Dynamic Engineering PMC-UNIV-TEST Bedienungsanleitung

DYNAMIC ENGINEERING

150 Dubois St. Suite C, Santa Cruz, CA 95060

831-457-8891 Fax 831-457-4793

http://www.dyneng.com

[email protected]

Est. 1988

User Manual

PMC-UNIV-TEST

PMC-UNIV-TEST-ENG

Revision A1 Revised 9/24/18

Corresponding Hardware: Revision A

Fab numbers: 10-2018-1201

Embedded Solutions Page 2

PMC-UNIV-TEST

PCI and PMC Compatible Carrier

Dynamic Engineering

150 Dubois St. Suite C

Santa Cruz, CA 95060

831457-8891

831457-4793 FAX

This document contains information of

proprietary interest to Dynamic Engineering. It

has been supplied in confidence and the

recipient, by accepting this material, agrees that

the subject matter will not be copied or

reproduced, in whole or in part, nor its contents

revealed in any manner or to any person except

to meet the purpose for which it was delivered.

Dynamic Engineering has made every effort to

ensure that this manual is accurate and

complete. Still, the company reserves the right

to make improvements or changes in the

product described in this document at any time

and without notice. Furthermore, Dynamic

Engineering assumes no liability arising out of

the application or use of the device described

herein.

The electronic equipment described herein

generates, uses, and can radiate radio

frequency energy. Operation of this equipment

in a residential area is likely to cause radio

interference, in which case the user, at his own

expense, will be required to take whatever

measures may be required to correct the

interference.

Dynamic Engineering’s products are not

authorized for use as critical components in life

support devices or systems without the express

written approval of the president of Dynamic

Engineering.

Connection of incompatible hardware is likely to

cause serious damage.

Other trademarks and registered trademarks are owned by their

respective manufactures.

Embedded Solutions Page 3

PRODUCT DESCRIPTION 4!

Headers and TestPoints 6!

PMC Module Backplane IO Interface Pin Assignment 7!

Construction and Reliability 8!

Thermal Considerations 8!

WARRANTY AND REPAIR 9!

Service Policy 9!

Out of Warranty Repairs 9!

For Service Contact: 9!

SPECIFICATIONS 10!

ORDER INFORMATION 11!

FIGURE 1!PMC-UNIV-TEST PN4 INTERFACE STANDARD 7!

Table of Contents

List of Figures

Embedded Solutions Page 4

Product Description

PMC-UNIV-TEST and PMC-UNIV-TEST-ENG are part of the Dynamic Engineering PCI

and PMC Compatible family of modular I/O components. Both adapt a PMC to one PCI

slot. The devices are for test support. Testpoints for the PCI bus plus JTAG are

provided on both versions.

In a PCI position, the B side is forward the A side is the rear. PMC-UNIV-TEST has the

Host/carrier side connectors mounted to the A side. The PMC will have it’s main

component side forward in this configuration. The SCSI connector is routed to the Jn4

/ Pn4 PMC connector to provide a method of connecting to “user IO” while testing.

“B” Front side with the testpoints and SCSI.

“A” Rear side with carrier type connectors to mate to PMC.

Note mounting holes to optionally connect PMC to Carrier via 10 mm standoff positions.

Embedded Solutions Page 5

PMC-UNIV-TEST-ENG has some modifications when compared with the standard

version. The B side PMC type connectors are added, the SCSI is removed, and the

testpoints are moved to the opposite side. In this configuation the PMC side connectors

can be installed into the host board, and the PMC can be installed into the carrier

connectors on the A side [now facing up]. The testpoints are now on the A side to make

them more convenient and provide a method of probing the PCI bus while the PMC is

installed into the carrier via PMC-UNIV-TEST-ENG.

“B” Front side with the PMC type connectors – “plugs into

host”

“A” Rear side with carrier type connectors to mate to PMC.

Note headers are this side for the –ENG configuration as it will be up to mate with the

PMC. The headers will be away from the PMC A secondary riser may be required with

cPCI etc depending on how low the PMC connectors are located to the bottom edge of

the carrier.

Special features:

• Passive 32 bit Universal voltage design

• Bipass capacitors on all PMC power pins plus 10 uF on 5V and 3.3V.

• JTAG header routed to PMC connections

• PCI test points – easy to read staggered Silk labels both sides

• 8 grounds to support logic analyzer connection as well as ocilloscope

• User IO [Pn4] available through SCSI connector on standard model.

Embedded Solutions Page 6

Headers and TestPoints

PCI 56 testpoints are supplied each labeled with the PCI signal attached. Some names

are truncated to allow larger easier to read print.

JTAG TRST, TDI, TDO, TMST, TCK plus a 3.3V and a Ground reference to interface

with the installed PMC via the JTAG signals.

GND 8 Ground testpoints are spaced along the top of the PCI signals to support Logic

Analyzer and Ocilloscope reference. Each are labeled GND.

Embedded Solutions Page 7

PMC Module Backplane IO Interface Pin Assignment

The figure below gives the pin assignments for the PMC Module IO Interface – from

Pn4 to the PCIeBPMCX1 connectors. Also see the User Manual for your PMC board for

more information.

SCSI II [P2] Pn4

35 36 1 2

1 2 3 4

37 38 5 6

3 4 7 8

39 40 9 10

5 6 11 12

41 42 13 14

7 8 15 16

43 44 17 18

9 10 19 20

45 46 21 22

11 12 23 24

47 48 25 26

13 14 27 28

49 50 29 30

15 16 31 32

51 52 33 34

17 18 35 36

53 54 37 38

19 20 39 40

55 56 41 42

21 22 43 44

57 58 45 46

23 24 47 48

59 60 49 50

25 26 51 52

61 62 53 54

27 28 55 56

63 64 57 58

29 30 59 60

65 66 61 62

31 32 63 64

33 67 Open

34 68 Open

FIGURE 1 PMC-UNIV-TEST PN4 INTERFACE STANDARD

Read table:

P2-1 = Pn4-3

P2-35 = Pn4-1

etc.

Signals are matched length and differentially routed with 100 ohm impendance

Embedded Solutions Page 8

Construction and Reliability

PMC-UNIV-TEST is constructed out of 0.062 inch thick high temp RoHS compliant FR4

material.

Surface mounted components are used. The connectors are SMT for the PMC bus and

through hole for the testpoints and IO.

The PMC Module connectors are keyed and shrouded with Gold plated pins on both

plugs and receptacles. They are rated at 1 Amp per pin, 200 insertion cycles minimum.

These connectors make consistent, correct insertion easy and reliable. With careful

installation the connectors will last longer and jambing on will result in a shorter lifespan.

The PMC Module is secured against the carrier with the PMC connectors. It is

recommended, for enhanced security, that the PMC mounting screws are installed. The

screws and stand-off’s are supplied with the PMC from the OEM. Dynamic Engineering

has screws, standoffs, blank bezels and other PMC hardware available at a reasonable

cost if your PMC was not shipped with some of the required attachment hardware or if it

has been misplaced.

Thermal Considerations

If the PMC installed has a large heat dissipation; forced air cooling is recommended.

Since the PMC is vertical and the lid is off the box, standard air-flow may need to be

enhanced.

Embedded Solutions Page 9

Warranty and Repair

Please refer to the warranty page on our website for the current warranty offered and

options.

http://www.dyneng.com/warranty.html

Service Policy

Before returning a product for repair, verify as well as possible that the suspected unit is

at fault. Then call the Customer Service Department for a RETURN MATERIAL

AUTHORIZATION (RMA) number. Carefully package the unit, in the original shipping

carton if this is available, and ship prepaid and insured with the RMA number clearly

written on the outside of the package. Include a return address and the telephone

number of a technical contact. For out-of-warranty repairs, a purchase order for repair

charges must accompany the return. Dynamic Engineering will not be responsible for

damages due to improper packaging of returned items. For service on Dynamic

Engineering Products not purchased directly from Dynamic Engineering contact your

reseller. Products returned to Dynamic Engineering for repair by other than the original

customer will be treated as out-of-warranty.

Out of Warranty Repairs

Out of warranty repairs will be billed on a material and labor basis. Customer approval

will be obtained before repairing any item if the repair charges will exceed one half of

the quantity one list price for that unit. Return transportation and insurance will be billed

as part of the repair and is in addition to the minimum charge.

For Service Contact:

Customer Service Department

Dynamic Engineering

150 DuBois St. Suite C

Santa Cruz, CA 95060

831-457-8891 831-457-4793 fax Internet Address [email protected]

Embedded Solutions Page 10

Specifications

Logic Interfaces: PCI 32 bit Universal Voltage.

Access types: All PCI supported

CLK rates supported: 25-66 [likely work at higher rates as PCI signals are matched and

controlled. ]

Software Interface: Passive, no SW required for adapter

Testpoints: PCI signals plus JTAG and grounds

Interface: PMC front bezel directly, rear IO via SCSI connector.

Dimensions: minimized to cover as little of the PMC as possible.

Construction: High Temp FR4 Multi-Layer Printed Circuit, Through Hole and

Surface Mount Components.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dynamic Engineering Steuereinheit Handbücher

Dynamic Engineering

Dynamic Engineering PMC-BiSerial-III SDLC Bedienungsanleitung

Dynamic Engineering

Dynamic Engineering PMC-BISERIAL-III RL1 Bedienungsanleitung

Dynamic Engineering

Dynamic Engineering IP-429-II Bedienungsanleitung

Dynamic Engineering

Dynamic Engineering IP-CF Bedienungsanleitung

Dynamic Engineering

Dynamic Engineering PMC-BiSerial-III HW2 Bedienungsanleitung

Dynamic Engineering

Dynamic Engineering PCIeBiSerialDb37-BA22 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung