East Coast Gate Operators ECGO-GKP Benutzerhandbuch

Read Prior to Installing

***For Professional Install Only

ECGO-GKP Cellular Telephone Entry

4G with 3G Fallback Technology

Setup Manual

2 | Page

Contents

Contents ............................................................................................................................................................................2

Important Safety Instructions ..........................................................................................................................................3

Introduction ......................................................................................................................................................................4

ECGO-GKP Specifications..............................................................................................................................................4

Installation Instructions....................................................................................................................................................5

4G or 3G SIM card Standard Size Only ..........................................................................................................................5

Grounding Unit ..........................................................................................................................................................6

Power Supply.............................................................................................................................................................6

LED Indicators............................................................................................................................................................6

Programming via the ECGO App

(Recommended)

..........................................................................................................7

Home Page ....................................................................................................................................................................7

Add Owners ...................................................................................................................................................................8

Manage Friends and Family ..........................................................................................................................................8

Set 5 digit PIN Code.......................................................................................................................................................8

Other Options ................................................................................................................................................................9

Settings..........................................................................................................................................................................9

Programming ..................................................................................................................................................................10

Programming via Text.................................................................................................................................................10

Keypad Programming .................................................................................................................................................14

Operating the ECGO-GKP................................................................................................................................................15

ECGO Warranty................................................................................................................................................................16

3 | Page

Important Safety Instructions

When installing and using the unit, the following basic safety precautions should always be followed to reduce the

risk of fire, electric shock and personal injury.

•Unplug all the connections to the product before cleaning. Use a damp cloth for cleaning. Do not use

liquid cleaners or aerosol cleaners.

•Do not use this product around sprinkler outlets.

•Do not use this product near an area where there is a potential of a gas leak or fume that can be explosive.

•Do not place the unit near or over a radiator or any other heat source.

•Do not overload the wall outlet or power cord where the power adapter is installed. This can result in fire or

electric shock.

•Avoid spilling liquid on this equipment and do not insert any objects through the ventilation slots.

•Avoid using the equipment during an electrical storm. While unlikely, there is a remote risk of electrical

shock from lighting.

•Follow the instructions on the product.

4 | Page

Introduction

The ECGO-GKP 4G is a telephone entry system installed at the entrance of a building or outside of a gated area. It is

an ideal product to consider as a replacement for a traditional phone entry for the following reasons:

•very easy to install and works well with all gate operators

•allows the owner to save up to 1,150 phone numbers and/or 400 pin codes for family and visitors

•provides the ability to contact up to 3 owners on a cell or landline and will “roll-over” from the first, to second

to third when the “CALL” button is pressed

•sends report phone numbers and pin codes that enter the gate via text message to a specified number

•no trench required for phone line!

The ECGO-GKP gives you the opportunity not only to know who is waiting at the entrance from a remote location

but to also control the access point. Use of ECGO-GKP at your company or house does not require any special

installation and wiring. Simply install the unit and connect the output to gate operator and power supply.

ECGO-GKP Specifications

Operating Voltage

12 to 24 Volt DC/AC ONLY””

Operating Current

Maximum 250mA, Typically 55mA

Frequency

850/900/1800/1900 or 900/1800 MHz

Humidity

Less than 80% RH

Operating Temperature -20℃to 50℃

5 | Page

Installation Instructions

ECGO-GKP Control Board

4G or 3G SIM card Standard Size Only

Please refer to the flyer included with your ECGO-GKP unit with detailed instructions for the consumer when

selecting and purchasing your SIM card. The following should be noted:

•Request a standard size 4G SIM card (illustration above represents actual size of card). However, 3G is

compatible as well.

•If you have an AT&T or T-Mobile account, simply request that a new card/line is added to your account

•If you do not have an AT&T or T-Mobile account, purchase a pre-paid 4G SIM Card. Our recommendation is

to add $99** to your pre-paid card.

**The ECGO Cellular Telephone Entry system uses minutes only when an unknown number calls the sys-

tem and the call is routed to the owners’ phone that is specified upon set-up. For this reason, $99 is ade-

quate in most instances for more than a year.

•NO DATA IS REQUIRED ON YOUR CARD OR PLAN. Only Voice and Text Messaging is required.

•Be certain to:

1. Obtain the phone number associated to the SIM Card

2. ACTIVATE THE CARD BEFORE YOU LEAVE THE STORE

6 | Page

Once a SIM card has be acquired, insert the card into the SIM card holder shown in the illustration above and close

it carefully. After the SIM card is inserted and the power is connected, power the unit up. The unit will beep until it

connects to the cell tower.

Grounding Unit

Five wires are recommended for the ECGO:

•2 wires for power

•2 wires for command wires to gate operator

•1 wire for grounding run back to Main incoming power ground on gate operator

Power Supply

The ECGO-GKP is designed to work with power supplies 12V~24V AC/DC. The power supply should be capable of

supplying a constant current of no less than 1 amp. A transformer is supplied for your assistance. Connect a

12~24volt DC power supply to terminals marked “12V~24V AC/DC”. See the illustration above.

Antenna

Be very careful to not damage antenna wire and use the supplied gasket for the unit to remain watertight. Note

that seal damage to antenna will cause failure and void warranty

Hard Reset (to reset to factory settings)

After placing a jumper between the Ground and PBD (see illustration above), press and hold the red RESET button

until you hear “do” tone, then release all at once. Remove the jumper and power back up.

LED Indicators

LED “Intercom Status“ Indicator

LED “ Power “ Indicator

Keypad LED Status LED Status

Yellow (standby) Flashes once per 5 seconds Red (power on) Solid

Yellow (using)

Solid

Red (power off)

Off

LED “ Network “Indicator

LED

Status

Green (ready)

Flashes once per 3 seconds

Green (searching) Flashes once per second

Green (busy) Solid

7 | Page

Programming via the ECGO App

(Recommended)

If you have an android or Apple device, the owner can download

the ECGO app to easily configure their entry system by going to

the App Store, and searching for ECGO.

Note that most options will generate a text message that, when

prompted, you will need to send to the unit.

The following options are available from the main menu:

Home Page

Relay 1 – This is the relay to which the primary gate should be configured. The

homeowner has the following options from this page:

Open Gate

Hold Gate

Release Gate

Relay 2 – The ECGO-GKP can be wired to communicate to two devices. Typically,

when used, Relay 2 is configured to control a secondary gate, lights or garage

door. Consult with your installer or dealer to determine if and how Relay 2 is

needed.

8 | Page

Add Owners

The primary owner number must be added prior to adding “family and friends”.

Up to three owners may be added. The order (owner 1,2,3) that the owners are

specified is the same order that the unit will attempt to reach when the CALL

button on the unit is pressed.

Manage Friends and Family

Add up to 1,150 phone numbers of the guests that you would like to be

recognized when the unit is called. The primary gate should always be

configured to use Relay 1.

Relay 2 is characteristically used for a walk gate, garage door or possibly lights.

This is also where you would go to delete the number/s should you want to

remove access.

Set 5 digit PIN Code

Enter/delete up to 400 5-Digit PIN codes that will be recognized when accessing

the gate.

9 | Page

Other Options

Select here for the following:

Signal Strength,

Retrieve a list of numbers that have accessed the gate, and

Get Status

Settings

Navigate here to enter the phone number of the SIM Card inserted into the unit.

The homeowner also has the options to reset the programming code and/or

access code on this page. Please be aware that when the programming or access

code is reset, all programming messages sent to the units’ SIM card and

referenced later in this manual will need to reflect the new passcode.

10 | Page

Programming

Programming via Text

(Alternative when the App is not an option)

To add the gate owner/s (Up to three phone numbers are allowed 3 owners)

You can text the message from your cell phone, computer, etc. Additional options that work well are Google Voice

or www.onlinetextmessage.com.

The messages should be sent to the number associated to the SIM card that was purchased for the unit. Type the

code (see examples below) into the message box and send. Once this has been done, the device from which the

message was sent will receive a response from the unit stating that the message was received. Note that a

response may take up to 40 seconds. "OK" indicates success. If “OK” was not received, you may need to resend

the text again.

Note that the owner number must be added to the unit before “family and friends” can be entered.

The following example illustrates the message that should be used to program the owner/s:

You may program up to three owners as follows:

Add Owner 1: *12*1234#11 owners’ area code & phone number

Add Owner 2: *12*1234#12 owners’ area code & phone number

Add Owner 3: *12*1234#13 owners’ area code & phone number

EXAMPLE:

If owner 1 # is 8038316013, your message should appear as follows:

*12*1234#118038316013#

Select SEND and within 40 seconds, you should receive an “OK” message in response.

Then proceed with owner 2 and 3, if applicable.

To add friends and family members that you wish to access the gate

Keep in mind that the ECGO-GKP has two Relays. As mentioned previously, the primary gate should always be

configured to use Relay 1. Therefore, when the owner is ready to grant access to the primary gate, Relay 1 should

be specified when configuring the system via text messaging.

Andere Handbücher für ECGO-GKP

Inhaltsverzeichnis

Andere East Coast Gate Operators Gegensprechanlage Handbücher

East Coast Gate Operators

East Coast Gate Operators ECGO-GKP Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung