Eaton ELC-PC12NNDR Bedienungsanleitung

IL0503017E.pdf

5011640402-SN02

2007-05-08

ELC-EX08NNSN

Switch-Type Digital Extension Module Instruction Sheet

1 WARNING

•Please read this instruction carefully before use.

•ELC-EX08NNSN is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity,

electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific

tools are required to open the enclosure) in case danger and damage on the device may occur.

•DO NOT tough any terminal when the power is switched on

•Warning – Do not disconnect while circuit is live unless area is known to be non-hazardous.

•Power, input and output (I/O) wiring must be in accordance with Class 1, Div. 2 wiring methods - Article 501-10(B)(1) of the

National Electrical Code.

•Suitable for use in Class 1, Division 2, Groups A, B, C, D or Non-Hazardous locations only.

•Warning – Explosion hazard - Substitution of components may impair suitability for Class 1, Division 2.

•Warning – Explosion hazard - Do not disconnect equipment unless power has been switched off or the area is known to be

Non-Hazardous.

2 INTRODUCTION

1. Thank you for choosing ELC series programmable logic controller. ELC-EX08NNSN shall be used together with ELC SLIM TYPE

occupying 8 input points. Including MPU, the digital I/O can be extended to maximum 256 points. Besides, maximum 8 special

extension modules (AN02NANN/AN04ANNN/AN04NANN/AN06AANN/PT04ANNN/TC04ANNN/MC01) are extendable from MPU.

2. No external power supply and signals are required, ELC-EX08NNSN allows you to directly control its input points by its switches.

3. As digital switches, ELC-EX08NNSN is able to input instructions without required external wiring for receiving signals. Besides,

ELC-EX08NNSN is handy and safe for using in teachings.

Product Profile

ELC-EX08NNSN

903

25.2

5.5

1X2

0ON

3.4

Unit: mm

1. DIN rail (35mm) 2. Extension unit/module connection port 3. Model name

4. Input indicators 5. DIN rail clip 6. Input switch

7. Fixing clip for extension unit 8. Nameplate 9. Extension unit/module connection port

10. Aiming pinhole for connection to MPU

IL0503017E.pdf

3 SPECIFICATION

3.1. Electrical Specification

Model

Items ELC-EX08NNSN

Power voltage 24VDC (-15%~20%) (Power is supplied by the internal bus of MPU)

Power consumption 0.5W

Anti-interference ability

ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT(IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV,

Analog & Communication I/O: 1KV

RS(IEC 61131-2, IEC 61000-4-3): 26MHz~1GHz, 10V/m

Operation/Storage Operation : 0°C ~ 55°C (Temperature), 50 ~ 95% (Humidity), Pollution degree 2

Storage: -25°C ~ 70°C (Temperature), 5 ~ 95% (Humidity)

Agency Approvals UL508

UL1604, Class1,Div2 Operating temperature code: T5

European community EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC

Vibration/ Shock immunity International standard: IEC61131-2, IEC 68-2-6（TEST Fc/IEC61131-2 & IEC 68-2-27 (TEST Ea)

Weight (g) 60g

4 INSTALLATION

1. Use a screwdriver to

open the side cover

and reveal the

connecting port.

2. Use the screwdriver

to lift and unfasten

the fixing clip.

3. Accurately connect

the extension module

to the MPU by using

the pinholes at each

corner.

4. Secure the

extension module to

the MPU by pushing

down the fixing

clips.

5. Order of the I/O point No.: The input points of the first extension module are lined up from X20 and output points are lined up from

Y20. The rule applies to all MPU connections with extension modules of any number of points.

Model Input points Output points No. of input points No. of output points

ELC-PC12NNDR 8 4 X0 ~ X7 Y0 ~ Y3

ELC-EX08NNSN 8 0 X20 ~ X27 -

ELC-EX16NNDR 8 8 X30 ~ X37 Y20 ~ Y37

5 TROUBLESHOOTING

Input LED Indicator

The On/Off of input signals can be indicated by the input LED indicator. When the input is On, the LED will be on. If error occurs, please

check if the loops of the LED and input signal are normal by using HHP/ELCSoft. Please also be aware that:

1. Do NOT place ELC-EX08NNSN under direct sunlight and please avoid placing it next to overheating objects in case the

high temperature will affect the functions of ELC-EX08NNSN.

2. Please clean the airborne or conductive dust on the panel on a regular basis.

Andere Handbücher für ELC-PC12NNDR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton Steuereinheit Handbücher

Eaton

Eaton ELC-COPBDP Bedienungsanleitung

Eaton

Eaton EC4E-221-6D4T1 Handbuch

Eaton

Eaton XIOC-SER Handbuch

Eaton

Eaton Cutler-Hammer PanelMate ePro PS Series Bedienungsanleitung

Eaton

Eaton Moeller SL7-CB Series Handbuch

Eaton

Eaton PSG480B24RM Bedienungsanleitung

Eaton

Eaton Digitrip RMS 910 Handbuch

Eaton

Eaton i-on30R Bedienungsanleitung

Eaton

Eaton PXR-PCAM Handbuch

Eaton

Eaton COOPER POWER SERIES Bedienungsanleitung

Eaton

Eaton Form 4D Recloser Control Bedienungsanleitung

Eaton

Eaton PowerXL DX-NET-DEVICENET Bedienungsanleitung

Eaton

Eaton Eaton 5PX Montageanleitung

Eaton

Eaton CEAG DLS/3PH-BUS-Module-inverse Service-Handbuch

Eaton

Eaton Power XL SmartWire-DT DX-NET-SWD1 Handbuch

Eaton

Eaton Vickers CM2 Series Bedienungsanleitung

Eaton

Eaton xComfort F94 Series Bedienungsanleitung

Eaton

Eaton CBEU-02/03 Bedienungsanleitung

Eaton

Eaton Vickers DG3V-8 Series Bedienungsanleitung

Eaton

Eaton Crouse-hinds series Bedienungsanleitung

Eaton

Eaton Vickers FCGT-02-A-11 Series Bedienungsanleitung

Eaton

Eaton DeviceNet Bedienungsanleitung

Eaton

Eaton Char-Lynn 5 Series Bedienungsanleitung

Eaton

Eaton HMi VU Series Handbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung