Dymo LabelWriter SE450 Label Printer Gebrauchs- und Pflegehandbuch

Technical Reference

DYMO LabelWriter SE450 Label Printer

No part of this document or the software may be reproduced or transmitted in any form or

by any means or translated into another language without the prior written consent of

Sanford, L.P.

Trademarks

LabelWriter and DYMO are trademarks or registered trademarks of Sanford, L.P. All other

trademarks are the property of their respective holders.

Description: Direct Thermal Printer

Model: LabelWriter SE450

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC (Federal Communications Committee) rules. These

limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency

energy, and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try correcting

the interference by one or more of the following measures:

nReorient the receiving antenna.

nIncrease the separation between the equipment and the receiver.

nConnect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

nUse shielded cables to connect this device to computers.

nConsult the dealer or an experienced radio/TV technician for help.

nChanges or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment and void the

manufacturer’s warranty.

Certification

This device has been tested and complies with the requirements of:

UL 1950

EN60950: Low Voltage Directive Product Safety

FCC Part 15 Class B

EN55022: Radiated and Conducted Emissions B

EN50082-1: Generic Immunity ESD, RF, and Transient Susceptibility

Contents

Introduction 1

Configuring the Host Computer for RS-232 Serial Interface 3

RS-232 Settings 3

RS-232 Cabling 4

RS-232 Signal Levels 4

Programming Overview 5

Programming the LabelWriter Printer 5

Resetting the Printer 6

Command Parameters 6

Character Evaluation 6

16-Bit Character Parameters 6

Conversions 7

Font Specifications 8

Objects 8

Print Modes 8

Raster Mode 9

Orientation 9

Portrait Mode 9

Landscape Mode 10

Text Objects 10

Barcode Objects 11

Graphic Objects 12

Line Objects 12

Command Reference 13

Alphabetical Command List 13

Commands by Function 15

Position Control 15

Font Control 16

Barcodes 17

Miscellaneous 17

Printable Characters 17

Raster Compatibility 18

Commands 18

20h - FFh Printable Characters 18

iii

CR Carriage Return 19

DC4 Cancel Double Wide Mode 19

ESC A Return Printer Status 20

ESC a Return Hardware Status 20

ESC B Set Dot Tab 20

ESC c Set Print Temperature to Low 21

ESC D Set Bytes per Line 21

ESC d Set Print Temperature to Medium 21

ESC E Form Feed 22

ESC e Set Print Temperature to Default 22

ESC F 1 n Feed n Lines 23

ESC g Set Print Temperature to High 23

ESC h Set Print Speed to Fast 23

ESC i Set Printing Speed to Barcode 23

ESC J Feed n Lines 23

ESC L Set Feed Length 24

ESC M Set Font to 12 cpi 24

ESC P Set Font to 16 cpi 25

ESC Q Set Top Margin 26

ESC S Set Font to 20 cpi 26

ESC T Set Font to 7 cpi 26

ESC U Set Font to 10 cpi 27

ESC V Return Firmware Revision 28

ESC W Wrap Data 28

ESC X Set Horizontal Starting Position 29

ESC Y Set Vertical Starting Position 29

ESC y Set 203 x 203 dpi 30

ESC z Set 136 x 203 dpi 30

ESC * Reset to Defaults 30

ESC @ Reset to Power-up Condition 30

ETB Raster Mode Compressed Graphics 31

FF Form Feed 32

GS A Starting Position of Bar Code 33

GS DC2 Set Font to Double Height 33

GS DC3 Cancel Double Height 34

GS d Feed n Text Lines 34

GS h Set Barcode Height 35

GS k Print Barcode 35

Data Matrix Barcode 36

PDF417 2D Barcode 39

GS l Draw Line in Landscape Mode 41

GS L Set Feed Length 43

GS q Print UPC/EAN Checksum 44

GS RS Set Inverse Print Mode 44

GS S Return Printer Status 45

GS T Select Line Wrap/Truncate Modes 46

GS t Set Characters per Line in Landscape 46

GS US Cancel Inverse Print Mode 47

GS u Set Characters per Line in Portrait 47

GS V Set Print Orientation 48

GS W Set Bar Code Element Width 48

GS w Set Barcode Module Width 49

GS ~ Enter Debug Mode 49

GS * Landscape Mode Graphics 50

HT Horizontal Tab 51

LF Line Feed 51

SO Set Font to Double Wide Mode 51

SYN Raster Mode Graphics 52

The Caret Feature 53

Activating the Caret Feature 53

Using the Caret Feature 53

Character Codes 55

Configuration Menu 65

Printer Specifications 67

Hardware Specifications 67

Interface Specifications 67

Print Head Specifications 67

USB Settings 69

Serial Interface Specifications 69

This page intentionally left blank for double-sided printing.

Introduction

The LabelWriter SE450 printer is a compact, thermal-transfer label printer. Featuring both

RS-232 serial and USB connections and including both an ASCII command set as well as

raster printing modes, this printer can fit a wide variety of uses.

The LabelWriter SE450 printer can be readily connected to most common computer systems

using the included Windows, Mac or Linux drivers. Or, for driver-less applications, the

printer can be connected and driven entirely by ASCII Escape commands. This makes the

LabelWriter SE450 an ideal printer to use in embedded applications, including medical

devices, paint matching systems, and so on.

The LabelWriter SE450 printer can accept label material up to 62 mm (2.44") wide, and has

a 57 mm (2.24") wide, 203 dot-per-inch (dpi) print head.

This Technical Reference provides all the information you need to be able to print labels

with the LabelWriter SE450 printer.

In addition, Windows and Mac sample code is available on the CD that came with the

LabelWriter SE450 printer.

In this Technical Reference, you will find:

nInformation about how to configure the host computer to communicate with the

LabelWriter SE450 over an RS-232 serial interface.

nInformation about programming the LabelWriter SE450 printer

nA list of commands by function

nA complete alphabetical command reference

nA complete list of the standard and extended ASCIIcharacter codes supported by the

printer

nInstructions for configuring the printer

nPrinter specifications

As an additional resource, visit the Developer's Forum on the DYMOWeb site.

Chapter 1

This page intentionally left blank for double-sided printing.

Configuring the Host

Computer for RS-232

Serial Interface

This chapter describes how to configure the host computer to communicate with the

LabelWriter SE450 printer over an RS-232 serial interface.

nRS-232 Settings

nRS-232 Cabling

nRS-232 Signal Levels

For information about communicating with the host computer using the USB port, see the

sample code located on the LabelWriter SE450 CD that came with the printer.

RS-232 Settings

In order for the host computer to communicate with the LabelWriter SE450 printer, the

communication parameters must be set as follows:

Baud Rate 9600

Data Bits 8

Stop Bits 1

Parity None

These settings can often be set using a BIOS setup program or an Operating System Control

Panel application. For embedded applications, you may need to build these settings into the

embedded system's initialization code.

Most languages provide a command or function to initialize a serial port.

If programming under Windows using Microsoft C/C++, use the function:

bios_serialcom()

Other C compilers offer a similar function. Consult your compiler user guide for the

appropriate function to use to configure a serial port.

If you are using the Unix OS, you’ll need to configure the RS-232 port as a dumb printer

port, with no special handling, control characters or form feeds. The LabelWriter printer will

handle these functions internally.

Chapter 2

Configuring the Host Computer for RS-232 Serial Interface

RS-232 Cabling

RS-232 cable pinouts are shown in the table below. For details on RS-232 signal names,

consult the RS-232 Standard documentation.

Origination

(Mod. 8 x 8)

Termination

(DB9S) Name Dir Description

1 8 RTS Out Printer is ready to receive data

2 3 RX In Data to the printer

3 2 TX Out Data from the printer

4 5 GND -- Signal, earth, and power ground

5 7 CTS In Depends on software selection

6 6 DTR Out Indicate printer is online

Modular Plug

RS-232 Signal Levels

The serial interface uses standard RS-232 signal levels as shown in the table below:

Signal Level Input Output

MARK (1) -27 V to -5 V -5 V

SPACE (0) +5 V to +27 V +12 V

RS-232 signal levels.

Andere Handbücher für LabelWriter SE450 Label Printer

Inhaltsverzeichnis

Andere Dymo Etikettendrucker Handbücher

Dymo

Dymo 4500 Bedienungsanleitung

Dymo

Dymo LabelPOINT 100 Bedienungsanleitung

Dymo

Dymo LabelWriter 400 Turbo Bedienungsanleitung

Dymo

Dymo DYMOLM200 Bedienungsanleitung

Dymo

Dymo LabelWriter 4XL Label Printer Bedienungsanleitung

Dymo

Dymo 1575 Bedienungsanleitung

Dymo

Dymo LetraTag LT-100T Bedienungsanleitung

Dymo

Dymo MobileLabeler Bedienungsanleitung

Dymo

Dymo LabelWriter 450 Duo Label Printer Bedienungsanleitung

Dymo

Dymo LabelManager Series Bedienungsanleitung

Dymo

Dymo Rhino 5200 Installationsanleitung

Dymo

Dymo Junior Bedienungsanleitung

Dymo

Dymo LabelWriter 450 Bedienungsanleitung

Dymo

Dymo LabelManager 350D Bedienungsanleitung

Dymo

Dymo Rhino Pro 5000 Bedienungsanleitung

Dymo

Dymo LabelPoint 250 Bedienungsanleitung

Dymo

Dymo LabelManager 100 Bedienungsanleitung

Dymo

Dymo LabelManager Wireless PnP Bedienungsanleitung

Dymo

Dymo LabelManager 210D Bedienungsanleitung

Dymo

Dymo DYMO Organizer Xpress Embossing Label Maker Bedienungsanleitung

Dymo

Dymo LetraTag XR Bedienungsanleitung

Dymo

Dymo LabelWriter 400 Bedienungsanleitung

Dymo

Dymo LabelWriter 400 Duo Guide Bedienungsanleitung

Dymo

Dymo 9000 Bedienungsanleitung

Beliebte Etikettendrucker Handbücher anderer Marken

Brother

Brother P-Touch 2420PC Bedienungsanleitung

newell

newell Dymo LabelManager 210D Bedienungsanleitung

Brother

Brother TD-4000 Bedienungsanleitung

U-Line

U-Line BROTHER H-8754 Bedienungsanleitung

Tharo Systems

Tharo Systems H-435+ Bedienungsanleitung

Brother

Brother E300 Bedienungsanleitung

Godex

Godex RT700 SERIES Bedienungsanleitung

ID Technology

ID Technology 252 Bedienungsanleitung

Labelmate

Labelmate MC-11 Bedienungsanleitung

CAB

CAB XD4M/300 Bedienungsanleitung

Avery Dennison

Avery Dennison Pathfinder 6057 Service-Handbuch

Brother

Brother P-touch PT-9700PC Bedienungsanleitung

TSC

TSC PEX1000 Series Bedienungsanleitung

Adkins

Adkins Label Master Bedienungsanleitung

Epson

Epson LabelWorks LW-400 Bedienungsanleitung

Primera

Primera 510212 Bedienungsanleitung

Brady

Brady BradyPrinter S3100 Bedienungsanleitung

DuraLabel

DuraLabel LabPRO Bedienungsanleitung