Dyconn Duplex Series Bedienungsanleitung
2
Dual TV/Monitor Grommet Desk Mount (Duplex Series)
Model: DE9E2S-G
Instruction Manual
Images may different from actual product
Disclaimer
It is Dyconn’s intention to have all the correct information represented within this manual.
Although we try our best, Dyconn makes no claim that the information comprised herein
covers all conditions or details in connection with installation or use of this product. Dyconn
assumes no responsibility for accuracy or adequacy of information comprised in this
document. The information comprised here is subject to change without notice or obligation
of any kind
•A warning alerts you to the possibilities of personal injury or damage to equipment
if you do not follow the corresponding instructions. It is the installer's responsibility
to make sure all components are properly assembled and installed using the
instructions manual provided.
•Using improper screws or screw size may damage your display. If spacers are
required, be sure to use correct size of screws. Proper screws will easily and
completely thread into the display mounting holes. Inadequate thread
engagement in the display may cause display to fall.
•It is installer’s responsibility to make sure the combined weight of all components
does not exceed weight capacity. Exceeding weight capacities can result in
severe personal injury or damage to equipment.
•Allowing any part of your component cables to be caught between movable parts
can result in serious personal injury or damage to equipment.
Read the following warning before installing
!Verify all parts are included. Do not install if the products or hardware is damage. Not
all hardware included will be used.
!Please contact a qualified installer.
!This product contain moving parts, Use with caution.
!Determine approximate location for mounting and keeping in mind the display size,
extension, height adjustment and pitch / roll requirements.
!This product contains small item, keep these items away from children
!Do not exceed the maximum weight capacity for this product. Exceeding the weight
capacity can result in serious personal injury or damage to equipment!
3
Specifications
Dual Monitor - 23.6” (600mm) 1Crossbar 14” (355mm) -19” (482mm)
Dual Monitor – 35.4” (900mm) 1Crossbar 20” (508mm) – 30” (762mm)
Triple Monitor - 35.4” (900mm) 1Crossbar 14” (355mm) -19” (482mm)
Quad Monitor - 23.6” (600mm) 2Crossbars14” (355mm) -19” (482mm)
Quad Monitor – 35.4” (900mm) 2Crossbars20” (508mm) – 30” (762mm)
Six Fold Monitor - 23.6” (600mm) 2Crossbars14” (355mm) -19” (482mm)
Product Dimension
Each Monitor Weight Capacity
19.8(LBS) / 9(KG)
Suits Monitor Size
14”(355mm)-30”(762mm)
Distance from Pole (Closed)
5.3”(134mm)
Tilt adjustment
+/- 40 degree
Display Swing- Side to side
+/- 15 degree
Pivot
360 degree
Maximum Mounting Surface Thickness
3.7”(95mm)
VESA Compatibility
75x75mm and 100x100mm
Allowable Monitor Width vs. Horizontal Crossbar
Number of Monitors Monitor Width
Width refers to Monitor outer dimensions
Each Monitor supports a maximum weight of 19.8LBS (9KG)
4
Supplied Parts
5
Required Tools
ASSEMBLY and INSTALLATION
INSPECT THE MOUNT BEFORE ASSEMBLY
1. Carefully inspect/verify that all components are present.
2. If the mount/components are damaged or missing, please contact the company/seller
of the product you purchased and report the issue.
Note: Read all assembly instructions before staring the installation process.
6
Figure 1-1
Step 【1】Installation of Desk Clamp
Using improper screws or screw size may damage your display. If spacers are required,
be sure to use correct size of screws. Proper screws will easily and completely thread into
the display mounting holes. Inadequate thread engagement in the display may cause
display to fall.
Note: It is installer’s responsibility to make sure the desktop structure to which this
product is attached can support the combined weight of all components
Installation to Desk
1. Detach Base Cover and Base (3) as shown. (See Figure 1-1)
2. Place Base (3) on to mounting surface and secure using Pressure Clamp (2) as
shown (See Figure 1-2)
Figure 1-2
7
3. Attach the Upright Pole (5) to the Base (3). Turn and tighten by hand so the Upright
Pole assembly is firmly in place. Once the Upright Pole is in position, proceed to tighten
the Hex Screws M6x5mm using Allen Wrench 3mm (14) provided to secure the Upright
Pole.
4. Feed the cables through the Cover. Place the Cover over Upright Pole (5) and cables
should be completely inserted through the mounting surface as shown. (See Figure 1-4)
Ensure to leave enough slack in the cables to allow for movement of the monitors.
Figure 1-3
Figure 1-4
8
Figure 2-1
Figure 2-3
Figure 2-2
Step 【2】Horizontal Crossbar Assembly
Horizontal Crossbar Assembly
1. Place the Adjustable Lock Collar (4). You will need to loosen the Collar，position at
desired height. Tighten by hand so the Adjustable Lock Collar assembly is firmly in
place (See Figure 2-1)
2. Proceed to attach the Horizontal Crossbar (6) by insert it down from the top to the
assembly Upright Pole (5). (See Figure 2-2)
3. Once you have determined the mounting height and ensure that the Horizontal Crossbar
is aligned. You require it by hand threading the Knob (15) so the Horizontal Crossbar
assembly is firmly in place. (See Figure 2-3)
9
Figure2-4
Figure 2-5
4. Detach Horizontal Crossbar Cover from Horizontal Crossbar (6) as shown. (See
Figure 2-4)
5. Feed the cables into cable slot on the Horizontal Crossbar as shown. (See Figure 2-5)
10
Step 【3】Display Installation
Using improper screws size may damage your display. If spacers are required, be sure to
use correct size of screws. Proper screws used will easily and completely thread into the
display mounting holes. Inadequate thread engagement in the display may cause display
falling.
It is installer’s responsibility to make sure the combined weight of all components does not
exceed weight capacity. Exceeding weight capacities can result in severe personal injury
or damage to equipment.
Attaching the Display
1. Ensure Mount Bracket (1) assembly is able to swivel and tilt easily. (See Figure 3-1)
2. Carefully place the display face down on protective surface (See Figure 3-2)
Figure 3-2
Figure 3-1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Dyconn TV-Halterung Handbücher
