutchWest 2460 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung