Eaton DFDAP-M Bedienungsanleitung
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
Effective: March 2011
iEATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
Effective: March 2011
1. 1
2. 1
2.1 2
2.2 2
2.2.1 Pump Running check 2
2.2.2 Common Alarm check 2
2.2.3 Phase Failure check 2
2.3 2
2.3.1 Engine Running' & 'Controller in OFF Mode' check 2
2.3.2 Common Alarm' and 'Low Fuel' check 2
2.4 3
2.4.1 Lamp Test Button 3
2.4.2 Normal and Supervisory (Backup) Voltage 3
2.4.3 Audible Alarm 3
2.4.4 Silence Alarm Button 3
2.4.5 Normal Power ON LED 3
2.4.6 Output Contacts 3
2.4.7 Output Relays 3
2.4.8 Alarm Inputs 3
3. 4
4. 5
5. 6
6. 7
ELECTRICAL CONNECTIONS
TABLE OF CONTENTS
INSTALLATION AND MOUNTING OF THE CONTROLLER
FIGURE 1: ELECTRIC DIMENSIONS & SHIPPING WEIGHTS
FIGURE 2: DIESEL DIMENSIONS & SHIPPING WEIGHTS
FIGURE 3: ELECTRIC WIRING SCHEMATIC
FIGURE 4: DIESEL WIRING SCHEMATIC
ELECTRICAL CHECKOUT INSTRUCTIONS
ELECTRIC ALARM PANELS
DIESEL ALARM PANELS
OPERATION
INSTALLATION & MAINTENANCE
MANUAL FOR REMOTE ALARM
PANELS
In order to familiarize yourself with the Remote
Alarm Panel, please read the instruction manual
thoroughly and carefully. Retain the manual for
future reference.
1. Installation and Mounting of the
Controller
Carefully unpack the controller and inspect
thoroughly.
The controller is not free standing and must be
bolted securely to a wall. For dimensional and
weight data please refer to the respective data
sheets for the Remote Alarm Panels.
Figure #1 - Electric Remote Alarm Panel
Figure #2 - Diesel Remote Alarm Panel
2. Electrical Connections
All electrical connections should meet national
and local electrical codes and standards.
The controller should be located or so protected
that they will not be damaged by water escaping
from pumps or pump connections. Current carrying
parts of controllers shall be a minimum of 12 inches
(305 mm) above the floor level.
? Prior to starting, verify all data on the
nameplate such as, catalog number and AC line
voltage.
? Inspect all electrical connections,
components and wiring for any visible damage and
correct as necessary. Ensure that all electrical
connections are tightened before energizing.
? Install necessary conduit using proper
methods and tools.
? Incoming Normal power and Supervisory
(backup) power connections are clearly marked L
and N and are located on the upper right side of the
microprocessor board.
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
1
EATON Corporation www.chfire.com
Effective: March 2011
2.1 Electrical Checkout Instructions (For Use with Eaton Remote Alarm Panels)
WARNING:The following procedures should be carried out by a qualified electrician familiar with the electrical safety
procedures associated with this product and its associated equipment.
2.2 Electric Remote Alarm Panels (Full Service) – For Electrical Schematic Refer to Figure #3
Note: The alarm buzzer can be silenced by pressing the 'Silence Alarm' button on the front of the controller.
2.2. - Turn power on to the Fire Pump Controller and to the Remote Alarm Panel
- In the Fire Pump Controller press the 'Local Start' pushbutton, the controller will start
- The 'Pump Running' LED should illuminate and the alarm will sound on the Alarm Panel
- Press the 'Stop' pushbutton on the front of the fire pump controller
2.2. - Move the disconnect handle on the Fire Pump Controller to the 'OFF' Position
- The 'Common Alarm' and 'Phase Failure' LED's should illuminate and the alarm will sound on the Alarm Panel
- Move the disconnect handle back to the 'ON' Position
2.2.3 - In the menu under the Alarm category, change the phase rotation to the opposite of what it is currently set for.
- The 'Common Alarm' and 'Phase Reversal' LED's should illuminate and the alarm will sound on the Alarm
Panel
- Return the menu setting to the correct rotation.
2.3 Diesel Remote Alarm Panels – For Electrical Schematic Refer to Figure #4
Note: The alarm buzzer can be silenced by pressing the 'Silence Alarm' button on the front of the controller.
2.3.1 - Turn power on to the Fire Pump Controller and to the Remote Alarm Panel
- Place the controller in the 'AUTO' mode by turning the Main Switch to “AUTO”
- Start the controller by pushing the “Engine Test" button on the Diesel controller membrane / keypad,
then push the “Acknowledge” button.
- The 'Engine Running' light should illuminate and the alarm will sound on the alarm panel
- Place the controller in the 'OFF' mode by turning the Main Switch to “OFF”
- The 'Not in Auto Mode' LED will illuminate and the alarm will sound on the alarm panel
2.3.2 - Place the controller in the 'AUTO' mode by turning the Main Switch to “AUTO”
-
- Place a jumper between Terminal #38 & #11 in the Fire Pump Controller (Low Fuel)
- The 'Common Alarm’ and ‘Low Fuel’ LED’s should illuminate and the alarm will sound on the alarm panel
- Place the controller in the 'OFF' mode by turning the Main Switch to “OFF”
Start the controller by pushing the “Engine Test" button on the Diesel controller membrane / keypad,
then push the “Acknowledge” button.
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
2EATON Corporation www.chfire.com
Effective: March 2011
2.4 Operation
2.4.1 Lamp Test Button
Each remote alarm panel is equipped with a Lamp Test
button that fully tests all LED’s when pressed. Operating
the lamp test button will not change the state of the
internal output relays
2.4.2 Normal and Supervisory (backup)
Supply Voltage
The remote alarm panels will accept both 120 volt
50/60Hz and 240 volt 50/60Hz power supply on either of
the normal and supervisory (backup) source inputs. If the
normal source of supply is lost, the panel will
automatically switch to the supervisory (backup) source.
Both the normal and supervisory (backup) sources must
be independent of each other.
2.4.3 Audible Alarm
When any alarm conditions are present, the audible
alarm will sound. It will continue to sound until either the
silence alarm button is pressed, or the alarm condition is
satisfied.
2.4.4 Silence Alarm Button
An audible alarm silencing button is provided that
silences all active alarms when pressed. Pressing the
button has no effect on the associated alarm LED(s).
Should a second alarm condition occur after the silence
button has been pressed, the audible alarm will re-sound
until the silence button is pressed again, or the alarm
condition has been satisfied.
2.4.5 Normal Power ON LED
The normal power ON LED indicates when normal power
is available and will turn off when the controller switches
to the supervisory (backup) power source. An audible
alarm will sound when normal power is not available and
will remain ON until normal power is restored, or the
silence pushbutton is pressed.
2.4.6 LED Visual Indicators
The FDAP-M electric remote alarm panel has four LED
visual indicators to indicate Pump Running, Phase
Failure, Common Alarm and Phase Reversal. The
DFDAP-M diesel remote alarm panel also has four LED
visual indicators that indicate Not in AUTO Mode, Engine
Running, Common Alarm and Low Fuel.
3
EATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
2.4.7 Output Relays
The relays are printed circuit board style mounted on the
alarm panel main circuit board. They are rated for
8 amps / 250VAC. They are de-energized under normal
conditions regardless of input status selected.
2.4.8 Alarm Inputs
Each controller is equipped with eight user selectable
alarm inputs. Each can be selected as normally open
(N.O.) or normally closed (N.C.) by the use of jumpers on
the microprocessor board.
Two Form-C alarm output relays can be programmed to
indicate specific alarm conditions.
Effective: March 2011
Electrical Remote Alarm Panel - FDAP-M
FIGURE 1
4EATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
N. Y. C.
APPROVED
15.49 [393] 11.56 [294]
9.55 [243]
4.74 [120]
8.00 [203]
9.75 [248]
n0.27 [n7]x4
WALL MTG. HOLES
NOTE:
1. ALL ENCLOSURES FINISHED IN FIRE PUMP RED
2. CABLE ENTRANCE EITHER TOP OR BOTTOM
3. STANDARD ENCLOSURE TYPE NEMA 1
Effective: March 2011
Diesel Engine Remote Alarm Panel - DFDAP-M
FIGURE 2
5
EATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
N. Y. C.
APPROVED
15.49 [393] 11.56 [294]
9.55 [243]
4.74 [120]
8.00 [203]
9.75 [248]
n0.27 [n7]x4
WALL MTG. HOLES
NOTE:
1. ALL ENCLOSURES FINISHED IN FIRE PUMP RED
2. CABLE ENTRANCE EITHER TOP OR BOTTOM
3. STANDARD ENCLOSURE TYPE NEMA 1
Effective: March 2011
Wiring Schematic - Electric Remote Alarm Panel - FDAP-M
FIGURE 3
6EATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
N. Y. C.
APPROVED
:
Effective: March 2011
Wiring Schematic - Diesel Remote Alarm Panel - FDAP-M
FIGURE 4
7
EATON Corporation www.chfire.com
O & M Manual IM05805008K
Remote Alarm Panels
EATON DFDAP-M / FDAP-M
Effective: March 2011
N. Y. C.
APPROVED
:
Eaton Corporation
10725 - 25th Street NE Unit 124
, Alberta, Canada
T
Tel: +1-403-717-2000
Fax: +1-403-717-0567
email: [email protected]
www.chfire.com
Calgary
3N 0A4
©2011 Eaton Corporation
All Rights Reserved
Printed in Canada
Publication No.: IM05805008K
March 2011
Dieses Handbuch passt für folgende Modelle
1
Andere Eaton Sicherheitssystem Handbücher
Eaton
Eaton 403-AP Handbuch
Eaton
Eaton i-on30R+ Bedienungsanleitung
Eaton
Eaton SDR-REXT Bedienungsanleitung
Eaton
Eaton 415-TF Handbuch
Eaton
Eaton BG Bedienungsanleitung
Eaton
Eaton PH1 Bedienungsanleitung
Eaton
Eaton i-on Style Bedienungsanleitung
Eaton
Eaton BiWire Ultra EF009SB Bedienungsanleitung
Eaton
Eaton Crouse-hinds series Bedienungsanleitung
Eaton
Eaton i-on1000EX Bedienungsanleitung
Eaton
Eaton 405-M Handbuch
Eaton
Eaton Funke+Huster Fernsig TWIN-EExll Bedienungsanleitung
Eaton
Eaton i-on30EXL Bedienungsanleitung
Eaton
Eaton i-on16 Bedienungsanleitung
Eaton
Eaton CU1 Series Bedienungsanleitung
Eaton
Eaton i-on40 Bedienungsanleitung
Eaton
Eaton RTK 725B range Bedienungsanleitung
Eaton
Eaton BDK22 Bedienungsanleitung
Eaton
Eaton FHF DSLB 20 LED Bedienungsanleitung
Eaton
Eaton SM87BG Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung