Eaton SCD24 Bedienungsanleitung

SCD24

24 Channel DMX Source Controller

Installation guide

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 2

Contents

Introduction 3

Dimensions 3

Technical Data 3

Mounting 4

DMX Connections 4

Connecting to the Mains 4

Network Connections 5

Network Termination 5

Service Switches and LEDs 6

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 3

Introduction

The iLight 24 channel DMX source

controller is designed to provide control

of any DMX512 controllable device. This

product is of particular use for controlling

DMX LED colour changing units and

entertainment devices.

Each channel can be assigned a

DMX channel from within the iLight

programming software. The SCD24

can be controlled like any other iLight

Source Controller using any of the iLight

user interfaces to activate scenes and

sequences.

Dimensions

Specication

Electrical

Supply: 230 volts -/+ 10% 50/60 Hz 1 Amp

(optionally, 127 volt 60 Hz)

Protection: Requires external circuit breaker

Load Types:

DMX controlled loads

Terminal Sizes:

Incoming supply, max’ cable size: 4mm2

iCANnetTM network cable size: 5 x 1mm2

DMX output: 2 x 1mm2

Memory:

FLASH memory to be able to upgrade software

EEPROM for 128 scene memory

Fade Times: 0.1 seconds to 60 minutes

Environmental Data

Temperature: 00C to 400C

Humidity: 0 to 95% non-condensing

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 4

Mounting

The unit is provided with four 6mm diameter ﬁxing holes for wall mounting.

The mounting holes can be accessed by undoing the four screws on the front cover and

removing it.

The unit should be installed in a dry ventilated location, where ambient temperature and

humidity are within the operating temperature of the unit.

The unit has ventilation slots on its sides to allow convection cooling and under no

circumstances should these be blocked.

Recommended minimum clearance around the unit is 100mm each side of the unit and 50mm

above and below the unit if trunking with a depth greater than 50mm is used.

Connecting Mains Supply

This unit requires a nominal 230V single phase supply (Live, Neutral and Earth) with 1A capability.

A separate isolator and secure mains earth are required.

All wiring should be completed in accordance with local wring regulations.

The unit is supplied with a knockout for mains cable entry. An appropriate cable gland should be

ﬁtted to the knockout hole provided to protect the mains cable from damage.

Ensure all mains connections are fully tightened and lock-washers used where supplied.

DMX Connections

The SCD24 has 24 channels

of DMX that can be

conﬁgured via

the iLight

programming software

Connections are made via the

4-way 2 part terminal block.

Connections are:

Function

Alarm

(N/A)

DMX+

DMX-

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 5

Network Termination

Network Connections

IMPORTANT NOTE: Connecting a mains potential cable to the iLight Network terminals is likley

to damage the unit and others connected, and invalidate warranty.

Termination On = Jumper across upper pins

Termination Off = Jumper across lower pins

IMPORTANT: Ensure jumper is in the off

position for all devices other than those at the

the end-of-line.

Applies 120Ω resistor to the iCAN network.

Required at each end of the network cable run

only.

Function Network Cable Colour

0V Black

CAN L White

Shield Silver

CAN H Blue

+12Vdc Red

Connections for the iCAN network are located on the CPU card at the bottom of the unit with

the cover removed.

There are two 5-way green connectors for the network. Either of

these may be used (as an in and an out) or a single used with the

network cable doubled-up to it.

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 6

Service Switches and LEDs

These switches and LEDs are located at the base of the unit.

The two service switches on the source controllers are used for the following:

• Entering Diagnostic Mode.

• Putting the Source Controller in

override mode.

• Sending a message to identify

the device on the network.

• Sending a message to identify

the device on the network.

The LEDs indicate the following:

• Normal operation:

Steady green LED blinking

1 x per second.

Red LED off.

• Message transmission and

receipt indicated by red LED

flashing for duration of data

transmission.

• Override status: Both LEDs

flashing together or just red

flashing and green off.

ICAN network error status will occur

when a Source Controller is not

connected to an iCAN network for

any reason. Once either connected

to a network of one or more other

devices which are powered the error

status will be removed. It is still

possible to enter Diagnostic mode

if a Source Controller is in iCAN

network error status.

Eaton Lighting Systems iLight Product Series - SCD24 IM7524 iss 4 7

Override Mode

Placing the unit into override mode

allows for testing of the Source

Controller outputs regardless of how

the unit is currently programmed. This is

useful for testing power to circuits prior

to the system being commissioned or

for fault ﬁnding where it can be used to

test if there is an issue with the Source

Controller output(s) should this be

suspected.

When the Source Controller is placed

into override mode it will no longer

respond to commands sent over the

iCAN network.

Override mode can also be used to

restore power to outputs if control is

lost or termporarly removed to allow

lighting to remain on until control is

restored.

NOTE: Override mode only affects the

outputs on the Source Controller on

which it is activated.

To exit diagnostic / override status

follow the steps shown. If power is

cycled to the Source Controller then this

will also take the unit out of override

mode and it will start up in the default

running status.

Document SCD24 IM7524 Issue 4

iLight Technical Support

Tel: +44 (0)844 324 9100 (available Mon-Fri 9am-5pm GMT)

Email: Tec[email protected]

Web: www.iLight.info

WARNING HAZARDOUS VOLTAGES

DISCONNECT FROM SUPPLY

BEFORE REMOVING COVERS

NO USER SERVICEABLE PARTS INSIDE

SERVICE BY QUALIFIED PERSONNEL ONLY

WARNING

To reduce the risk of ﬁre or electric shock,

DO NOT expose this device to rain or moisture.

DO NOT energise unless the front cover is in place.

This device must be earthed.

Installation, programming and maintenance must be carried out by qualiﬁed personnel.

Eaton Lighting Systems cannot accept responsibility for repairs or modiﬁcations that are not

competently executed and in accordance with service or upgrade information.

CE compliant to all relevant standards

Eaton Lighting Systems

Usk House, Lakeside, Llantarnam Park,

Cwmbran, NP44 3HD, UK

T: +44 (0)1923 495495 F: +44 (0)1923 228796

E: [email protected] EatonLightingSystems.com

All products manufactured by Eaton Lighting Systems and identiﬁed with the iLight product series

mark are warranted to be free from defects in material and workmanship and shall conform to

and perform in accordance with Seller’s written speciﬁcations. For detailed warranty information,

contact Eaton Lighting Systems.

This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods

found to be defective, upon their authorized return to Seller. This limited warranty does not apply

if the goods have been damaged by accident, abuse, misuse, modiﬁcation or misapplication, by

damage during shipment or by improper service.

There are no warranties, which extend beyond the hereinabove-limited warranty,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE

IMPLIED WARRANTY OF FITNESS.

No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the

Seller or to assume for the Seller any other liability in connection with any of its goods except in

writing and signed by the Seller. The Seller makes no representation that the goods comply with

any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s

responsibility.

The use of the Seller’s goods should be in accordance with the provision of the National Electrical

Code, UL and/or other industry or military standards that are pertinent to the particular end use.

Installation or use not in accordance with these codes and standards could be hazardous.

Inhaltsverzeichnis

Andere Eaton Controller Handbücher

Eaton

Eaton CGLine+ Web-Controller Bedienungsanleitung

Eaton

Eaton Vickers SMC20 Bedienungsanleitung

Eaton

Eaton PKE-SWD-32 Bedienungsanleitung

Eaton

Eaton COOPER POWER SERIES Handbuch

Eaton

Eaton EC500 Bedienungsanleitung

Eaton

Eaton OPTE9 Bedienungsanleitung

Eaton

Eaton WaveLinx series Bedienungsanleitung

Eaton

Eaton EMS-SWD Series Bedienungsanleitung

Eaton

Eaton AMPGARD Handbuch

Eaton

Eaton EFX48 e-Fuse Series Betriebsanleitung

Eaton

Eaton EM4-201-DX2 Bedienungsanleitung

Eaton

Eaton DCF 800 TWIN Bedienungsanleitung

Eaton

Eaton DS7 Series Bedienungsanleitung

Eaton

Eaton A200 Bedienungsanleitung

Eaton

Eaton Greengate RC3 Bedienungsanleitung

Eaton

Eaton EMS2 SWD Series Bedienungsanleitung

Eaton

Eaton Smart Home Controller 2.0 Bedienungs- und Wartungsanleitung

Eaton

Eaton Cutler-Hammer W200 Bedienungsanleitung

Eaton

Eaton ATC-900 Bedienungsanleitung

Eaton

Eaton CAAE-01/01 Handbuch

Eaton

Eaton Crouse-hinds series Bedienungsanleitung

Eaton

Eaton ESWA4500C Bedienungsanleitung

Eaton

Eaton Cuttler-Hammer Pow-R-Command 100 Gebrauchsanweisung

Eaton

Eaton A201 Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch