E-TINT CTRL MG1 Bedienungsanleitung

cTRL®Mg1 • Owner’s manual

This e-Tint® powered goggle meets MIL-PRF-32432A. Please follow these care and usage instructions to ensure optimal performance from your eyewear.

GLOSSARY OF TERMS ACTIVATE: Turn on; tint | DEACTIVATE: Turn off; clear

The CTRL®MG1 electronic-tinting goggle changes instantly between two levels of tint (on or off) by either a quick press of the button or automatically

via the built-in light sensor. These tint levels are fixed and cannot be changed by the user. The goggle comes pre-programmed with a standard setting

for automatic mode. You can adjust the light sensitivity if you determine that it does not automatically turn on or off to your liking (see “Adjust Light

Sensitivity” below).

TO OPERATE IN MANUAL MODE:

Quickly press and release the button to activate or deactivate the tint of the goggle.

TO OPERATE IN HANDS-FREE (AUTOMATIC) MODE:

The CTRL®MG1 goggle can automatically tint in the presence of an activating light. To switch the system to automatic mode, simply press and hold

the button for approximately three (3) seconds. The lens will flash to indicate it has been switched into automatic mode. Release the button. The goggle

is now set for hands free (automatic) use.

TO EXIT HANDS-FREE (AUTO) MODE, AND ENTER MANUAL MODE:

Press the button once to go back to manual mode. Note: The lens will turn clear upon exiting automatic mode.

TO ADJUST LIGHT SENSITIVITY:

First, switch the goggle to automatic mode. Choose an ambient area of light that would be similar to where you would prefer the goggle to activate. Stand

in your desired lighting condition. Press & hold the button for about four (4) seconds. After four seconds, the lens will flash to indicate the system has

re-calibrated its sensor to your desired setting. Light that is as bright as, or brighter than, your selected ambient lighting will now trigger the sensor. The

electronics will store this custom setting until it is re-adjusted or reset to its factory setting. NOTE: Be sure to keep the area around the light sensor

clear and open to the light source. If your finger is covering the light sensor during the adjustment, the goggle will stay activated most of the time and

only switch when it is very dark. Do NOT attempt to change the light sensitivity when moving.

FOR A FACTORY RESET:

A factory reset can be performed in either manual or automatic mode. Press and hold the button for approximately six (6) seconds. The lens will cycle

through (2) sets of flashing. After the second set of flashing, the goggle will be restored to its original factory settings.

CHARGING: Connect the supplied USB cable to goggle and charge with the e-Tint®charging pack, wall adapter, or computer. The lens will tint when

charging and turn off when fully charged. A completely depleted battery will take up to two (2) hours to fully charge. Directions for use of the charging

pack are included with the charger.

CHARGING STORAGE: If the goggle will be stored for a prolonged period of time, we recommend to fully charge the battery every 2-3 months or

charge in ‘storage mode’ with the e-Tint® charging pack. Doing so will prolong and protect the capacity of the goggle battery. Directions for use of the

charging pack are included with the charger.

WARNING! IF GOGGLE, USB CABLE, OR CHARGER HAVE BEEN EXPOSED TO EXCESSIVE SWEAT OR MOISTURE, ALLOW UNIT TO DRY (APPROX. 8

HRS.) BEFORE CHARGING. DO NOT STORE GOGGLE CONNECTED TO A CHARGING SOURCE FOR AN EXTENDED PERIOD OF TIME (UNLESS IT IS

CONNECTED TO THE E-TINT®CHARGER IN STORAGE MODE).

Directions of use

FOLLOW THESE INSTRUCTIONS TO INSTALL YOUR PRESCRIPTION (Rx)* CARRIER AND Rx CONNECTOR INTO THE CTRL®MG1 GOGGLE.

*Prescription (Rx) must be prepared by a licensed optician.

1. Switch the goggle into the “off” or clear state.

2. Insert the Rx Carrier into the Rx Connector by aligning the rectangular post at the center of the Rx Carrier with the rectangular hole on the Rx Connector.

Gently push Rx Carrier down until it snaps securely into place

(Diagram 1).

3. Insert the Rx Carrier into the goggle frame by first fitting the keyhole notches over the posts at the nose bridge

(Diagram 2).

Be sure the soft bumper

pad faces toward the lens, away from the face.

Prescription (Rx) carrier

USB PORT

ACTIVATION BUTTON

• Press button to tint ON and OFF

• Press & hold button 3 seconds for hands-free (auto) mode

• Adjust the light sensitivity (see instructions below)

LIGHT SENSOR

INTERCHANGEABLE LENS

ADJUSTABLE HEAD STRAP

WARNING! DO NOT USE tinted lenses in the dark. DO NOT USE if lenses are scratched. IT IS YOUR RESPONSIBILITY TO DETERMINE THE SUIT-

ABILITY OF THIS PRODUCT FOR ITS INTENDED USE. IF AT ANY TIME YOUR GOGGLE IS NOT PERFORMING PROPERLY, DISCONTINUE USE OF THE

EYEWEAR AT ONCE. NOT RECOMMENDED FOR USE OR STORAGE IN TEMPERATURES BELOW -10°C (14°f) OR ABOVE 45°C (113°F).

e-TINT, LLC | WWW.E-TINTPRODUCTS.COM | (877) 451-5937 MADE IN THE U.S.A.

This product is subject to one or more U.S. or foreign patents listed at: e-tintproducts.com/intellectual property

CLEANING & CARE: Clean with warm water, mild detergent, and a soft cloth. For stubborn residues clean with a household glass cleaner. Do

not use cleaners which contain moisturizers, abrasives, strong acids, or caustics. Do not immerse the spectacle in liquids. Do not leave or

store goggle in excessive heat when not in use.

COMFORT & FIT: Tighten or loosen the goggle head strap by moving the strap-adjusting slide right or left.

All e-Tint®products are warranted to the original purchaser for six (6) months from the date of purchase against manufacturing

defects in materials and workmanship. Upon receiving returned product(s) that e-Tint determines to be defective, we will repair

or replace the product at our option. Please contact Customer Support at [email protected] for warranty service.

This warranty does not affect the legal rights of customers under applicable state or national laws governing the sales of

consumer goods.

EXCLUSIONS

The Return Policy and Limited Warranty does not apply to: (a) normal wear and tear, including scratched lenses; (b) water

damage; (c) damage due to neglect, abuse, misuse, or mishandling; (d) damage caused by improper storage or improper

maintenance; (e) damage caused by use of chemicals or improper cleaning; (f) damage due to accidents or acts of nature; and

(g) battery damage from improper use; (h) damage resulting from alterations, changes, or repairs not authorized in writing by

e-Tint.

Online Auction Purchases: Products purchased through online auctions (other than our primary websites or Authorized

Dealers) are not eligible for warranty coverage. Online auction confirmations are not accepted for warranty verification.

EXCEPT AS SET FORTH IN THE LIMITED WARRANTY, ALL E-TINT®PRODUCTS ARE PROVIDED ON AN “AS IS” BASIS. TO THE

EXTENT PERMITTED BY APPLICABLE LAW, ALL OTHER WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, ARE

EXPRESSLY DISCLAIMED.

LIMITED WARRANTY

RETURN POLICY

For warranty/repair service, or to return any new, unopened product for a full refund or exchange (within 30 days of purchase),

please contact Customer Support at [email protected] or visit www.e-tintproducts.com for a Return Merchandise Autho-

rization (RMA) number and specific shipping instructions. Products returned for a full refund must be in new condition and in original

packaging (including all accessories), and returned to us within 30 calendar days of the issuance of the RMA. A 20% restocking fee

may be charged for any accessories or components missing from the returned product. A purchase receipt MUST be provided with

the return of any product. Products returned without an RMA will not be eligible for a refund or exchange. The shipping and duty

charges for returning a product are the customer’s responsibility.

The following information is required for all returns:

• LOT NO. Found on the UPC label (on the retail box)

• SKU NO. Found on the UPC label (on the retail box)

• ORIGINAL PURCHASE RECEIPT

• FIRST & LAST NAME

• TELEPHONE NUMBER

• EMAIL & SHIPPING ADDRESS

visit www.e-tintproducts.com for instructional videos

1. Switch the goggle into the “off” or clear state.

2. Pull up the Velcro flap covering the plug on the back of the electronics module

(Diagram 3).

3. Carefully lift the flexible connection ribbon (“flex”) to disconnect the plug

(Diagram 4).

4. Push the flex through the slot in the frame

(Diagram 5).

5. With both hands, gently pull the nose bridge and brow section of the frame outward, releasing the lens from the frame’s pins

(Diagram 6).

6. Choose a new lens (either an e-Tint®lens or clear lens). If installing an e-Tint® lens, first thread the flex gently through the slot in the frame.